Sanyo PLC-XE32 Service Manual page 30

Electrical Adjustments
Group/
Item Name
Item
150 PreCoast YCbCr 480i
151 PostCoast YCbCr 480i
15 PreCoast YCbCr 575i
153 PostCoast YCbCr 575i
154 PreCoast YCbCr 480p
155 PostCoast YCbCr 480p
156 PreCoast YCbCr 575p
157 PostCoast YCbCr 575p
158 PreCoast YCbCr 70p 60Hz
159 PostCoast YCbCr 70p 60Hz
160 PreCoast YCbCr 70p 50Hz
161 PostCoast YCbCr 70p 50Hz
16 PreCoast YCbCr 1080i 60Hz
163 PostCoast YCbCr 1080i 60Hz
164 PreCoast YCbCr 1080i 50Hz
165 PostCoast YCbCr 1080i 50Hz
166 PreCoast YCbCr 1035i
167 PostCoast YCbCr 1035i
180 PreCoast SCART 480i
181 PostCoast SCART 480i
18 PreCoast SCART 575i
183 PostCoast SCART 575i
Group 10 Sync Processor
0 SYNCAMPHLCKTOLOW
1 SYNCAMPHLCKTOHI
Group 0 Video Decoder
0 Y Level
1 C Level

3 XCXL Level
4 CDNBANDWIDTH
5 CDWBANDWIDTH
6 CDCNMINLEAK
7 CDCNSLOPELEAK
8 CDCWMINLEAK
9 CDCWSLOPELEAK
10 COMBLEAKBPGAIN
11 CDBDIAGONALGAIN
1 CDNBCWBCLGAIN
13 RLUMASETUP-Enable
Group 40 General
0 IP Mode
1 3: PullDown Mode
 Detect Film Mode Enable
3 Force IP Mode
Group 41 Deinterlacer setting Effective only for Progressive ON-L1 mode.
0 Motion Adaptive Weight Value <KDEINT>
1 Angle Interpolation Level
 CUE Low Pass Filter Enable
Group 4 Deinterlacer setting Effective only for Progressive ON-L mode.
0 Motion Adaptive Weight Value <KDEINT>
1 Angle Interpolation Level
 CUE Low Pass Filter Enable
Group 43 Deinterlacer setting Effective only for Progressive ON/Film mode.
0 Motion Adaptive Weight Value <KDEINT>
1 Angle Interpolation Level
 CUE Low Pass Filter Enable
Group 45 Noise Reduction (Time) Effective only for N.R - Off
Function
Minimum sync amplitude threshold for
HLCK 1 to 0 tansition
Minimum sync amplitude threshold for
HLCK 0 to 1 tansition
Composite / S-Video - Y Level (ADC RGB
Gain)
Composite / S-Video - C Level (ADC
Saturation)
Cross-Chroma, Cross-Luma Level
Comb D Narrow Bandwidth
Comb D Wide Bandwidth
Comb D Chroma Narrow Band
Minimum Leakage
Comb D Narrow Band Slope Leakage
Comb D Wide Band Minimum Leakage
Comb D CW Slope Leakage
Comb Leak To Ban Pass Gain
Comb D Band Pass Diagonal Gain
Comb D Narrow Band Comb Wide
Band Comb
7.5IRE Setup Enable
Sets for IP Off
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
0 : Conservative <====> 4 : Aggressive
<CUELPFEN>
Initial
7
13
7
13
7
13
7
13
7
13
7
13
7
13
7
13
7
13
7
13
7
13
0x1000
0x700
10 / 10
115 / 115
3
3 / 3
4 / 4
0 / 3
7 / 7
1 / 3
6 / 6
1 / 0
1 / 3
1 / 1
0
1
1
0

30
4
0
0

0
30
4
0
-30-
Range Note
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 63
0 - 9999
0 - 9999
*R : Read Only Value
0 - 55
0 - 55 Composite / S-Video
0 - 5
0 - 3
0 - 7 NTSC/PAL
Left Values are adjustable if CXCL Level
0 - 3
= 5.
0 - 7
0 - 3
0 - 7
0 - 3
0 - 3
0 - 3
0 - 1 Effective only NTSC Signal
0: IP Block not used
0 - 1
1: IP OFF used with IP Block
bit0 : Global Motion
1 - 3
bit1 : Video Motion
0 : :3pull down & :pull down
0 -  1 : :3pull down
 : :pull down
0 : IP Process Disable
1 : Force Normal IP Mode
0 - 
 : Force Film Mode
Effective only for PSF Signal.
0 - 55
0 - 4
0 - 1
0 - 55
0 - 4
0 - 1
0 - 55
0 - 4
0 - 1