Yamaha DSP-AX1600 Service Manual page 26

Table of Contents

Advertisement

RX-V1600/DSP-AX1600
• Starting DIAG
Press the "MASTER ON/OFF" key while simultaneously
pressing those two keys of the main unit as indicated in the
figure below.
Keys of main unit
Turn on the power while pressing these keys.
これらのキーを同時に押しながら、パワーオンする。
• Starting DIAG in the protection cancel
mode
If the protection function works and causes hindrance to
trouble diagnosis, cancel the protection function as de-
scribed below, and it will be possible to enter the DIAG
mode. (The protection functions other than the excess cur-
rent detect function will be disabled.)
Press the "MASTER ON/OFF" key while simultaneously
pressing those two keys indicated in the figure above. At
this time, keep pressing those two keys for 3 seconds or
longer.
In this mode, the "SLEEP" segment of the FL display of the
main unit flashes to indicate that the mode is DIAG mode
with the protection functions disabled.
CAUTION!
Using this product with the protection function disabled
may cause damage to itself. Use special care for this
point when using this mode.
• Canceling DIAG
1 Before canceling DIAG, execute setting for PRESET of
DIAG menu No.11 (Memory initialization inhibited or
Memory initialized).
* In order to keep the user memory stored, be sure to
select PRESET INHIBIT (Memory initialization inhib-
ited). Any protection history will remain in memory.
2 Turn off the power by pressing the "MASTER ON/OFF"
key of the main unit or the "STANDBY" key of the re-
mote control.
26
● ダイアグの起動
本機の下図に示すキーを同時に押しながら "MASTER ON/
OFF" キーを押すと、ダイアグが起動します。
/ 本機キー
● プロテクション解除モードでの起動
プロテクションが動作することにより、故障箇所の診断に
支障をきたすような場合は、次の方法によりプロテクショ
ンを解除した状態でダイアグモードに入ることができま
す。 (過電流検出以外のプロテクション動作を解除する)
上図のキーを同時に押しながら "MASTER ON/OFF" キーを
押します。このとき、上図のキーを3秒以上押し続けてく
ださい。
このモードでは本機FLの "SLEEP" セグメントが点滅し、
プロテクションを解除した状態でのダイアグモードである
ことを知らせます。
注意!
プロテクションを解除した状態でのダイアグモードは、
危険な状態でもプロテクションが作動しないため、動作
させると、機器を破壊することがあります。このモード
を使用する場合は十分注意してください。
● ダイアグの解除
① ダイアグを解除する前に、ダイアグメニューNo.11の
FACTORY PRESET (メモリーの初期化禁止/またはメ
モリーの初期化) の設定をします。
※ ユ ー ザ ー メ モ リ ー を 保 持 し た い 場 合 は 、 必 ず
PRESET INHIBIT (メモリー初期化禁止) を選択して
ください。
② 本機の "MASTER ON/OFF" キーかリモコンの "STANDBY"
キーを押し、パワーオフにします。
• Display provided when DIAG started
The FL display of the main unit displays the protection
function history data and the version (1 alphabet) and the
DIAG menu (sub-menu MARGIN of DIAG menu No.1
DA60Y-YSS930) a few seconds later.
When there is no history of protection function:
Opening message /
オープニング表示
When there is no history
of protection function
Version (1 alphabet)
プロテクション履歴が
バージョン (英1文字)
ない場合
When there is a history of protection function:
When there is a history of protection
function due to excess current
過電流によるプロテクション
履歴がある場合
Cause: An excessive current flowed through the power
amplifier.
Turning on the power without correcting the abnormality
will cause the protection function to work immediately and
the power supply will instantly be shut off.
Note)
• Applying the power to a unit without correcting the
abnormality can be dangerous and cause additional
circuit damage.
• The output transistors in each amplifier channel
should be checked for damage before applying any
power.
• Amplifier current should be monitored by measuring
across the emitter resistors for each channel.
● ダイアグ起動時の表示
本機のFLディスプレイにプロテクション履歴情報とバー
ジョン (英1文字) が表示され、数秒後にダイアグメニュー
(No.1 DA60Y-YSS930のサブメニューMARGIN) になりま
す。
プロテクション履歴がない場合:
DIAG menu display /
ダイアグメニュー表示
After a few seconds
数秒後
プロテクション履歴がある場合:
Version (1 alphabet)
バージョン (英1文字)
原因: パワーアンプに過電流が流れた。
補足: パワートランジスタの電流を検出していますので、
電流検出トランジスタをチェックすれば異常チャン
ネルが特定できます。
異常状態のままパワーオンすると、瞬時にプロテクション
がかかり、すぐに電源が切れます。

Advertisement

Table of Contents
loading

This manual is also suitable for:

Rx-v1600

Table of Contents