Yaesu FT-2000 Technical Supplement page 31

Rotate the [MIC] knob to the fully counter-clock-
wise position.
Press the PTT switch, then gently rotate the [MIC]
knob to the fully clockwise position.
Rotate the [SUB(VFO-B)] knob for 115 W (+5W/–
0W) on the Wattmeter.
Release the PTT switch.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d15 iAL"for the 24 MHz
amateur band´s ALC Adjustment, then rotate the
[SUB(VFO-B)] knob so that the VFO-B frequency
display shows "0020."
Rotate the [MIC] knob to the fully counter-clock-
wise position.
Press the PTT switch, then gently rotate the [MIC]
knob to the fully clockwise position.
Rotate the [SUB(VFO-B)] knob for 100 W (+5W/–
0W) on the Wattmeter, then rotate the [SUB(VFO-
B)] knob so that the VFO-B frequency indication
"10" increase.
Release the PTT switch.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d16 iAL"for the 28 MHz
amateur band´s ALC Adjustment, then rotate the
[SUB(VFO-B)] knob so that the VFO-B frequency
display shows "0020."
Rotate the [MIC] knob to the fully counter-clock-
wise position.
Press the PTT switch, then gently rotate the [MIC]
knob to the fully clockwise position.
Rotate the [SUB(VFO-B)] knob for 100 W (+5W/–
0W) on the Wattmeter, then rotate the [SUB(VFO-
B)] knob so that the VFO-B frequency indication
"10" increase.
Release the PTT switch.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d17 iAL"for the 50 MHz
amateur band´s ALC Adjustment, then rotate the
[SUB(VFO-B)] knob so that the VFO-B frequency
display shows "0020."
Rotate the [MIC] knob to the fully counter-clock-
wise position.
Press the PTT switch, then gently rotate the [MIC]
knob to the fully clockwise position.
Rotate the [SUB(VFO-B)] knob for 100 W (+5W/–
0W) on the Wattmeter, then rotate the [SUB(VFO-
B)] knob so that the VFO-B frequency indication
"10" increase.
Release the PTT switch.
Press and hold in the [MENU] button for 2 sec-
onds to save the new setting and exit from the
alignment mode.
Power Adjustment
Connect the 50-Ohm Dummy Load and Wattme-
ter to the "ANT 1" jack.
Rotate the [RF PWR] knob to fully clockwise.
Set the Main Band (VFO-A) frequency to 14.200
MHz in the CW mode.
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d22AP2h."
Rotate the [SUB(VFO-B)] knob so that the VFO-B
frequency display shows "0."
Press the PTT switch, then rotate the [SUB(VFO-
B)] knob for 100 W (+5 W/–0 W) on the Wattme-
ter, and confirm the the Sub S-meter is deflect.
Release the PTT switch.
Press and hold in the [MENU] button for 2 sec-
onds to save the new setting and exit from the
alignment mode.
ALC Meter Adjustment
Connect the 50-Ohm Dummy Load and Wattme-
ter to the "ANT 1" jack.
Connect the Audio Generator to
pin 8 of the MIC jack (pin 7:
GND), then set the output level
to +0 mV @1 kHz.
Set the Main Band (VFO-A) frequency to 14.200
MHz in the USB mode.
Rotate the [MIC] knob to the 12 o'clock position,
and rotate the [RF PWR] knob to the fully clock-
wise position.
Press and hold in the [1(1.8)], [2(3.5)], and [3(7)]
keys, while turning the radio on, to enter the
alignment mode.
Rotate the Main Tuning Dial knob to select the
alignment parameter "d50 ALC."
Press the PTT switch, then adjust the Audio Gen-
erator output level to the position where the ALC
meter just starts to deflect.
Release the PTT switch, then increase the Audio
Generator output level for "9 dB."
Press the [ENT] key, while pressing and holding
in the PTT switch, then rotate the [SUB(VFO-B)]
knob for maximum deflection on the ALC meter
zone (S9+10dB).
Alignment
MIC IN
MIC GND
ALIGNMENT-17