Bosch PCM 8 S Original Instructions Manual page 30

OBJ_BUCH-557-005.book Page 30 Tuesday, July 5, 2011 4:08 PM
30 | English
64 Screw for bevel angle indicator
65 Screw for mitre angle indicator
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Sliding Mitre Saw
Article number
Rated power input
No-load speed
Laser type
Laser class
Weight according to
EPTA-Procedure 01/2003
Protection class
Permissible workpiece dimensions (maximal/minimal) see page 33.
Starting cycles generate brief voltage drops. Interference with other
equipment/machines may occur in case of unfavourable mains system
conditions. Malfunctions are not to be expected for system impedances
below 0.24 ohm.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Noise/Vibration Information
Measured sound values determined according to EN 61029.
Typically the A-weighted noise levels of the product are:
Sound pressure level 98 dB(A); Sound power level
111 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029:
2 2
a =3.5 m/s , K=1.5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
1 609 929 U68 | (5.7.11)
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
PCM 8 S
lowing standards or standardization documents: EN 61029,
3 603 L02 0..
EN 60825-1 according to the provisions of the directives
W 1200
2004/108/EC, 2006/42/EC.
-1
min 5200
Technical file (2006/42/EC) at:
Robert Bosch GmbH, Dept. PT/ESC,
nm 650
D-70745 Leinfelden-Echterdingen
mW < 1
Dr. Egbert Schneider
2
Senior Vice President
kg 18.7
Engineering
/II
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 31.03.2010
Assembly
Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
mm 210
Delivery Scope
mm 1.4–2.0
mm 30
– Sliding mitre saw with premounted saw blade
– Dust bag 1
– Locking knob 13
– Extension bar 19 (2x)
– Fastening kit for extension bar 40
(2 U-profiles with screws)
– Saw-table extension 39
– Length stop 38
– Quick-action clamp 49
– Allen key/Phillips screwdriver 20
– Batteries (3x, size LR03, 1,5 V)
for machine versions with base unit:
– Base unit 42
(16 Profiles, 4 end caps)
– Fastening kit for base unit 43
(24 screws with nuts for assembly, 4 screws with nuts for
fastening of the machine, 4 washers)
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
Dr. Eckerhard Strötgen
Head of Product
Certification
Please also observe the representation of
the delivery scope at the beginning of the op-
erating instructions.
Before starting the operation of the machine
for the first time, check if all parts listed be-
low have been supplied:
Bosch Power Tools