I
Listening through a Receiver
You can listen to sound through a receiver (i.e Home Theater) instead of the 1V speaker.
1.
Select Receiver and set to On.
2.
Press the EXIT button to exit.
~ If your receiver supports audio only, it may not appear in the device list.
~
The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO
OUT (OPTICAL) jack of the TV.
~
When the receiver (i.e Home Theater) is set to On, you can hear sound output from the TV's Optical jack. When
the TV is displaying a OTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a OVO and is connected to the TV via HOMI, only 2 channel sound will be heard from
the receiver.
~ If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a
power failure), the Speaker Select may be set to External Speaker when you turn the TV on again.
~
NOTE
• You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.
• The TV remote control may not work under certain conditions. If this occurs, reselect the Anynett device.
• The Anynett functions do not operate with other manufacturers' products.
I
Troubleshooting for Anynet+
Problem
Possible Solution
Anynet+ does not work.
•
Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
·
Only one receiver (Home Theater) can be connected.
•
Check if the Anynet+ device power cord is properly connected.
•
Check the Anynet+ device's Video/Audio/HOMI cable connections.
·
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
•
Check whether the TV remote control is in TV mode.
·
Check whether the remote control is Anynet+ compatible.
·
Anynet+ doesn't work in certain situations. (Searching channels, operating Media Play or Plug & Play
(initial setup), etc.)
·
When connecting or removing the HOMI cable, please make sure to search devices again or turn your
TV off and on again.
·
Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.
•
Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is
set to On in the Anynet+ Setup menu.
·
Press the TV button on the TV remote control to switch to TV. Then press the TOOLS button to display
the Anynet+ menu and select a menu you want.
I want to exit Anynet+.
·
Select View TV in the Anynet+ menu.
·
Press the SOURCE button on the TV remote control and select a device other than Anynet+ devices.
·
Press
V
CH
A,
CH LIST, PRE-CH, and FAV.CH to change the TV mode. (Note that the channel
button operates only when a tuner-embedded Anynet+ device is not connected.)
The message 'Connecting to
·
You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
Anynet+ device... ' appears on
·
Use the remote control when the Anynet+ setting or switching to view mode is complete.
the screen.
The Anynet+ device does not
·
You cannot use the play function when Plug & Play (initial setup) is in progress.
play.
The connected device is not
·
Check whether or not the device supports Anynet+ functions.
displayed.
•
Check whether or not the HOMI cable is properly connected.
·
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
·
Search Anynet+ devices again.
·
You can connect an Anynet+ device uSing the HOMI cable only. Some HOMI cables may not support
Anynet+ functions.
·
If it is terminated by an abnormal situation such as disconnecting the HOMI cable or power cord or a
power failure, please repeat the device scan.
The TV Program cannot be
•
Check whether the antenna jack on the recording device is properly connected.
recorded.
The TV sound is not output
·
Connect the optical cable between TV and the receiver.
through the receiver.
English
37