Nxd-1000Vi Specifications - AMX NXD-1000Vi Operation/Reference Manual

NXD-1000Vi Specifications

The following table outlines the specifications for the 10" Widescreen Modero panels.
Product Specifications
Dimensions (HWD):
Power Requirements
(stand-alone NXD-1000Vi):
Memory (factory default):
Weight (stand-alone):
Certifications:
Panel LCD Parameters:
Active Viewing Area:
IR Reception Angle:
Supported Audio Sample
Rates:
Front Panel Components:
Light sensor:
Motion sensor (PIR):
IR Receiver:
Front setup access button:
NXD-1000Vi 10" Modero® Wall/Flush Mount Touch Panel with Intercom
• NXA-RK10(optional): metal rack-mount with black matte finish:
(5 RU - rack units high)
8.72" x 19.0" x 0.50" (22.15 cm x 48.26 cm x 1.27 cm)
• NXD-1000Vi (with faceplate): 7.96" x 11.16" x 3.32"
(20.22 cm x 28.34 cm x 8.43 cm)
• CB-TP10 Conduit/Wallbox (optional): 9.23" x 10.90" x 3.40"
(23.44 cm x 27.69 cm x 8.64 cm)
• Constant current draw: 1.1 A @ 12 VDC
• Startup current draw: 1.6 A @ 12 VDC
• 64 MB SDRAM
• 128 MB Compact Flash (upgradeable to 1 GB - factory programmed)
2.65 lbs (1.20 kg)
• FCC Part 15 Class B and CE
• IEC60950
• Aspect ratio: 16 x 9
• Brightness (luminance): 350 cd/m
• Channel transparency: 8-bit Alpha blending
• Contrast ratio: 250:1
• Display colors: 256 thousand colors (18-bit color depth)
• Dot/pixel pitch: 0.28 mm
• Panel type: TFT Color Active-Matrix
• Screen resolution: 800 x 480 pixels (HV) @ 60 Hz frame frequency
• Video format: NTSC, PAL, and SECAM
• Viewing angle (95° total viewing angle):
Vertical: + 45° (up from center) and - 65° (down from center)
• 8.74" x 5.24" (22.20cm x 13.32cm)
• Horizontal: + 50° (left and right from center)
• Vertical: + 30° (up and down from center)
• 48000Hz, 44100Hz, 32000Hz, 24000Hz, 22050Hz, 16000Hz, 12000Hz,
11025Hz, and 8000Hz.
• Photosensitive light detector for automatic adjustment of the panel brightness
(a dim room results in a dimmer LCD display, and a bright room results in a
brighter LCD display).
Note: The light sensor can be adjusted via the Sensor Setup page (page 107).
• Proximity Infrared Detector to wake the panel when the panel is approached.
• Activation range: + 45° (left and right from center) and + 20° (up and down
from center).
Note: This sensor can be adjusted via the Sensor Setup page (see page 107).
• IR reception: 38 KHz IR frequency.
• The IR receiver is located beneath the translucent Front Setup button. When
an IR code is detected it is sent to the NetLinx Master as a push on the
appropriate AMX IR channel.
• IR receivers and transmitters on G4 panels share the device address number
of the panel.
• Provides both access to the Setup and Calibration page and toggles the
panel between a "sleep" or "wake" state.
- When wired, "sleep" status means the backlight is Off.
- When battery operated, wireless "sleep" status means the touch panel
base is either Off or "suspended".
2
Introduction
3