Cleaning; Removing The Blade; Fitting The Blade; How To Charge The Battery - Husqvarna ROYAL 43 Operator's Manual

IMPORTANT
Release the Operator Presence Control, to stop the engine, wait until the blade has stopped and
disconnect the spark plug lead:-
- before clearing a blockage;
- before checking, cleaning or working on the appliance
IMPORTANT
Never use water for cleaning your lawnmower. Do
not clean with chemical, including petrol, or solvents
- some can destroy critical plastic parts.

Cleaning

• Disconnect the spark plug lead.
• Turn machine on it's side with the exhaust uppermost.
1. Remove grass from under the deck with a
brush.(L1 and L2)
2. Using a soft brush - remove grass clippings from
the engine air intakes and exhaust (L3), cutting
height adjustment area, around the wheels (L4)
and the grass collector.
3. Wipe over the surface of your lawnmower with a
dry cloth.
L1
L3
Cutting System

Removing the Blade

• Disconnect the spark plug
lead.
• Turn machine on it's side
with the exhaust uppermost.
1. Use spanner to loosen
blade bolt by turning anti-
clockwise.(M)
2. Remove the blade bolt, blade and spacer washer.
3. Inspect for damage and clean as necessary.

Fitting the Blade

1. Fit the blade to the machine with the sharp
edges pointing away from the machine.
2. Re-assemble blade bolt through blade and
spacer washer.
3. Hold firmly and tighten blade bolt firmly with a
spanner. Do not over tighten.
IMPORTANT
Do not attempt any maintenance on your
lawnmower when the engine is hot.
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Renew your metal
blade after 50 hours mowing or 2 years whichever is
the sooner - regardless of condition. If the blade is
cracked or damaged replace it with a new one.
ENGLISH - 7
MAINTENANCE
L2
L4
M
How to Charge the Battery (ROYAL 43SE)
1. Stop your lawnmower.
2. Disconnect the spark plug.
3. Remove the cap from
the charging point at the
bottom of the wiring
loom.(N)
4. Plug charger lead into
connection on battery
loom.(N)
5. Plug the battery charger
into a domestic electric socket.
6. Charging will then commence.
7. Charge for 24 hours.
8. After charging, disconnect the charger from the
socket and charging point.(N)
9. Replace the cap on the charging point.(N)
10. The unit is now ready for use.
ENVIRONMENTAL INFORMATION
Electrolux Outdoor Products are manufactured under
an Environmental Management System (ISO 14001)
using, where practical, components manufactured in
the most environmentally responsible manner,
according to company procedures, and with the
potential for recycling at the end of the products' life.
• Packaging is recyclable and plastic components
have been labelled (where practical) for
categorised recycling.
• Awareness of the environment must be
considered when disposing of 'end-of-life' product.
• If necessary, contact your local authority for
disposal information.
BATTERY DISPOSAL
• The battery should be taken to an Approved
Service Centre or your local Recycling Station.
• Do NOT dispose of used battery with
household waste
• Lead/Acid batteries can be harmful and
should be disposed of through the
recognised recycling facility in accordance
with European Regulation
• Do NOT dispose of battery to water.
• Do NOT incinerate
DISPOSAL OF FUELS AND LUBRICATING OILS
• Wear protective clothing when handling any
fuels and lubricants.
• Avoid contact with skin.
• Remove petrol and engine oil before transporting
the product.
• Contact your local authority for information of
your nearest Recycling/Disposal Station.
• Do NOT dispose of used fuels/oils with
household waste
• Waste fuels/oils are harmful, but can be
recycled and should be disposed of through
the recognised facilities.
• Do NOT dispose of used fuels/oils to water.
• Do NOT incinerate
N
Wiring Loom
charging
point cap