Sanyo PLC-XE32 Service Manual page 38

Electrical Adjustments
Group/
Item Name
Item
3 GAIN AREA V START
4 Image AREA H WIDTH
5 Image AREA V HIGHT
6 OFFSET target
7 OFFSET torelance
8 GAIN target
9 GAIN torelance
Group 6 Auto Calibration (CVBS/SVIDEO)
0 Y Image Area Start X
1 Y Image Area Start Y
6 Image Area H Width
7 Image Area V Hight
8 Y Target Level
11 Gain Tolerance
1 Delta Gain
Group 64 Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START
1 Y-OFFSET AREA V START
 CB - OFFSET AREA H START
3 CB - OFFSET AREA V START
4 CR - OFFSET AREA H START
5 CR - OFFSET AREA V START
6 Y - GAIN AREA H START
7 Y - GAIN AREA V START
8 CB - GAIN AREA H START
9 CB - GAIN AREA V START
10 CR - GAIN AREA H START
11 CR - GAIN AREA V START
1 Image AREA H WIDTH
13 Image AREA V HIGHT
14 Y - OFFSET TARTGET
15 CB OFFSET TARGET
16 CR OFFSET TARGET
17 Y - GAIN TARGET
18 CB - GAIN TARGET
19 CR - GAIN TARGET
0 OFFSET torelance
1 GAIN torelance
Group 80 AutoPC Adjsut
0 AutoPCAdjustEnable
1 Frequency Step
 Frequency Threshold
3 Fine Phase
4 BLKDET
5 PHASEMSK
Group 90 PanelType * Panel Type Check
0 GammaL/R-View
1 GammaL/R-Change
Group 500 Composite (NTSC) Composite / S-Video
0
1 Disp Dots
 H Back Porch
3 V Back Porch
4 Disp Line
Group 501 Composite (PAL) Composite / S-Video
0
1 Disp Dots
 H Back Porch
3 V Back Porch
4 Disp Line
Group 50 Composite (SECAM) Composite / S-Video
0
1 Disp Dots
 H Back Porch
3 V Back Porch
4 Disp Line
Group 510 SCART(480i)
0
Function
White Level Acquiring Area V-Start
Position
Black/White Level Acquiring Area
Black/White Level Acquiring Area Height
Target Value of Black Level Adj.
Torelance of Black Level Adj.
Target Value of White Level Adj.
Torelance of White Level Adj.
Y Acquiring Area H-Start Position
Y Acquiring Area V-Start Position
Image Level Acquiring Area
Image Level Acquiring Area Height
Target Value of Y Level Adj.
Torelance of Level Adj.
Deviation Width of Gain Value
Y - Offset Acquiring Area H-Start Position
Y - Offset Acquiring Area V-Start Position
CB - Offset Acquiring Area H-Start Position
CB - Offset Acquiring Area V-Start Position
CR - Offset Acquiring Area H-Start Position
CR - Offset Acquiring Area V-Start Position
Y
YCBCR Level Acquiring Area
YCBCR Level Acquiring Area Height
Torelance of OFFSET Adj.
Torelance of GAIN Adj.
Auto-PC Adj Operation Enable if Un-
supported Signal Input
Frequency Steps of TotalDot
Total Dot Freqency Threshold
Do Phase Adj after Total Dot Adj.
Black Level Detection Area
Phase Detection Filter
Current Setting Check
Setting of Gamma
Initial
500
13
9
3
1
38
1
0
500
13
0
17
1
9
900
500
900
500
900
500
50
500
800
500
700
500
8
13
4
18
18
17
37
37
1
1
0
1
5
1
1
0
0
10
668
3

450
664
3

534
65
8
10
550
-38-
Range Note
0 - 1000
0 - 4095
0 - 4095
0 - 17
1 - 17
0 - 55
1 - 55
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 55
0 - 55
0 - 55
0 - 1000
0 - 1000
0 - 1000 If not used: use Y's value
0 - 1000 If not used: use Y's value
0 - 1000 If not used: use Y's value
0 - 1000 If not used: use Y's value
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 1000
0 - 4095
0 - 4095
0 - 55
0 - 55
0 - 55
0 - 55
0 - 55
0 - 55
1 - 55
1 - 55
0 - 1 0: Enable, 1: Disable
0-3
0 - 10 0 [] <--- -----> 10[Not matched]
0 - 1 0: Executes Fine Phase, 1: Not Execute
0 - 3
0: Effective All Bit,
1: Disable Lower 1 bit
0 - 3
: Disable Lower  bit, 3: Disable Lower 3
bit
0: Gamma for L-Turn
0-0
0: Gamma for R-Turn * Read only
Sets L-Turn Gamma if the Value is set to 0.
0-0 Sets R-Turn Gamma if the Value is set to
0.
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095
0 ~ 4095