Lincoln Electric IDEALARC DC-600 Operating Manual page 9

SEE MACHINE RATING PLATE FOR REQUIRED INPUT SUPPLY VOLTAGE
L3
LINES
L2
INPUT
L1
GND
CONNECTION FOR HIGHEST RATING PLATE VOLTAGE, 50 OR 60 HZ.
LINK
L3
LINES
L2
INPUT
L1
H1
GND
H5
H3
CONNECTION FOR LOWEST RATING PLATE VOLTAGE, 50 OR 60 HZ.
LINK
L3
LINES
L2
INPUT
L1
GND
H3
H5
LINK
L3
LINES
L2
INPUT
L1
GND
H4
H5
LINK
L3
LINES
L2
INPUT
L1
GND
H3
H5
LINK
L3
LINES
L2
INPUT
L1
GND
H2
H5
Reconnect Panel Board Positions for 380/550 and 380/575 Voltage Machines
CONNECTION FOR HIGHEST RATING PLATE VOLTAGE, 50 OR 60 HZ.
LINK
L3
LINES
L2
INPUT
L1
H1
GND
H3
CONNECTION FOR LOWEST RATING PLATE VOLTAGE, 50 OR 60 HZ.
LINK
L3
LINES
L2
INPUT
L1
GND
H2
IMA 607A
Reconnect Panel Board Positions for Single Voltage Machines
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
CRI
W
2. CONNECT TERMINAL MARKED
V
3. CONNECT THE L1, L2, & L3 INPUT SUPPLY LINES TO INPUT SIDE OF THE CRI CONTACTOR AS SHOWN.
CONTACTOR
U
Reconnect Panel Board Positions for 380/500 VAC Machines
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
CRI
W 13
2. DISCONNECT AND INSULATE THE H2,
LEAST 600 VOLT INSULATION.
14
V
3. CONNECT L1, L2 & L3 INPUT SUPPLY LINES H1 AND H5 TRANSFORMER LEADS TO THE INPUT SIDE OF
CONTACTOR
15
U
THE CRI CONTACTOR AS SHOWN.
H4
4. CONNECT TERMINAL MARKED
5. MOUNT THE LINKS IN THE POSITIONS SHOWN WITH THE PROVIDED HEX NUTS,
H2
DOUBLE UP THE LINKS IN TWO OF THE POSITIONS TO SAVE THEM FOR FUTURE USE. SECURE THE
PILOT
REMAINING HEX NUTS IN PLACE.
TRANSF
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
CRI 1
W
2. DISCONNECT AND INSULATE TH
LEAST 600 VOLT INSULATION.
2
V
3. CONNECT L1, L2 & L3 INPUT SUPPLY LINES H1 AND H3 TRANSFORMER LEADS TO THE INPUT SIDE OF
CONTACTOR
3
U
THE CRI CONTACTOR AS SHOWN.
4. CONNECT TERMINAL MARKED
H4
H1
5. MOUNT THE LINKS IN THE POSITIONS SHOWN WITH THE PROVIDED HEX NUTS.
H2
PILOT
TRANSF
Reconnect Panel Board Positions for 220/380/440 VAC Machines
CONNECTION FOR 440 VOLTS 50 OR 60 HZ. (460V 60HZ)
CRI
W
V
CONTACTOR
U
H3
H1
H2
PILOT
TRANSF
CONNECTION FOR 380 VOLTS, 50 OR 60 HZ.
CRI
W
V
CONTACTOR
U
H4
H1
H2
PILOT
TRANSF
CONNECTION FOR 220 VOLTS, 50 OR 60 HZ.
CRI
W
V
CONTACTOR
U
H4
H1
H3
PILOT
TRANSF
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
CRI 13
W
2. DISCONNECT AND INSULATE THE H2, LEAD TERMINAL WITH TAPE TO PROVIDE AT
LEAST 600 VOLT INSULATION.
14
V
CONTACTOR 3. CONNECT L1, L2 & L3 INPUT SUPPLY LINES H1 AND H3 TRANSFORMER LEADS TO THE INPUT SIDE OF
15
U
THE CRI CONTACTOR AS SHOWN.
H2 4. CONNECT TERMINAL MARKED
5. MOUNT THE LINKS IN THE POSITIONS SHOWN WITH THE PROVIDED HEX NUTS,
DOUBLE UP THE LINKS IN TWO OF THE POSITIONS TO SAVE THEM FOR FUTURE USE. SECURE THE
PILOT
REMAINING HEX NUTS IN PLACE.
TRANSF
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
CRI
W 1
2. DISCONNECT AND INSULATE TH
LEAST 600 VOLT INSULATION.
2
V
3. CONNECT L1, L2 & L3 INPUT SUPPLY LINES H1 AND H2 TRANSFORMER LEADS TO THE INPUT SIDE OF
CONTACTOR
3
U
THE CRI CONTACTOR AS SHOWN.
4. CONNECT TERMINAL MARKED
H3
H1
5. MOUNT THE LINKS IN THE POSITIONS SHOWN WITH THE PROVIDED HEX NUTS.
PILOT
TRANSF
Idealarc DC-600
Figure A.4
TO GROUND PER NATIONAL ELECTRIC CODES.
Figure A.5
H3 & H4 LEAD TERMINAL WITH TAPE TO PROVIDE AT
TO GROUND PER LOCAL AND NATIONAL ELECTRIC CODES.
E H2, H4 & H 5LE AD TERMINAL WITH TAPE TO PROVIDE
TO GROUND PER LOCAL AND NATIONAL ELECTRIC CODES.
Figure A.6
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
2. DISCONNECT AND INSULATE THE H2,H3 & H5 LEAD TERMINALS SEPARA
LEAST 600 VOLT INSULATION.
3. CONNECT L1, L2 & L3 INPUT SUPPLY LINES H1 AND H4 CONTROL TRANSFORMER LEADS TO THE
INPUT SIDE OF THE CRI CONTRACTOR AS SHOWN.
4. CONNECT TERMINAL MARKED TO GROUND PER LOCAL AND NATIONAL ELECTRIC CODES.
5. MOUNT THE LINKS IN THE POSITIONS SHOWN: DOUBLE OR TRIPLE STACK THE LINKS IN THREE
POSITIONS. CONNECT THE FLEX LEAD AS SHOWN: POSITIONING THE LUGS TO MAINTAIN MAXIMUM
CLEARANCE TO THE LINKS. INSTALL AND TIGHTEN ALL OF THE HEX NUTS.
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
2. DISCONNECT AND INSULATE TH E H2, H4 & H5 LE AD TERMINALS SEPARATELY WITH TAPE TO PROVIDE AT
LEAST 600 VOLT INSULATION.
3. CONNECT L1, L2 & L3 INPUT SUPPLY LINES H1 AND H3 CONTROL TRANSFORMER LEADS TO THE
INPUT SIDE OF THE CRI CONTACTOR AS SHOWN.
4. CONNECT TERMINAL MARKED TO GROUND PER LOCAL AND NATIONAL ELECTRIC CODES.
5. MOUNT THE LINKS IN THE POSITIONS SHOWN: DOUBLE UP THE LINKS IN TWO OF THE POSITIONS,
LOOP THE POSITIONS. INSTALL AND TIGHTEN ALL OF THE HEX NUTS.
1. TURN OFF THE INPUT POWER USING THE DISCONNECT SWITCH AT THE FUSE BOX
2. DISCONNECT AND INSULATE THE H3, H4 & H5 LEAD TERMINALS SEPARATE L Y WITH TAPE TO PROVIDE AT
LEAST 600 VOLT INSULATION.
3. CONNECT L1, L2 & L3 INPUT SUPPLY LINES H1 AND H2 CONTROL TRANSFORMER LEADS TO THE
INPUT SIDE OF THE CRI CONTACTOR AS SHOWN.
4. CONNECT TERMINAL MARKED TO GROUND PER LOCAL AND NATIONAL ELECTRIC CODES.
5. MOUNT THE LINKS IN THE POSITIONS SHOWN. LOOP THE FLEX LEAD IN THE POSITION SHOWN.
INSTALL AND TIGHTEN ALL OF THE HEX NUTS.
Figure A.7
TO GROUND PER LOCAL AND NATIONAL ELECTRIC CODES.
E H3, LE AD TERMINAL WITH TAPE TO PROVIDE AT
TO GROUND PER LOCAL AND NATIONAL ELECTRIC CODES.
AT
T ELY WITH TAPE TO PROVIDE AT
Page 9