Page 1
T O Y O T A N A V I G A T I O N S Y S T E M RAV4 (RHD) INSTALLATION INSTRUCTIONS ** A2 * R PART NUMBER 08545-00802 NAVIGATION KIT TOYOTA MOTOR CORPORATION N2RA2/W-7.pdf...
RAV4 (A2) TNS 200 PRECAUTIONS PLEASE READ THOROUGHLY THESE PRECAUTIONS BEFORE THE INSTALLATION • Be sure to disconnect the negative • Protect your car with fender cov- (-) lead from the battery terminals. ers, seat and so on. • Do not pinch the rear wiring or har- •...
RAV4 (A2) TNS 200 REQUIRED PARTS CD-ROM To be ordered separately. Please refer to the list of available CD-ROM for TNS200 Navigation System (Access to accessories). OWNER’S MANUAL To be ordered separately. 05-01 RAV4 (RHD) - 10...
RAV4 (A2) TNS 200 INSTALLATION OF THE GPS ANTENNA Cut the foam into 2 large pieces and 14 small pieces as shown in the illustration. x 14 Fig. 10 Cut the butyl tape into pieces of 10mm width. Remove the release paper of the earth...
Page 17
RAV4 (A2) TNS 200 Route the antenna cord as shown in the illustration. According to the illustration , push down the lower steering column cover , and return the meter cluster its original position, without rubbing the GPS antenna against the instru-...
RAV4 (A2) TNS 200 WIRE HARNESS INSTALLATION Route the wire harness and GPS antenna along the midconsole area to the ECU location. Fig. 13 The connectors shown in the illustra- tion are the vehicle side connectors to be spliced. Fig. 14...
Page 19
RAV4 (A2) TNS 200 TX WIRE CONNECTION Connect the TX(-) wire of the wire har- ness to the vehicle side 12P con- nector terminal 9. Connect the TX(+) wire of the wire harness to the vehicle side 12P connector terminal 10.
Page 20
RAV4 (A2) TNS 200 Connect the reverse sensor wire the wire harness to the 28P WIRE SIDE VIEW connector terminal 27. Reconnect the 28P connector to the driver’s side J/B. Fig. 19 Connect the wire harness 10P con- nector to the vehicle side 10P connec- tor.
Page 21
RAV4 (A2) TNS 200 11. Attach the wire harness and anten- Vehicle wire harness na cord to the reinforcement using the wire ties (3x). Reinforcement Excess main wire harness Fig. 22 12. Route the main wire harness antenna cord along the midconsole and then under the carpet behind the cross member.
Yaris RAV4 (A2) TNS 200 TNS 200 INSTALLATION OF THE COMPUTER Cut the butyl tape into 2 large pie- ces and 2 small pieces as shown. Attach the butyl tape to the bottom of the brackets CAUTION: Do not remove the relea-...
Page 23
RAV4 (A2) TNS 200 Route the main wire harness through the carpet. Attach the butyl tape to the vehicle floor as shown. Cut out the insulation mat according the dimensions indicated and put it on top of the butyl tape Cut out Fig.
Page 24
RAV4 (A2) TNS 200 Connect the 1P connector (GPS anten- ), 8P connector and 13P connector (wire harness ) to the computer Push in the slitted carpet under the computer Fig. 28 05-01 RAV4 (RHD) - 24...
RAV4 (A2) TNS 200 INSTALLATION OF NAVIGATION DISC Connect the battery and turn the igni- tion switch to the ACC position. Slide the eject switch on the computer to the left to open the disc insertion slot. With the label side of the disc facing up, insert the Navigation Disc into the disc insertion slot.
2. Press the NAVI switch and confirm that the navigation screen is displayed. 3. Adjust the volume by following the section on ”Adjusting the Volume of the Guide Voice” in the TNS 200 Owner’s Manual, and confirm that the sound from the speakers changes.
RAV4 (A2) TNS 200 REASSEMBLING Return all vehicle parts that have been removed to their original locations. Especially make sure to attach trim and other interior materials properly so that they do not have a detrimental effect on the function of the vehicle. During restoration, make sure that wires are not pinched and all bolts and screws are tightened.