READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 7 AND 8. Broan-NuTone LLC; Hartford, Wisconsin www.broan.com 800-558-1711 Broan-NuTone Canada; Mississauga, Ontario www.broan.ca 877-896-1119 REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register V06112 rev. I...
Page 2
WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC TO REDUCE THE RISK OF INJURY TO PERSONS SHOCK OR INJURY TO PERSONS, OBSERVE IN THE EVENT OF A RANGE TOP GREASE THE FOLLOWING: FIRE, OBSERVE THE FOLLOWING*: Use this unit only in the manner intended by the SMOTHER FLAMES with a close-fitting lid, manufacturer.
This warranty supersedes all prior warranties. To qualify for warranty service, you must (a) notify Broan-NuTone LLC at the addresses or telephone number stated below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part.
1. INSTALL DUCTWORK Plan where and how the ductwork will be installed. Install proper-sized ductwork, elbows and roof or wall cap. Use 2” duct tape to seal duct joints. The minimum hood distance above cooktop must not be less than 24”. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities.
2. PREPARE THE INSTALLATION (CONT’D) Cut-out the openings for duct (A) and power cable (B), in cabinet or wall, according to the direction of discharge chosen. See figures below. NOTE: The duct opening width (A on figures below) is 10½”, centered. ORIZONTAL DISCHARGE ERTICAL DISCHARGE CABINET BOTTOM...
Page 6
3. PREPARE THE HOOD (CONT’D) ERTICAL ISCHARGE The hood is set up at the factory for vertical discharge. Go to step 4 on page 7. Start on step 4.4. ORIZONTAL ISCHARGE 3.4 From inside the hood, unfold the small retaining tab (A) (located on the edge of the blower opening) on the air diffuser edge.
4. INSTALL THE ADAPTER/DAMPER The wall duct must be roughed-in to properly interface with the hood. Before performing the installation, make sure the adapter fits easily in the duct. If this hood replaces an existing hood, please note that location of the air exhaust can vary from one hood manufacturer to another.
5. INSTALL THE HOOD 5.1 Run power cable to installation location. Position the hood in its intended location. Using a pen, mark the position of the screws (smaller part of the keyholes, see pictures below for the (5) keyholes locations). Remove the hood. 5.2 Install (4) no.
7. REINSTALL BOTTOM PANEL Reinstall the bottom panel, using 5 screws saved from step 3, as shown beside. Reinstall filters. CAUTION Remove protective plastic film covering filters before installing them. HD0124 8. LIGHT BULBS This hood must use 120 V, 50 W max., type MR16, GU10 shielded halogen lamps. (Purchase separately). WARNING In order to prevent the risk of personal injury, do not install a lamp identified for use only in enclosed fixtures.
9. OPERATION Always turn your blower on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. HC0016 A) Blower Delay switch D) OFF lighting B) ON blower / Speed control switch E) Halogen light switch...
10. USE AND CARE Grease filters and bottom panel. The grease filters and the bottom panel should be cleaned frequently. Use a warm detergent solution. Remove grease filters by pushing them towards the back of hood and rotating downward. Clean all-metal filters in the diswasher using a non-phophate detergent. Discoloration of the filter may occur if using phosphate detergents, or as a result of local water conditions —...