Epson L1300 Start Here

EN TH

Start Here

TC
安裝說明
© 2013 Seiko Epson Corporation.
All rights reserved.
Printed in XXXXXX
Read This First / 請先閱讀本說明 /
This product requires careful handling of ink. Ink may splatter when the ink
tanks are filled or refilled with ink. If ink gets on your clothes or belongings,
it may not come off.
請小心處理本產品的墨水。當將墨水裝入或填充至大容量墨水槽時，
墨水可能會濺灑出。如果墨水滴到您的衣物或物品，可能會無法清除
乾淨。
c
Important; must be observed to avoid damage to your equipment.
重要事項：務必遵守重要事項說明，避免您的設備受損。
1
L1300
L1800
Windows
Contents may vary by location.
內容可能因地點而有不同。
Remove all protective materials.
移除保護膠帶。
Q
Do not open the initial setup ink bottle package or the refill ink
bottle package until you are ready to fill the ink tank. The ink bottle
is vacuum packed to maintain its reliability.
若不填充至大容量墨水槽，請勿拆開初始設定墨水瓶的包裝或填
充墨水瓶的包裝。為了維持墨水瓶列印穩定性，墨水瓶是以真空
包裝的。
2
Unhook.
A
取下大容量墨水槽，並將其平放。
Q
O Do not pull the tubes.
O 請勿拉扯墨水導管。 O
O
B
Open and remove.
打開大容量墨水槽護蓋並拔下瓶蓋。
c
O Use the ink bottles that came with your product.
O Even if some ink bottles are dented, the quality and quantity of ink
are guaranteed, and they can be used safely.
O Epson cannot guarantee the quality or reliability of non-genuine
ink. The use of non-genuine ink may cause damage that is not
covered by Epson's warranties.
O 請使用印表機內附的墨水瓶。 O
O 即使部分墨水瓶出現凹痕，也不會影響墨水品質及墨水量，可 O
安全使用。
O Epson 不保證非原廠墨水的品質或可靠性。使用非原廠墨水而
導致損壞，Epson 將不提供免費的保固服務。
O
O
O
C
Snap off, remove, and then close.
拔下墨水瓶蓋上的栓子，打開瓶蓋並移除封條，然後裝回瓶蓋。
c
Close the ink bottle cap tightly; otherwise
ink may leak.
請拴緊墨水瓶蓋，否則墨水可能會漏出。
D
Match the ink color with the tank, and then fill with all of the ink.
確定墨水顏色與大容量墨水槽相符，然後裝入所有墨水。
Q
Install.
使用栓子密封住墨水瓶。
E
Close securely.
將大容量墨水槽瓶蓋牢牢拴緊。
F
Repeat steps B to E for each ink bottle.
重覆步驟OBO至OE，裝入其他顏色的墨水。
G
Close.
闔上大容量墨水槽護蓋。
H
Hook the tank onto the product.
將大容量墨水槽掛回印表機。
c
Make sure to hook the tank unit before printing. Do not lay the unit
down, or position it higher or lower than the product.
在開始列印前，務必掛回大容量墨水槽。請勿將其平放，或放置
在高於或低於印表機的位置。
I
Connect and plug in.
連接電源線並插入電源插座。
J
Turn product on and wait until lamp stops flashing.
開啟印表機電源，並等到燈號停止閃爍。
K
Check position.
檢查位置。
L
Press H for 3 seconds until P starts flashing. Charging ink takes about 22
minutes. Wait until the light stays on.
按住OHO3 秒，直到OPO開始閃爍。墨水設定大約需要 22 分鐘。請等待燈號
亮起。
M
Install the Epson applications.
安裝 Epson 應用程式。
c
Do not connect a USB cable unless
instructed to do so.
除非有指示要求，否則請勿連接 USBO
連接線。
Windows
Insert the CD, and then follow the on-screen
instructions.
放入軟體光碟，並依照螢幕上的指示操作。
Windows (No CD/DVD drive)
Mac OS X
Visit the Epson website to install the applications.
請瀏覽 Epson 網站以安裝應用程式。
http://support.epson.net/setupnavi/