Panasonic AJ-SDa755E Operating Instructions Manual page 49

CONTENTS
Setup menus
USER menu
<AUDIO>
No./Item
728 This selects whether to superimpose the
audio data onto the SDI output.
EMBEDDED
AUD 0000 OFF : Data is not superimposed.
0001 ON : Data is superimposed.
<Note>
When no optional board (AJ-YA755G) has been
installed, setup menu No. 728 is not displayed.
731 This selects whether or not the cue signal is
to be output to the main line output in the
CUE OUT SEL search mode.
0000 OFF : CUE is not output.
0001 ON : CUE is output.
<Notes>
OThis function works only when a setting
other than MANU has been selected by
setup menu No. 721 (MONI CH SEL).
OThe main signal system output channels
used for the CUE output differ depending on
the setting selected by setup menu No. 735
(MON AUTO SEL).
When L/R is selected:
CUE is output to CH1 and CH2.
When L is selected:
CUE is output to CH1.
When R is selected:
CUE is output to CH2.
OWhen PCM has been selected as the setup
menu No. 721 (MONI CH SEL) setting, PCM
is output.
The underlined items indicates the initial setting.
<Concerning the CUE output in the search mode>
The table below shows how the CUE output to the monitor and main signal system outputs differs according
to how the setup menu item (No. 721, No. 731 and No. 735) settings are combined.
731 721
CUE OUT MONI CH MON AUTO
SEL SEL
MANU
OFF AUTO
PCM
MANU
ON AUTO
PCM
<Notes>
21: PCM audio signal output is muted when the VTR is played outside the –0.43 to +1 normal speed.
22: PCM audio signal output is muted when the VTR is played outside the –10 to +10 normal speed.
When either AUTO is selected, the PCM audio signal is output within –0.43 to +1 normal speed even in
the automatic CUE output mode.
Description
735
Monitor output
Lch Rch
SEL
----------
PCM PCM
21
L/R CUE CUE
CUE
L PCM
R PCM CUE
21
----------
PCM PCM
22
----------
PCM PCM
21
L/R CUE CUE
L CUE
PCM
R PCM CUE
21
----------
PCM PCM
22
No./Item
733 This selects the timing for the output picture and
CUE output when CUE has been selected for
monitor output.
CUE OUT
0000 NORMAL : The timing is aligned with the
0001 DIRECT : Whatever has been recorded on
<Note>
When DIRECT has been selected, the timing of the
output picture and that of the cue output are not
aligned properly.
734 This selects whether the operation of the
MONITOR SELECT button on the front panel is to
be enabled or disabled.
MONI SEL INH
0000 OFF : Operation is enabled.
0001
0002 ON1 :
Operation is disabled in the FULL display mode
and enabled only in the FINE display mode.
735 Although CUE is automatically output to the
monitor output in accordance with the operation
mode when a setting AUTO has been selected by
MON AUTO
setup menu item No. 721 (MONI CH SEL), the
SEL
MON AUTO SEL setup menu item is used to
select the monitor channel which is to be
automatically switched to CUE.
0000
CUE is output to both the left and right channels.
0001
CUE is output to the left channel only.
0002
CUE is output to the right channel only.
Main signal system output
CH1 CH2
21
PCM PCM
21 21
21
PCM PCM
22 22 22
PCM PCM
21 21 21
CUE CUE
CUE
PCM
21 21
CUE
PCM
21
PCM PCM
22 22 22
Description
output picture.
the tape is output with no delay.
ON : Operation is disabled.
L/R :
L :
R :
49 (E)