Advanced Features
Listening through a Receiver
¦
You can listen to sound through a receiver (i.e Home Theater) instead of the TV speaker.
1. Select Receiver and set to On.
2. Press the
EXIT
button to exit.
✎
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the
OUT (OPTICAL)
✎
When the receiver (i.e Home Theater) is set to
the TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
✎
NOTE
x
You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.
x
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet
x
The Anynet
functions do not operate with other manufacturers' products.
+
Troubleshooting for Anynet
¦
Problem
Anynet
does not work.
+
I want to start Anynet
.
+
I want to exit Anynet
.
+
The message 'Connecting to
Anynet
device...' appears on
+
the screen.
The Anynet
device does not
+
play.
The connected device is not
displayed.
The TV Program cannot be
recorded.
The TV sound is not output
through the receiver.
34
English
BN68-02741A_Eng.indb 34
jack of the TV.
On, you can hear sound output from the TV's Optical jack. When
+
Possible Solution
•
Check if the device is an Anynet
•
Only one receiver (home theater) can be connected.
•
Check if the Anynet
+
device power cord is properly connected.
•
Check the Anynet
device's Video/Audio/HDMI cable connections.
+
•
Check whether
Anynet
(HDMI-CEC) is set to On in the Anynet
+
•
Check whether the TV remote control is in TV mode.
•
Check whether the remote control is Anynet
•
Anynet
doesn't work in certain situations. (Searching channels, operating Media Play or Plug & Play
+
(initial setup), etc.)
•
When connecting or removing the HDMI cable, please make sure to search devices again or turn your
TV off and on again.
•
Check if the Anynet
Function of Anynet
+
•
Check if the Anynet
device is properly connected to the TV and check if the Anynet
+
set to On in the Anynet
Setup menu.
+
•
Press the
TOOLS
button to display the Anynet
•
Select
View TV in the Anynet
•
Press the
SOURCE
button on the TV remote control and select a device other than Anynet
•
Press
> CH
CH
LIST, PRE-CH, and
<,
button operates only when a tuner-embedded Anynet
•
You cannot use the remote control when you are configuring Anynet
•
Use the remote control when the Anynet
•
You cannot use the play function when
•
Check whether or not the device supports Anynet+ functions.
•
Check whether or not the HDMI cable is properly connected.
•
Check whether
Anynet
(HDMI-CEC) is set to On in the Anynet
+
•
Search Anynet
devices again.
+
•
You can connect an Anynet
Anynet
functions.
+
•
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a
power failure, please repeat the device scan.
•
Check whether the antenna jack on the recording device is properly connected.
•
Connect the optical cable between TV and the receiver.
device. The Anynet
system supports Anynet
+
+
+
compatible.
+
device is set on.
+
menu and select a menu you want.
+
menu.
+
FAV.CH
to change the TV mode. (Note that the channel
device is not connected.)
+
setting or switching to view mode is complete.
+
Plug & Play (initial setup) is in progress.
+
device using the HDMI cable only. Some HDMI cables may not support
+
DIGITAL AUDIO
device.
+
devices only.
+
setup menu.
(HDMI-CEC) is
+
devices.
+
or switching to a view mode.
+
setup menu.
2/24/2010 7:09:02 PM