Epson EB-460i Installation Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Projector
  5. EB-460I
  6. Installation manual
Epson EB-460i Installation Manual

Epson EB-460i Installation Manual

Hide thumbs Also See for EB-460i:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Installation Guide

Advertisement

Table of Contents
loading

Related Manuals for Epson EB-460i

Summary of Contents for Epson EB-460i

  • Page 1 Installation Guide...

  • Page 2: Safety Instructions

    Install the setting plate so that it can sufficiently support the mass of the projector and setting plate, and resist any horizontal vibration. Use M8 nuts and bolts. Nuts and bolts smaller than M8 could cause the setting plate to fall. Epson takes no responsibility for any damage or injury caused by incorrect installation.

  • Page 3: Place To Install The Setting Plate

    Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical components from becoming dirty. About This Installation Guide This guide describes how to mount the short-throw projector EB-460i/460/450Wi/450W/440W to a wall using the exclusive setting plate.
  • Page 4 Package Contents s Page 5 Specifications s Page 6 Connecting Devices s Page 7 Projection Distance Table s Page 8 Installation Procedure s Page 11 (1) Install the wall plate on the wall (2) Determine the projection distance and pull out the slider (3) Attach the setting plate to the wall plate (4) Secure the projector to the setting plate (5) Connect the power cable and other cables to the projector...

  • Page 5: Package Contents

    1. Package Contents Wall plate Setting plate End cap Wall plate cover Template sheet Hexagon wrenches (for M4, M5, and M8) (for installing the wall plate) Shape Name Quantity Application M8 x 15 mm hexagon socket head cap bolt with For installing setting plate washer M5 x 12 mm hexagon socket head cap bolt with...

  • Page 6: Specifications

    2. Specifications Item Specification Remark Reference Page Setting plate mass Approx. 6.3 kg Wall plate (2.2 kg [4.85 lb.]) (13.89 lb.) Covers and cap (0.47 kg [1.04 lb.]) Forward/backward slide 0 to 300 mm Refer to the figure adjustment range (11.81 in.) below °...

  • Page 7: Connecting Devices

    3.Connecting Devices Prepare a power cable, computer cable, USB cable, and so on at the location where the setting plate is to be installed. Prepare all necessary cables for devices, such as a document camera or microphone, that you will connect to the projector.

  • Page 8: Projection Distance Table

    4. Projection Distance Table Refer to the table below and install the setting plate and projector to project images at an appropriate size on the projection surface. The values are only rough estimates. The recommended range for the projection distance (a) is 7 to 37 cm (2.76 to 14.57 in.). Offset value for the position of 65 mm (2.55 in.) the center of the screen and the...
  • Page 9 Unit: mm (in.) Screen Projection Distance Height of Interactive Aspect Ratio Size Distance Between Projection Whiteboard Minimum Projection Surface (Wide) Surface and Wall Plate 63" 1280x960 71 (2.80) 175 (6.89) 960 (37.80) Hitachi StarBoard FX-63 (50.39x37.79) 64" 1300x970 79 (3.11) 177 (6.97) 975 (38.39) SMART Board 660...
  • Page 10 Screen Projection Distance Height of Interactive Aspect Ratio Size Distance Between Projection Whiteboard Minimum Projection Surface (Wide) Surface and Wall Plate 16:9 58" 1280x720 73 (2.87) 295 (11.61) 722 (28.43) (50.39x28.34) 60" 1330x750 90 (3.54) 304 (11.97) 747 (29.41) RM ClassBoard2 60 (52.36x29.52) 65"...

  • Page 11: Installation Procedure

    5. Installation Procedure Make sure to follow the steps below to install the setting plate. If you ignore these steps, the setting plate could fall and cause personal injury or property damage. The maximum combined mass of the setting plate and the projector is approximately 15.2 kg (33.5 lb).

  • Page 12: Determine The Projection Distance And Pull Out The Slider

    M8 could cause the setting plate to fall. ❏ Epson takes no responsibility for any damage or injury caused by incorrect installation. Determine the projection distance and pull out the slider (1) From the projection distance table, calculate the distance (a) from the projection surface to the front of the projector.

  • Page 13: Attach The Setting Plate To The Wall Plate

    Attach the setting plate to the wall plate (1) Hang the setting plate hook onto the wall plate bar ( (2) Lift up the setting plate and pass the cables through it ( Caution Take care not to trap the cables between the setting plate and wall plate. (3) Tighten the two M8 x 15 mm hexagon socket head cap bolts and two M8 x 35 mm hexagon socket head cap bolts supplied with the setting plate so that the setting plate becomes vertical against the wall (...
  • Page 14 (2) Insert the slide plate into the setting plate from the interface side of the projector ( Align the marks on the projector and the setting plate ( M5 x 12 mm hexagon socket head cap bolts (2) Slide plate Bolt positions Projector interface side...

  • Page 15: Adjusting The Projection Screen

    6. Adjusting the Projection Screen To ensure maximum projection screen quality, follow the steps below to adjust the projection screen. Do not make adjustments with the Keystone function of the projector. Doing so may result in a reduction in image quality. Turn on the projector Using Remote Control Using Control Panel...

  • Page 16: Adjust The Focus

    Adjust the focus (1) Move the air filter cover lever to open the air filter cover. (2) Use the focus lever to adjust the focus. Air filter cover Focus lever (3) After you finish making the adjustment, close the air filter cover. Use the top adjustment dial to adjust the vertical tilt Repeat steps as necessary.
  • Page 17 Use the right adjustment dial to adjust the horizontal rotation (1) Loosen the two screws that correspond to the right adjustment dial ( (2) Turn the adjustment dial to adjust the horizontal rotation ( (3) After you finish making all of the adjustments in steps , tighten the two screws you loosened in Use the left adjustment dial to adjust the horizontal roll...

  • Page 18: Adjust The Vertical Slide

    Adjust the vertical slide Adjust the vertical slide with the two M8 x 35 mm hexagon socket head cap bolts at the bottom of the setting plate. Tightening the bolts raises the setting plate, and loosening them lowers it. The projection screen is raised or lowered accordingly. M8 x 35 mm hexagon socket head cap bolts (2)

  • Page 19: Attaching The Covers

    7. Attaching the Covers Attach the wall plate cover and end cap (1) Secure the wall plate cover with the two M4 x 12 mm hexagon socket head cap bolts ( Depending on how the cables are wired, you may need to cut out parts of the wall plate cover to allow the cables to be passed through it.

  • Page 20: Using The Easy Interactive Function

    8. Appendix Using the Easy Interactive Function After you install an Easy Interactive Function compatible model (EB-460i/450Wi), you need to install the Easy Interactive Driver and perform calibration (to align the positions of the cursor and Easy Interactive Pen). For details, refer to the supplied Quick Start Guide or the User’s Guide on the Document CD-ROM.

This manual is also suitable for:

Eb-460Eb-450wEb-440wEb-450wi

Table of Contents