COMPUTER SEWING MACHINE HZL-L series INSTRUCTION MANUAL Please read this instruction manual before using the machine as it contains important operational Attention and safety information. Keep this manual accessible so that you may refer to it at anytime while operating the machine.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the following: This sewing machine is designed and manufactured for household use only. Read all instructions before using this sewing machine. DANGER — To reduce the risk of electric shock: 1.
TABLE OF CONTENTS NAMES OF PARTS DECORATIVE STITCHING Names of Parts ............... 2 Patchwork ..............40 Standard Accessories ............ 3 Shelltuck ............... 40 Applique ............... 41 GETTING READY TO SEW Fringing ................. 42 Connecting the Power Supply ........4 Drawn Work ..............42 Before Using Your Sewing Machine .......
NAMES OF PARTS Names of Parts ⑦ ⑧ ⑨ ⑩ ⑥ Extension table (Accessory box) ① ⑪ Needle plate ② ⑫ Needle threader ③ Thread cutter ④ ⑬ Face cover ⑤ ⑤ Thread take-up lever ⑥ ⑭ Thread tension dial ⑦...
Standard Accessories ① Zigzag foot A (set on the machine) ② Overedge foot C ③ Zipper foot E ④ Satin stitch foot F ① ② ③ ④ ⑤ ⑤ Blind hem foot G ⑥ Automatic buttonhole foot R ⑦ Spool holder (large) (1 set on the machine) ⑧...
GETTING READY TO SEW Connecting the Power Supply ① Using the foot control Turn off the power switch. Insert the pin connector into the jack. Insert the machine plug into the power inlet. Insert the power supply plug into the wall outlet. Turn on the power switch.
Controlling Sewing Speed Speed control slider Sewing speed can be varied by the speed control slider according to your sewing needs. To increase sewing speed, move the slider to the right. To decrease sewing speed, move the slider to the left. Foot control Depress the foot control to start the machine.
Machine Operating Buttons ⑥ ⑤ ③ ④ ① Start/Stop button ② Press this button to start or stop the machine. The machine starts running slowly for the first few ① stitches, and it then runs at the speed set by the speed control slider.
Page 9
④ Needle up/down button ④ Press the needle up/down button to bring the needle up or down. The machine will stop with the needle up or down depending on the needle position determined by this button. ⑤ Cursor buttons ⑤ Use these buttons to move the cursor ⑦...
Presser Foot Lifter The presser foot lifter raises and lowers the presser foot. You can raise the foot about 1/4˝ (0.7 cm) higher than the normal up position for easy removal of the presser foot, or to help you place thick material under the foot. ①...
Dropping or Raising the Feed Dog ① ② The drop feed lever is located underneath the free arm bed on the back of the machine. To drop the feed dog, push the lever in the direction of the arrow ① . To raise the feed dog, push the lever in the direction of the arrow ②...
Setting the Spool of Thread Horizontal spool pin ② ① Lift up the spool pin. Place a spool of thread on the spool pin. Attach the large spool holder, and press it firmly against the spool of thread so that the spool rests on the supporter.
Winding the bobbin NOTE: Set the speed control slider at its fastest position for bobbin winding. ① Draw the thread from the spool and pass the thread around the bobbin winding tension disk. ① Bobbin winding tension disk Thread through the hole in the bobbin from the inside to the outside.
Page 14
Inserting the bobbin CAUTION: Turn OFF the power switch before inserting the bobbin and threading the bobbin holder. Place a bobbin in the bobbin holder with the thread ① running off counterclockwise. ① End of thread Guide the thread into the first notch ② on the front side of the bobbin holder.
Threading the Machine Raise the presser foot. Press the ① needle up/down button ① to raise ② the thread take-up lever to its highest position. ① Needle up/down button CAUTION: Turn OFF the power switch before threading the machine. Turn the power switch off. Draw the end of the thread around the upper thread guide.
Needle Threader CAUTION: Turn off the power switch when using the needle threader. Lower the presser foot. Raise the needle to its highest position. Pull down the needle threader knob as far as it will go. The hook comes out through the needle eye from behind.
Drawing up the Bobbin Thread Raise the presser foot. Hold the needle thread lightly with your left hand. Turn the power switch on. Press the needle up/down button twice to lower and raise the needle to pick up the bobbin thread. ①...
LCD Display The LCD display shows the following information when the machine is turned on. ① Identification letter for recommended foot ② Stitch pattern number ① ③ Cursors ④ Stitch width ⑤ Stitch length ② ③ ④ ⑤ Press the cursor buttons to move the cursor under the stitch pattern number.
Adjusting the Needle Thread Tension Straight stitch balanced tension The ideal straight stitch has threads locked between two ① layers of fabric, as illustrated (magnified to show detail). If you look at the top and bottom of the seam, notice that the stitches are evenly balanced.
Page 20
Zigzag stitch For an ideal zigzag stitch, the bobbin thread does not show on the right side (top side) of the fabric, and the needle thread shows slightly on the wrong side (bottom side) of the fabric. See the illustrations for the correct appearance. To match this appearance, adjust the needle tension as necessary.
BASIC SEWING ① ② ③ Straight Stitch Sewing ① Stitch pattern: 00 or 01 ② Thread tension dial: 2 to 6 ③ Presser foot: Zigzag foot A NOTE: When sewing with the satin stitch foot F or buttonhole foot R, pull the threads to the left to hold them. Starting to sew Raise presser foot and position the fabric next to a seam guide line on the needle plate.
Sewing from the Edge of Thick Fabric The black button ① on the zigzag foot locks the foot in the horizontal position. This is helpful when starting sewing from the far edge of thick fabrics ② or sewing across a hem. Lower the needle into the fabric at the point where you wish to start sewing.
Lock-a-matic Stitch ① ② ③ 00 01 02 03 04 05 06 07 08 09 ① Stitch pattern: ② Thread tension dial: 2 to 6 ③ Presser foot: Zigzag foot A 10 11 12 13 14 15 16 17 18 19 Use this stitch to secure the beginning and the end of a seam with backstitching.
Stretch Stitch ① ② ③ ① Stitch pattern: 04 or 05 (100-stitch model) 02 03 04 05 06 07 08 09 05 or 06 (20-stitch model) ② Thread tension dial: 3 to 6 ③ Presser foot: Zigzag foot A 00 01 02 03 04 05 06 07 08 09 This stitch is a narrow stretch stitch designed to 12 13 14 15 16 17 18 19 eliminate puckering on knit fabrics and bias seams, while...
Zigzag Stitch ① ② ③ ① Stitch pattern: 12 or 13 (100-stitch model) 0 11 12 13 14 15 16 17 18 19 07 (20-stitch model) ② Thread tension dial: 3 to 7 ③ Presser foot: Zigzag foot A 0 21 22 23 24 25 26 27 28 29 The zigzag stitch is one of the most useful and versatile stitches.
Overcasting with Zigzag Stitch ① ② ③ ① Stitch pattern: 12 (100-stitch model) 10 11 12 13 14 15 16 17 18 19 07 (20-stitch model) ② Thread tension dial: 3 to 7 ③ Presser foot: Overedge foot C This zigzag variation is very useful in garment construction and in finishing raw edges of any sewing 20 21 22 23 24 25 26 27 28 29 project.
Overedge Stitch ① ② ③ 15 16 17 18 19 ① Stitch pattern: 17 (100-stitch model) 13 (20-stitch model) ② Thread tension dial: 3 to 7 ③ Presser foot: Overedge foot C This stitch pattern combines the straight and the zigzag 25 26 27 28 29 stitches, using the overedge foot, to seam and overcast in one step.
Standard buttonhole ① ② ③ 3 04 05 06 07 08 09 ① Stitch pattern: 06 (100-stitch model) 10 (20-stitch model) ② Thread tension dial: 1 to 4 ③ Presser foot: Automatic buttonhole foot R 3 14 15 16 17 18 19 The size of a buttonhole is automatically set by placing a button in the rear of automatic buttonhole foot R.
Page 30
Lower the presser foot and pull the buttonhole lever down as far as it will go. ⑥ Buttonhole lever ⑥ ⑧ NOTE: The reference lines on the buttonhole foot can be ⑩ used as a positioning guide. Make sure there is no gap between the slider and ⑦...
Page 31
The buttonhole is sewn in the sequence as shown. When the buttonhole is finished, the machine will stop automatically with the needle in the up position. ⑬ Remove the fabric and place a pin just below the bartack to prevent accidentally cutting the stitches. Cut the opening with the seam ripper.
Rounded end buttonhole ① ② ③ 05 06 07 08 09 ① Stitch pattern: 07 (100-stitch model) 11 (20-stitch model) ② Thread tension dial: 1 to 4 ③ Presser foot: Automatic buttonhole foot R Sewing procedure is the same as standard buttonhole. 15 16 17 18 19 The buttonhole width can be varied from 2.5 to 5.5.
Corded Buttonhole ① ② ③ 3 04 05 06 07 08 09 ① Stitch pattern: 06 (100-stitch model) 10 (20-stitch model) ② Thread tension dial: 1 to 4 ③ Presser foot: Automatic buttonhole foot R 3 14 15 16 17 18 19 Use the same procedure as the standard buttonhole sewing.
Darning Stitch (100-stitch model only) ① ② ③ 07 08 09 ① Stitch pattern: ② Thread tension dial: 3 to 6 ③ Presser foot: Automatic buttonhole foot R 17 18 19 1 2 3 4 Starting to sew Attach the automatic buttonhole foot R and pull the button holder ①...
Tacking (100-stitch model only) ① ② ③ 10 11 12 13 14 15 16 17 18 19 ① Stitch pattern: ② Thread tension dial: 3 to 6 ③ Presser foot: Satin stitch foot F 20 21 22 23 24 25 26 27 28 29 Tacking is used to reinforce pockets, crotches and belt carriers where extra strength is needed.
Eyelet (100-stitch model only) 10 11 12 13 14 15 16 17 18 19 ① ② ③ ① Stitch pattern: ② Thread tension dial: 1 to 4 ③ Presser foot: Satin stitch foot F The eyelet is used for belt holes etc. 20 21 22 23 24 25 26 27 28 29 Starting to sew Lower the needle at the starting point and lower the...
Zipper Sewing ① ② ③ 00 01 02 03 04 05 06 07 08 09 ① Stitch pattern: ② Thread tension dial: 1 to 4 ③ Presser foot: Zigzag foot A Zipper foot E 10 11 12 13 14 15 16 17 18 19 Attaching the zipper foot Fit the pin on zipper foot E to the groove on the foot holder.
Page 38
Start sewing Fold back the left seam allowance. Turn the right seam ④ allowance under to form a 1/8˝ (0.2-0.3 cm) margin. Place the zipper teeth next to the fold and pin in place. Set the stitch length and thread tension back to the ②...
Page 39
Close the zipper and spread the fabric open flat with the right side facing up. Attach the Zigzag foot A. Adjust the stitch length to 5.0, stitch width to 3.5 (default value) and the thread tension dial to 1. Baste the opened fabric and zipper tape together. ⑧...
Blind Hemming ① ② ③ 16 17 18 19 ① Stitch pattern: 18 (100-stitch model) 14 (20-stitch model) ② Thread tension dial: 1 to 4 ③ Presser foot: Blind Hem foot G 26 27 28 29 Fold a hem with the wrong side of the fabric up to form a 1/4˝...
8 39 40 41 42 43 F A F F A F 50 51 52 53 54 55 56 57 Applique F A F ① ② ③ ① Stitch pattern: 52 (100-stitch model) 18 (20-stitch model) 2 53 54 55 56 57 ②...
F A F F A F Fringing ② ① ③ 0 51 52 53 54 55 56 57 ① Stitch pattern: 52 - 54 (100-stitch model) 18 (20-stitch model) ② Thread tension dial: 1 to 4 ③ Presser foot: Satin stitch foot F Fringing adds a special touch on table linens and shawls.
Decorative Stitches (100-stitch model only) ② ① 73 74 75 76 77 78 79 ③ 70 81 82 83 84 85 ① Stitch pattern: ② Thread tension dial: 3 to 6 ③ Presser foot: Satin stitch foot F * The stitch patterns 76-92 can also be used. For the best sewing results, carefully align and guide the 87 88 89 90 91 92 93 94 95 96 97 98 99...
CARE OF YOUR MACHINE Cleaning the Hook Race and Feed Dog WARNING: ① ③ Turn the power switch off and unplug the machine before cleaning. Do not dismantle the machine other than as explained in this section. ② CAUTION: Do not store the machine in a high-humidity area, near a heat radiator, or in direct sunlight.
Problems and Warning Signals If a buzzer sounds and the LCD screen shows a warning sign, follow the guidance below. Warning Sign Cause Try this 1. The start/stop button is pressed with the foot control Disconnect the foot control. connected. Contact the service center 2.
Troubleshooting Condition Cause Reference The needle thread 1. The needle thread is not threaded properly. Page 13 breaks 2. The needle thread tension is too tight. Page 17-18 3. The needle is bent or blunt. Page 9 4. The needle is incorrectly inserted. Page 9 5.
Introduction of optional accessory parts Make your home sewing more pleasant! Please purchase the following items in the shop where you buy our products. ● Quilt presser foot (Transparent zigzag type) It is used for free-motion quilting. Zigzag stitch is also possible with this presser foot. ●...
Page 56
2-11-1, TSURUMAKI, TAMA-SHI, TOKYO, 206-8551, JAPAN PHONE : (81)42-357-2341 FAX : (81)42-357-2379 Copyright 2015 JUKI CORPORATION All rights reserved throughout the world. 001015 40168851 / 808850540...