Page 1 When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your complete satisfaction. He will provide quality maintenance and any other assistance you may require. If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number: U.S. OWNERS: Toyota Customer Assistance Center Toll−free:1−800−331−4331...
Page 2 ’02 L/C U (L/O 0108) Important information about this manual Safety and vehicle damage warnings Safety symbol Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to aboid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows: CAUTION...
Page 3 Important information about your Toyota New vehicle warranty Accessories, spare parts and modification of your Toyota Your new vehicle is covered by the following Toyota limited warranties: A wide variety of non−genuine spare parts and accesso- D New vehicle warranty...
Page 4: Driving Tips
Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you dis- pose of your vehicle.
Page 5 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview ........Instrument cluster overview .
Page 6: Instrument Panel Overview
’02 L/C U (L/O 0108) Instrument panel overview "View A 1. Side vents 2. Side defroster outlets 3. Instrument cluster 4. Center vents 5. Electric moon roof switches and/or personal lights 6. Glove box 7. Power door lock switches 8. Power window switches 9.
Page 7 ’02 L/C U (L/O 0108) "View B 1. Headlight, turn signal and front fog light switches 2. Cruise control switch 3. Ignition switch 4. Wiper and washer switches 5. Emergency flasher switch 6. Power antenna switch 7. Car audio 8. Clock and outside temperature display 9.
Page 8 ’02 L/C U (L/O 0108) "Lower part of center cluster panel 1. Ashtray 2. Cigarette lighter 3. Power outlet...
Page 9 ’02 L/C U (L/O 0108) Instrument cluster overview 1. Voltmeter 4. Tachometer 7. Odometer and two trip meters 2. Speedometer 5. Engine oil pressure gauge 8. Trip meter reset knob 3. Service reminder indicators and 6. Engine coolant temperature gauge 9.
Page 10 ’02 L/C U (L/O 0108) Indicator symbols on the instrument panel ∗ 1 ∗ 1 Brake system warning light Unengaged ”Park” warning light Automatic transmission fluid temperature warning ∗ 1 Driver’s seat belt reminder light ∗ 1 light ∗ 1 Front passenger’s seat belt reminder light Turn signal indicator lights ∗...
Page 11 ’02 L/C U (L/O 0108) Automatic transmission indicator lights ∗ 1 Vehicle skid control system off indicator light Vehicle skid control system and active traction ∗ 1 control system warning light Active traction control system indicator light Slip indicator light ∗...
Page 12 ’02 L/C U (L/O 0108)
Page 13: Table Of Contents
’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys ............Engine immobiliser system .
Page 14: Keys
When using a key containing a trans- 1. Master key (black)—This key works in remote control key, see ”Side doors” in ponder chip, observe the following every lock. Your Toyota dealer will this section. precautions: need it to make you a new key with built−in transponder chip.
Page 15 ’02 L/C U (L/O 0108) z Do not cover the key grip with any material that cuts off electromagnet- ic waves. z Do not knock the key hard against other objects. z Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.
Page 16: Engine Immobiliser System
Toyota dealer. need additional keys, duplicates can be the electronic code in the chip corre- made by a Toyota dealer using the key The indicator light stays on except sponds to the registered ID code for number.
Page 17: Side Doors
This device complies with Part 15 of the FCC Rules. Operation is subject to the For your Toyota dealer to make you a following two conditions: new key with built−in transponder chip, your dealer will need your key number (1) This device may not cause harmful and master key.
Page 18 ’02 L/C U (L/O 0108) LOCKING UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch on the front side. To unlock: Push the switch on the rear side. All the side doors and back door lock or unlock simultaneously.
Page 19: Wireless Remote Control
’02 L/C U (L/O 0108) —Wireless remote control CAUTION Before driving, be sure that the doors closed locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident.
Page 20 ’02 L/C U (L/O 0108) Your vehicle has a wireless remote Together with the activation of unlocking, control system that can lock or unlock the interior light comes on for 15 seconds all the side doors and back door from a if the interior light switch is in “DOOR”...
Page 21 If you lose your wireless remote control objects or dropping it. no guarantee that interference will not key, contact your Toyota dealer as soon occur in a particular installation. If this Avoid putting it in water. as possible to avoid the possibility of equipment does cause harmful interfer- theft, or an accident.
Page 22 Changes modifications equivalent type recommended by a pressly approved by the party respon- Toyota dealer. sible for compliance could void the user’s authority to operate the equip- z Dispose of used battery according ment. to the local laws.
Page 23 ’02 L/C U (L/O 0108) 4. Install the lid with the 2 screws. 5. Install the module into the key frame and secure the cover with the screw. 6. When pushing any switch on the wire- less key, make sure the indicator light comes on.
Page 24: Power Windows
’02 L/C U (L/O 0108) Power windows Window lock switch 12C010 12C011 The windows can be operated with the Automatic operation: Push the switch OPERATING THE PASSENGERS’ WIN- switch on each side door. completely down or pull it completely up, DOWS and then release it.
Page 25 ’02 L/C U (L/O 0108) CAUTION To avoid serious personal injury, you must do the following. Always make sure the heads, hands and other parts of the bodies of all 12C007 occupants are kept completely in- side the vehicle before you close the power windows.
Page 26: Power Quarter Windows
’02 L/C U (L/O 0108) Power quarter windows Never try jamming any part of your CAUTION body in a window to make the jam protection function work intention- To avoid serious personal injury, you ally. must do the following. The jam protection function may Always make sure the hands and not work if something gets caught other parts of the body of all occu-...
Page 27: Back Door
’02 L/C U (L/O 0108) Back door LOCKING AND UNLOCKING WITH KEY Pull the handle and pull down the lower LOCKING AND UNLOCKING FROM IN- side of the back door. SIDE Insert the key into the key hole and turn it. When closing the back door, make sure To lock: Push the knob.
Page 28 ’02 L/C U (L/O 0108) CAUTION Keep the back door closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle. If the open back door hides the stop and tail lights, rear turn signal lights or rear retro reflectors while you are parked, other road users must be warned of the presence of...
Page 29: Hood
’02 L/C U (L/O 0108) Hood CAUTION Before driving, be sure that the back door is closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve-...
Page 30: Theft Deterrent System
’02 L/C U (L/O 0108) Theft deterrent system The system will automatically be set after 30 seconds. When the system is set, the indicator light will start flashing again. 4. After making sure the indicator light starts flashing, you may leave the ve- hicle.
Page 31: Fuel Tank Cap
If the system does not work properly, Turn the ignition key from the ”LOCK” have it checked by your Toyota dealer. to ”ON” position. Unlock any of the side doors or back door with the key or wireless remote control key.
Page 32 CAUTION Make sure the cap is tightened se- curely to prevent fuel spillage in case of an accident. Use only a genuine Toyota fuel tank 12C006 cap for replacement. It is designed to regulate fuel tank pressure. 1. To open the fuel filler door, pull the 2.
Page 33: Electric Moon Roof
’02 L/C U (L/O 0108) Electric moon roof To operate the moon roof, use the The roof will fully close. To stop the roof switches beside the personal light. partway, push the same switch or tilt switch. The moon roof works when the ignition switch is in the ”ON”...
Page 34 ’02 L/C U (L/O 0108) CAUTION Never sit on top of the vehicle around the roof opening. To avoid serious personal injury, you Never try jamming any part of your must do the following. body to make the jam protection While the vehicle is moving, always function work intentionally.
Page 35 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Seats, Seat belts, Steering wheel and Mirrors Seats ............Front seats .
Page 36: Seats
’02 L/C U (L/O 0108) Front seats— —Seat adjustment precautions Seats While the vehicle is being driven, all ve- Adjust the driver’s seat so that the foot While adjusting the seat, do not put hicle occupants should have the seatback pedals, steering wheel...
Page 37: Adjusting Front Seats
’02 L/C U (L/O 0108) —Adjusting front seats 1. SEAT POSITION AND SEAT CUSHION CAUTION ANGLE ADJUSTING SWITCH Move the control switch in the desired To reduce the risk of sliding under direction. the lap belt during a collision, avoid Releasing the switch will stop the seat at reclining the seatback any more than that position.
Page 38: Armrests
’02 L/C U (L/O 0108) Rear seats— —Rear seat precautions Armrest Folding the seats up will enlarge the lug- CAUTION gage compartment. See ”Luggage stowage precautions” in Section 2 for precautions Any operations should not be made in loading luggage. while the vehicle is moving.
Page 39 ’02 L/C U (L/O 0108) —Moving second seat —Adjusting second seats third seat entry SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION To reduce the risk of sliding under belt during collision,...
Page 40 ’02 L/C U (L/O 0108) —Folding up second seat CAUTION After returning the seat, make sure the seat is securely locked by push- ing forward and rearward on the top of the seatback and by trying to pull up the edge of the bottom cushion. BEFORE FOLDING UP SECOND SEAT 2.
Page 41 ’02 L/C U (L/O 0108) FOLDING UP SECOND SEAT 2. Unlock the seat cushion. Swing the 3. Hook the strap. whole seat up and forward. 1. Lower the outer head restraint to the When returning the second seat to its lowest position and pull up the cen- original position, put the holding strap into ter head restraint.
Page 42 ’02 L/C U (L/O 0108) CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 43 ’02 L/C U (L/O 0108) —Adjusting third seats —Folding up third seats SEATBACK ANGLE ADJUSTING LEVER Lean forward and pull the lever toward you. Then lean back to the desired angle and release the lever. CAUTION To reduce the risk of sliding under belt during collision,...
Page 44 ’02 L/C U (L/O 0108) 2. Make sure the shoulder belt passes FOLDING UP THIRD SEAT 2. Unlock the seat cushion and slide through the hanger when folding the the whole seat the rear−most 1. Lower the head restraint to the low- third seat.
Page 45 ’02 L/C U (L/O 0108) 3. Swing the whole seat up. 4. Hook the strap. 5. Remove the seat striker covers from the back of the seat cushion, and When returning the third seat to its origi- install them over the seat strikers. nal position, put the holding strap into the hole.
Page 46 ’02 L/C U (L/O 0108) —Removing third seats CAUTION When returning seats to their original position, observe the following pre- cautions in order to prevent personal injury in a collision or sudden stop: Make sure the seat is securely locked by pushing forward and rear- ward on the top of the seatback and by trying to pull up the edge of the bottom cushion.
Page 47: Head Restraints
’02 L/C U (L/O 0108) Head restraints CAUTION When reinstalling the seat, be care- ful not to hit the seat against you When removing or reinstalling the or inside of the vehicle. seat, observe the following precau- Install each seat in the same posi- tions to prevent personal injury: tion from which it was removed.
Page 48: Seat Heaters
’02 L/C U (L/O 0108) Seat heaters For your safety and comfort, adjust the Right side CAUTION head restraint before driving. front seat To raise: Pull it up. Occupants must use caution when op- To lower: Push it down while pressing the erating the seat heater because it lock release button.
Page 49: Seat Belts
’02 L/C U (L/O 0108) Seat belts— —Seat belt precautions Toyota strongly urges that the driver and Do not allow the child to stand up or NOTICE passengers in the vehicle be properly re- kneel on either rear or front seats. An...
Page 50 ’02 L/C U (L/O 0108) —3−point seat belts CAUTION Keep the belts clean and dry. If they need cleaning, use a mild soap Persons should ride in their seats solution or lukewarm water. Never properly wearing their seat belts use bleach, dye, or abrasive clean- whenever vehicle moving.
Page 51 After adjustment, make sure the anchor is buckle. locked in position. If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.
Page 52 ’02 L/C U (L/O 0108) CAUTION Take up slack Both high−positioned lap belts and loose−fitting belts could cause seri- ous injuries due to sliding under the Too high lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as pos- sible.
Page 53 If the seat belt does not function Keep as low on hips as possible normally, immediately contact your Toyota dealer. Do not use the seat Sit up straight and well back in the Remove excess length of the belt and until the seat belt is fixed.
Page 54: Seat Belt Extender
Please contact your local Toyota dealer to nally intended. order the proper required length for the extender. Bring the heaviest coat you ex- pect to wear for proper measurement and selection of length.
Page 55 If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat To connect the extender to the seat The driver and front passenger’s seat until the seat belt is fixed. It cannot...
Page 56 Failure to follow this instructions can 3. Seat belt pretensioner assemblies airbag sensor assembly, front airbag sen- result in death or serious injuries. Consult your Toyota dealer about any sors, front seat belt pretensioner assem- 4. Airbag sensor assembly repairs and modifications.
Page 57 Repairs on or near the front seat belt retractor assemblies This front seat belt pretensioner system In the following cases, contact your Toyota z Modification of the suspension sys- has a service reminder indicator to inform dealer as soon as possible: the driver of operating problems.
Page 58: Srs Driver And Front Passenger Airbags
’02 L/C U (L/O 0108) SRS driver and front passenger airbags CAUTION A driver or front passenger who is too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. To- yota strongly recommends that: The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve-...
Page 59 ’02 L/C U (L/O 0108) However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if it is involved in an underride collision (e.g.
Page 60 ’02 L/C U (L/O 0108) In a severe frontal impact, the sensors detect deceleration and the system trig- gers the airbag inflators. At this time, a chemical reaction in the inflators quickly Hitting a curb, Falling into or fills the airbags with non−toxic gas to help edge of pavement jumping over a restrain the forward motion of the occu-...
Page 61 The front seat occupants can child restraint system. Toyota be killed or seriously injured by the strongly recommends that all in- inflating airbags if they do not wear fants and children be placed in the the available seat belts properly.
Page 62 ’02 L/C U (L/O 0108) Move seat fully back Never put a rear−facing child re- A forward−facing child restraint sys- Do not sit on the edge of the seat straint system on the front passen- tem should be allowed to be put on or lean over the dashboard when ger seat because the force of the the front passenger seat only when...
Page 63 Failure to follow these instructions can result in death or serious injury. Consult your Toyota dealer about any repairs and modifications. Do not allow a child to stand up or Do not put objects or your pets on...
Page 64 Modification of the suspension sys- This SRS airbag system has a service In the following cases, contact your Toyota z Modification of the front end struc- reminder indicator to inform the driver of dealer as soon as possible:...
Page 65: Child Restraint
’02 L/C U (L/O 0108) Child restraint— —Child restraint precautions Toyota strongly urges the use of child Toyota strongly urges use of Make sure you have complied with restraint systems children small proper child restraint system which all installation instructions provided enough to use them.
Page 66: Child Restraint System
’02 L/C U (L/O 0108) —Child restraint system A child restraint system for a small When not using the child restraint system, CAUTION child or baby must itself be properly keep it secured with the seat belt or place restrained on the seat with either the it somewhere other than the passenger Never put a rear−facing child re- lap belt or the lap portion of the lap/...
Page 67 ’02 L/C U (L/O 0108) —Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.
Page 68 ’02 L/C U (L/O 0108) —Installation with 2−point type seat belt (A) INFANT SEAT INSTALLATION 1. Run the center lap belt through or CAUTION around the infant seat following the An infant seat is used in rear−facing instructions provided by its manufactur- position only.
Page 69 Contact your 2. While pressing the infant seat firmly Toyota dealer immediately. Do not CAUTION against the seat cushion and seatback, use the child restraint seat until the tighten the lap belt by pulling its free seat belt is fixed.
Page 70 ’02 L/C U (L/O 0108) 3. To remove the infant seat, press the (B) CONVERTIBLE SEAT INSTALLATION CAUTION buckle−release button. A convertible seat is used in forward− facing or rear−facing position depend- Do not put a rear−facing child re- ing on the child’s age and size. When straint system on the third seat if it installing, follow...
Page 71 Contact your 1. Run the center lap belt through or 2. While pressing convertible seat Toyota dealer immediately. Do not around the convertible seat following firmly against the seat cushion and use the child restraint seat until the instructions provided seatback, tighten the lap belt by pulling seat belt is fixed.
Page 72 ’02 L/C U (L/O 0108) —Installation with 3−point type seat belt 3. To remove the convertible seat, press (A) INFANT SEAT INSTALLATION CAUTION the buckle−release button. An infant seat is used in rear−facing position only. Push and pull the child restraint sys- tem in different directions to be sure it is secure.
Page 73 ’02 L/C U (L/O 0108) 1. Run the lap and shoulder belt through CAUTION Do not put a rear−facing child re- or around the infant seat following the straint system on the second (or instructions provided by its manufactur- Never put a rear−facing child re- third) seat if it interferes with the er and insert the tab into the buckle straint system on the front passen-...
Page 74 2. Fully extend the shoulder belt to put it 3. While pressing the infant seat firmly Toyota dealer immediately. Do not in the lock mode. When the belt is against the seat cushion and seatback, use the child restraint seat until the...
Page 75 ’02 L/C U (L/O 0108) 4. To remove the infant seat, press the (B) CONVERTIBLE SEAT INSTALLATION CAUTION buckle−release button and allow the A convertible seat is used in forward− belt to retract completely. The belt will facing or rear−facing position depend- Push and pull the child restraint sys- move freely again and be ready to ing on the child’s age and size.
Page 76 ’02 L/C U (L/O 0108) Move seat fully back CAUTION A forward−facing child restraint sys- Do not put a rear−facing child re- tem should be allowed to be put on straint system on the second (or Never put a rear−facing child re- the front passenger seat only when third) seat if it interferes with the straint system on the front passen-...
Page 77 1. Run the lap and shoulder belt through 2. Fully extend the shoulder belt to put it Toyota dealer immediately. Do not or around the convertible seat following in the lock mode. When the belt is use the child restraint seat until the...
Page 78 ’02 L/C U (L/O 0108) 3. While pressing convertible seat 4. To remove the convertible seat, press CAUTION firmly against the seat cushion and the buckle−release button and allow the seatback, let the shoulder belt retract belt to retract completely. The belt will Push and pull the child restraint sys- as far as it will go to hold the convert- move freely again and be ready to...
Page 79 ’02 L/C U (L/O 0108) Move seat fully back (C) BOOSTER SEAT INSTALLATION 1. Sit the child on a booster seat. Run CAUTION the lap and shoulder belt through or A booster seat is used in forward−fac- around the booster seat and child fol- ing position only.
Page 80 Contact your is positioned across the center of Toyota dealer immediately. Do not child’s shoulder. The belt should be use the child restraint seat until the kept away from child’s neck, but seat belt is fixed. not falling off child’s shoulder. Fail-...
Page 81 ’02 L/C U (L/O 0108) —Using a top strap Symbol 13C003 13C001 13C002 Anchor brakets Follow the procedure below for a child Use the anchor bracket located behind the TO USE THE ANCHOR BRACKET: restraint system that requires the use second seat on the floor to attach the top 1.
Page 82 ’02 L/C U (L/O 0108) —Installation with child restraint lower anchorages 13C005 13C006 13C004 2. Fix the child restraint system with 4. Replace the head restraint. The lower anchorages for the child re- the seat belt. straint system interfaced with 3.
Page 83 ’02 L/C U (L/O 0108) Type A— 2. Latch the hooks of lower straps onto the anchorages and tighten the lower 13C007 straps. Type B— 2. Latch the buckles onto the anchor- 13C009 ages If your child restraint system has a top strap, it should be anchored.
Page 84: Manual Tilt Steering Wheel
’02 L/C U (L/O 0108) Manual tilt steering wheel CAUTION CAUTION When using the lower anchorages Do not adjust the steering wheel for the child restraint system, be while the vehicle is moving. Doing sure that there are no irregular ob- so may cause the driver to mishan- jects around the anchorages or that dle the vehicle and an accident may...
Page 85: Power Tilt And Telescopic Steering Wheel
This feature can be set inoperative. Ask ries. your Toyota dealer.
Page 86: Outside Rear View Mirrors
’02 L/C U (L/O 0108) —Power rear view mirror control Outside rear view mirrors— CAUTION Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.
Page 87: Anti−Glare Inside Rear View Mirror
’02 L/C U (L/O 0108) Anti−glare inside rear view mirror— —Folding rear view mirrors NOTICE If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror. 13C010 The rear view mirrors can be folded Adjust the mirror so that you can just...
Page 88 ’02 L/C U (L/O 0108) —Compass When the ignition key is inserted and Pushing the “AUTO” button for longer turned on, the inside rear view mirror al- 3 seconds turns on or off the compass ways turns on in the “AUTO” mode. display.
Page 89 ’02 L/C U (L/O 0108) NOTICE Do not put magnets or a metal object near the inside rear view mirror. Do- ing this may cause malfunction of the compass sensor. CALIBRATING THE COMPASS (deviation calibration) The direction display on the compass deviates from the true direction deter- mined by the earth’s magnetic field, The amount of deviation varies according to...
Page 90 After driving in 1 to 3 circles in the above dure below. method, calibration is complete with the direction shown on the display. If calibration cannot be performed because of the magnetized vehicle, etc., take your vehicle to Toyota dealer.
Page 91: Sun Visors
’02 L/C U (L/O 0108) Sun visors— Do not perform circling calibration of the compass in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).
Page 92: Vanity Mirror
’02 L/C U (L/O 0108) —Vanity mirror To use the vanity mirror, swing down the main sun visor and open the cover. The vanity light comes on when you open the cover.
Page 93 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlight and turn signals ........Emergency flashers .
Page 94: Headlight And Turn Signals
’02 L/C U (L/O 0108) Headlight and turn signals The headlights automatically turn off after some time since the ignition switch is turned off, then any side door is opened. To turn them on again, turn the key to the ”ON”...
Page 95: Emergency Flashers
’02 L/C U (L/O 0108) Emergency flashers High−Low beams—For high beams, turn TURN SIGNALS To turn on the emergency flashers, push the switch. the headlights on and push the lever away To signal a turn, push the headlight/ from you (position 1). Pull the lever to- All the turn signal lights will flash.
Page 96: Instrument Panel Light Control
’02 L/C U (L/O 0108) Instrument panel light control Front fog lights NOTICE To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running. To adjust the brightness of the instru- To turn on the front fog lights, twist ment panel lights, turn the dial.
Page 97: Interior Lights
’02 L/C U (L/O 0108) Interior lights ILLUMINATED ENTRY SYSTEM INTERIOR LIGHTS CUT OFF OPERATION Center— When the ignition switch is ”OFF” and any With the switch in the ”DOOR” position, interior lights in the vehicle stay lighting the light comes on when either side or on, the lights will cut off automatically back door is opened.
Page 98: Personal Lights
’02 L/C U (L/O 0108) Center interior and personal lights Personal lights All the lights are cut off when all the doors are locked by key or wireless re- mote control key. To turn on the personal light, push the CENTER INTERIOR LIGHT switch on 1 side.
Page 99: Ignition Switch Light
’02 L/C U (L/O 0108) Ignition switch light CENTER PERSONAL LIGHTS INTERIOR AND PERSONAL LIGHTS CUT OFF OPERATION To turn on the center personal light, push the switch on 1 side. To turn the When the ignition switch is ”OFF” and any lights off, push the switch on 2 side.
Page 100: Windshield Wipers And Washer
’02 L/C U (L/O 0108) Windshield wipers and washer Rear window wiper and washer To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see ”Adding washer fluid”...
Page 101: Rear Window Defogger
’02 L/C U (L/O 0108) Rear window defogger Make sure you turn the defogger off when NOTICE the surfaces are clear. Leaving the defog- ger on for a long time could cause the Do not operate the rear wiper if the battery discharge, especially...
Page 102: Outside Rear View Mirror Heaters
’02 L/C U (L/O 0108) Outside rear view mirror heaters CAUTION Since the mirror surfaces can get hot, do not touch them when the mirror heater switch is on. Make sure you turn the mirror heaters off when the surfaces are clear. Leaving the mirror heaters on for a long time could cause the battery to discharge, especially during stop−and−go driving.
Page 103 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge ..........Engine coolant temperature gauge .
Page 104: Fuel Gauge
Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. 15C004 The gauge works when the ignition...
Page 105: Engine Oil Pressure Gauge
If the engine oil pressure should stay be- low the normal range, pull off the road to a safe place and stop the engine immedi- ately. Call a Toyota dealer or qualified repair shop for assistance. Engine oil pressure may not build up when the engine oil level is too low.
Page 106: Voltmeter
’02 L/C U (L/O 0108) Voltmeter Tachometer Odometer and two trip meters The voltmeter tells whether the battery The tachometer indicates engine speed This meter displays the odometer and is charged discharged. Check in thousands of rpm (revolutions per two trip meters. while the engine is running—the needle minute).
Page 107: Service Reminder Indicators And Warning Buzzers
A to trip meter Take vehicle to B, then back to the odometer each If parking brake is Toyota d ealer time you push. off, stop immediate- immediately. To reset the trip meter A to zero, dis-...
Page 108 The light may stay on for about 60 leased. a safe place and contact your Toyota seconds after the ignition key is turned When the brake fluid level is low... dealer.
Page 109: Driver's Seat Belt Reminder Light
The engine ignition will continue to oper- If the lamp will not go off even after sev- ate, however, until the battery is dis- eral trips, contact your Toyota dealer as Once the ignition key is turned to ”ON” or charged. Turn off the air conditioning, soon as possible.
Page 110: Low Fuel Level Warning Light
Contact your This light comes on when the fuel level Toyota dealer as soon as possible to in the tank becomes nearly empty. Fill up service the vehicle. the tank as soon as possible. The light does not come on when the ignition key is turned to the “ON”...
Page 111: Open Door Warning Light
CAUTION This light warns that the transmission If the light does not go off, call a Toyota ”Park” mechanism is not engaged. If the dealer or qualified repair shop for assis- If the “ABS” warning light remains on four−wheel drive control is in the ”N”...
Page 112 TORS (except the low fuel level warning ing buzzer does not function as described light) above, have it checked by your Toyota 1. Apply the parking brake. dealer as soon as possible. 2. Open one of the side doors or back door.
Page 113 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock ......Automatic transmission .
Page 114: Ignition Switch With Steering Lock
’02 L/C U (L/O 0108) Ignition switch with steering lock ”LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position. To turn the key from ”ACC” to the ”LOCK” position, you must put the selector lever in the ”P”...
Page 115: Automatic Transmission
’02 L/C U (L/O 0108) Automatic transmission Lock release button To prevent misshifting Overdrive switch For selecting either a three−speed or Parking, engine starting and four−speed transmission key removal position Reverse position “O/D OFF” indicator Neutral position light on the instrument panel Normal driving position shows the overdrive...
Page 116 ’02 L/C U (L/O 0108) Your automatic transmission has a shift When the cruise control is being used, lock system to minimize the possibility of even if you downshift the transmission by incorrect operation. This means you can pushing releasing overdrive only shift out of ”P”...
Page 117 ’02 L/C U (L/O 0108) Shift into the ”L” position. The trans- With the selector lever in ”2” or ”L”, you CAUTION mission will downshift to first gear can start the vehicle in motion as with the when the vehicle speed drops down to lever in ”D”.
Page 118 ’02 L/C U (L/O 0108) (e) Backing up NOTICE CAUTION 1. Bring the vehicle to a complete stop. Do not hold the vehicle on an up- 2. With the brake pedal held down with While the vehicle is moving, never grade with the accelerator pedal.
Page 119: Four-Wheel Drive System
’02 L/C U (L/O 0108) Four–wheel drive system— (a) Four–wheel drive contro l For ordinary driving, Toyota recommends NOTICE using the Normal mode to improve fuel economy. If you rock your vehicle, observe the following precautions to prevent dam- (j) If you cannot shift the selector le- age to the transmission and other ver out of ”P”...
Page 120 ’02 L/C U (L/O 0108) Use the center differential lock system if “H” (high speed position, center differ- “L” (low speed position, center differen- your wheels get stuck in a ditch, or when ential locked): Lever at “H”, center differ- tial locked): Lever at “L”, center differen- you are driving on a slippery or bumpy ential lock button pushed in...
Page 121 ’02 L/C U (L/O 0108) (b) Shifting procedure Advice for driving on slippery roads in The four−wheel drive control lever in SHIFTING BETWEEN “H” (UNLOCKED) AND “H” (LOCKED) “L” (low speed position) mode “L” position and the automatic transmission lever in the “R” position If you shift the four−wheel drive control shift between...
Page 122: Parking Brake
’02 L/C U (L/O 0108) Parking brake Cruise control The cruise control allows you to cruise CAUTION the vehicle at a desired speed over about 40 km/h (25 mph) even with your Before driving, be sure the parking foot off the accelerator pedal. brake is fully released and the park- Your cruising speed can be maintained ing brake reminder light is off.
Page 123 ’02 L/C U (L/O 0108) CAUTION To help maintain maximum control of your vehicle, do not use the cruise control when driving heavy or varying traffic, or on slip- – pery (rainy, icy or snow covered) or winding roads. Avoid vehicle speed increases when driving downhill.
Page 124 If this is the case, contact your Toyota not cancelled. To decrease the vehicle dealer and have your vehicle inspected. speed, reset to a slower speed with the cruise control lever or depress the brake pedal.
Page 125: Active Traction Control System
If the “VSC/TRAC” warning light comes controlling the output of the brake and on, have your vehicle checked by your engine. Thus, the system assists driver Toyota dealer as soon as possible. control driving power wheels. When you turn the ignition...
Page 126 (The continuous buzzer sounds for about In the following cases, contact your Toyota snow tires or tire chains. Always 3 seconds.) At the time, the “VSC/TRAC”...
Page 127: Vehicle Skid Control System
4 tires should be the same. If you use the tires other than specified, or different type or size, the vehicle skid control sys- function correctly. When replacing the tires or wheels, contact your Toyota dealer. (See “Checking and replacing tires” in Section 7−2.)
Page 128 “Four−wheel drive system—(a)Four−wheel If the “VSC/TRAC” warning light and “VSC In the following cases, contact your Toyota drive control” in this section.) OFF” indicator light come on, have your dealer: vehicle checked by your Toyota dealer as The “VSC/TRAC”...
Page 129 If you use the tires other than specified, or different type or size, the vehicle skid control sys- tem may not function correctly. When replacing the tires or wheels, contact your Toyota dealer. (See “Checking and replacing tires” in Section 7−2.)
Page 130 ’02 L/C U (L/O 0108)
Page 131 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference ..........Using your audio system .
Page 132 —some basics Reference This section describes some of the basic TONE AND BALANCE features on Toyota audio systems. Some For details about your system’s tone and information may not pertain to your sys- balance controls, see the description of tem.
Page 133 The antenna automatically extends when make sure it is retracted before the radio is on or the radio system is on, driving your Toyota through an au- and retracts when the radio mode is off. tomatic car wash. To lower a power antenna, push the ” ”...
Page 134 ’02 L/C U (L/O 0108) YOUR CASSETTE PLAYER NOTICE When you insert a cassette, the exposed Never try to disassemble or oil any tape should be to the right. part of the compact disc player. Do NOTICE not insert anything except a compact disc into the slot.
Page 135 ’02 L/C U (L/O 0108) —Controls and features Details of specific buttons, controls, and features are described in the alphabetical listing that follows.
Page 136 ’02 L/C U (L/O 0108) 1 2 3 4 5 6 (Preset buttons) Compact disc (Program) These buttons are used to preset and To eject one compact disc only: Push and Push “ ” to select the other side of a tune in radio stations.
Page 137 ’02 L/C U (L/O 0108) If a tape side rewinds completely, the cas- CONTROL / MODE (Audio control and For front/rear adjustment, push “CONTROL sette player will stop and then play that mode adjustment) / MODE” repeatedly until “FAd” appears same side.
Page 138 FM stations, two for If the malfunction is not rectified, take will close after 15 seconds. each button. your vehicle to your Toyota dealer. Loading multiple compact discs— If the audio system is off, you can turn DISC on the radio by pushing “FM1·2”.
Page 139 ’02 L/C U (L/O 0108) PWR·VOL (Power and Volume) RPT (Repeat) Repeating a disc: Push and hold “ ” until you hear a Push “PWR·VOL” to turn the audio system Cassette Player on and off. Turn “PWR·VOL” to adjust the beep.
Page 140 ’02 L/C U (L/O 0108) To scan all the frequencies: Scanning the first track of all the discs in Next, push either side of the track button Quickly push and release “SCAN”. If you the player: until the number on the display reaches hear a beep, you held the button too long, Push “SCAN”...
Page 141 Your Toyota has an electronic tuning radio If the signal becomes extremely weak, the dio system which you are listening (ETR).
Page 142 ’02 L/C U (L/O 0108) Here are some common reception prob- Use high−quality cassettes. lems that probably do not indicate a prob- Fading—AM broadcasts are reflected by Low−quality cassette tapes can cause lem with your radio: the upper atmosphere—especially at night. many problems, including poor sound, These reflected signals can interfere with inconsistent...
Page 143 ’02 L/C U (L/O 0108) If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears to be working. Remove the disc from the player and wait until it dries. CARING FOR YOUR COMPACT DISC PLAYER AND DISCS Use only compact discs labeled as...
Page 144 ’02 L/C U (L/O 0108) Your automatic changer or compact CAUTION disc player cannot play special shaped, labeled or low−quality compact discs Compact disc players use an invisible such as those shown here. Do not use laser beam which could cause hazard- them as the player could be damaged.
Page 145 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Front air conditioning system: Controls ..........Air flow selector settings .
Page 146: Front Air Conditioning System: Controls
’02 L/C U (L/O 0108) Front air conditioning system— —Controls 1. Air intake selector 2. Air flow selector 3. ”A/C” button 4. Fan speed selector 5. ”AUTO” position (for fan speed) 6. ”AUTO” position (for air flow) 7. Temperature selector...
Page 147 ’02 L/C U (L/O 0108) ”AUTO” position 4. Floor/Windshield—Air flows mainly from the floor vents and windshield For automatic operation of the air condi- vents. tioning, turn the fan speed and air flow selector knobs to the ”AUTO” position. It is recommended that you close the lower vent.
Page 148 If this happens, take your ve- hicle to a Toyota dealer for service. Air intake selector Press the button to select the air source. An indicator light will illuminate to show which air intake mode is being selected.
Page 149: Air Flow Selector Settings
’02 L/C U (L/O 0108) —Air flow selector settings 17C001 “Instrument panel vents” described below.
Page 150: Operating Tips
’02 L/C U (L/O 0108) —Operating tips To cool off your Toyota after it has If following another vehicle on a dusty Heating been parked in the hot sun, drive with road, or driving in windy and dusty For best results, set controls to: the windows open for a few minutes.
Page 151 ’02 L/C U (L/O 0108) Air conditioning Ventilation Defogging For best results, set controls to: For best results, set controls to: The inside of the windshield For best results, set controls to: Fan speed—”AUTO” Fan speed—”AUTO” Temperature—To the desired Temperature—To the desired Temperature—Towards high temperature temperature...
Page 152: Instrument Panel Vents
’02 L/C U (L/O 0108) —Instrument panel vents Defrosting The outside of the windshield For best results, set controls to: Temperature—Towards high temperature Air intake—FRESH (outside air) Air flow—WINDSHIELD Lower vent—CLOSED When turning the air flow control knob to windshield position, the air intake selects ”Fresh”...
Page 153: Rear Heater System
’02 L/C U (L/O 0108) Rear heater system 1. Fan speed selector This button is used to turn the rear heater system on and off, and adjust the fan speed. Pressing the button once adjusts the fan speed to the ”LO” mode and twice successionally adjusts the fan speed to the ”HI”...
Page 154: Rear Air Conditioning System
’02 L/C U (L/O 0108) Rear air conditioning system— —Controls 1. Rear air conditioning on−off button 2. ”AUTO” button 3. Air flow selector 4. Fan speed selector 5. Temperature selector 6. ”OFF” button...
Page 155 ’02 L/C U (L/O 0108) Rear air conditioning on−off button Temperature selector To turn the rear air conditioning on, press Move the lever to adjust the tempera- the ”REAR” button. To turn the rear air ture—to the right to warm, to the left to conditioning off, press the button again.
Page 156: Air Flow Selector Settings
’02 L/C U (L/O 0108) —Air flow selector settings Air at lower than room temperature does not flow from the floor vents. Warm air Cool air...
Page 157 ’02 L/C U (L/O 0108) SECTION − OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Clock ............Outside temperature display .
Page 158: Clock
’02 L/C U (L/O 0108) Clock Outside temperature display For example, if the ”:00” button is de- pressed when time between 1:01—1:29, the time will change to 1:00. If the time is between 1:30—1:59, the time will change to 2:00. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one...
Page 159: Cigarette Lighter And Ashtray
”ACC” position to use the light- plug that fits the outlet, or pouring juice or other liquid into the outlet Do not hold the cigarette lighter pressed may cause troubles or short cir- cuits. Use a Toyota genuine cigarette lighter or equivalent for replacement.
Page 160: Fuel Pump Shut−Off System
’02 L/C U (L/O 0108) Fuel pump shut−off system Instrument panel Rear console box (Vehicles with naviga- In response to a severe impact which tion system) may cause a large amount of vehicle deformation, the fuel pump shut−off system stops supplying fuel to the en- gine to minimize the risk of fuel leak- age.
Page 161: Rear Console Box
’02 L/C U (L/O 0108) Rear console box If the fuel pump shut−off system has acti- The fuel pump shut−off system is de- vated, you can turn on the fuel pump signed to activate in a collision which may shut−off system with the reset switch on cause a large amount of vehicle deforma- the impact detection sensor.
Page 162: Glove Box
’02 L/C U (L/O 0108) Glove box Garage door opener The battery side of the hand−held trans- mitter must be pointed away from the Indicator light HomeLink during the programming pro- cess. For Canadian users, follow the procedure in “Programming an entrance gate/Pro- gramming all devices in the Canadian market”.
Page 163 ’02 L/C U (L/O 0108) 5. Test the operation of the HomeLink 1. Locate the “training” button on the ceil- Programming an entrance gate/Program- pressing the newly programmed button. ing mounted garage door opener motor. ming all devices in the Canadian market If programming a garage door opener, The exact location and color of the 1.
Page 164 CANADA: 1763 102 264 security systems, home door locks or When programming the HomeLink This device complies with FCC Rules lighting, contact your authorized Toyota Universal Transceiver, you may be part 15. Operation is subject to the fol- dealer for assistance.
Page 165: Garage Door Opener Box
’02 L/C U (L/O 0108) Garage door opener box Your vehicle is equipped with a box To use the garage door opener box, do 2. Unscrew the screws on both sides designed to store a garage door opener the following. and remove the stay.
Page 166 ’02 L/C U (L/O 0108) 3. Remove Velcro loop on the stay. Re- Please note if the transmitter has wire clip 4. Install the transmitter on the center move the paper strip covering the for sun visor, this clip must be removed of the stay with Velcro.
Page 167 ’02 L/C U (L/O 0108) 5. Remove the cover on the opening on 6. Reinstall the stay and secure it with 7. Close the lid securely. the lid. the screws. Before fixing it with the Make sure the lid is closed securely. screws, adjust the position of the transmitter as it can be operated CAUTION...
Page 168: Auxiliary Boxes
’02 L/C U (L/O 0108) Auxiliary boxes— To use the auxiliary boxes, open the lids as shown in the following illustra- tions. CAUTION To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.
Page 169 ’02 L/C U (L/O 0108) —First−aid kit holder Types A and B auxiliary boxes are equipped with a band or strap to hold the first−aid kit. Although the first−aid kit itself is not in- cluded as an original equipment, this aux- iliary box can be used to store the first−...
Page 170: Cup Holders
’02 L/C U (L/O 0108) —Warning reflector holder Cup holders Types C and D auxiliary boxes are The cup holder is designed for holding equipped with a band or straps to hold cups or drink−cans securely. To use the warning reflector. them, observe the following illustra- tions.
Page 171 ’02 L/C U (L/O 0108) 19C008 For front seats For front seat For second seats The cup holder can be adjustable to the To use a cup holder in the console box. size of cups by changing the separator 1. Open the console box lid. Pull down position or moving the separator arms.
Page 172: Tie−Down Hooks
’02 L/C U (L/O 0108) Tie−down hooks Luggage cover For third seats (right−hand side −type b) Type A To secure your luggage, use the tie− down hooks as shown above. ”Luggage stowage precautions” Section 2 for precautions in loading lug- gage.
Page 173: Floor Mat
’02 L/C U (L/O 0108) Floor mat To use the luggage cover, pull it out of the retractor and hook it on the an- chors. To remove the luggage cover, lift it up. Use a floor mat of the correct size. After you remove the luggage cover, place If the floor carpet and floor mat have a it somewhere other than the passenger...
Page 174 ’02 L/C U (L/O 0108) CAUTION Make sure the floor mat is properly placed on the floor carpet. If the floor slips and interferes with movement of the pedals during driv- ing, it may cause an accident.
Page 175 ........Your Toyota’s identification .
Page 176: Off−Road Vehicle Precautions
’02 L/C U (L/O 0108) Off−road vehicle precautions This vehicle belongs to the utility ve- CAUTION hicle class, which has higher ground clearance and narrower tread in relation Always observe the following precau- to the height of its center of gravity to tions to minimize the risk of serious make it capable of performing in a wide personal injury or damage to your ve-...
Page 177: Break−In Period
To help prevent gas station mix−ups, your strike objects, etc. This may cause to the future economy and long life of Toyota has a smaller fuel tank opening. loss of control or vehicle rollover your vehicle: The special nozzle on pumps with un-...
Page 178 10% ethanol or 15% Automotive manufacturers in the U.S., heavy knocking. If it is severe, this will MTBE. If you use gasohol in your Toyota, Europe and Japan have developed a lead to engine damage. be sure that it has an octane rating no low-...
Page 179: Operation In Foreign Countries
’02 L/C U (L/O 0108) Operation in foreign countries Three−way catalytic converter GASOLINE QUALITY If you plan to drive your Toyota in another country... In a very few cases, you may experience driveability problems caused by the partic- First, comply with the vehicle registration ular gasoline that you are using.
Page 180 Use only unleaded gasoline. vehicle in for a check−up as soon as possible. Remember, your Toyota z Do not drive with an extremely low dealer knows your vehicle and its fuel level; running out of fuel could three−way catalytic converter sys-...
Page 181: Engine Exhaust Cautions
’02 L/C U (L/O 0108) Facts about engine oil consumption Engine exhaust cautions FUNCTIONS OF ENGINE OIL CAUTION Keep the back door and quarter Engine oil has the primary functions of windows closed while driving. An lubricating and cooling the inside of the Avoid inhaling the engine exhaust.
Page 182 When judging the amount of oil con- is essential that the oil level be checked sumption, note that the oil may become regularly. Toyota recommends that the oil diluted and make it difficult to judge level be checked every time you refuel the true level accurately.
Page 183: Iridium−Tipped Spark Plugs
If the brake system warning light comes on, immediately stop work. But you will have to push the pedal hard, much harder than nor- your vehicle and contact your Toyota deal- mal. And your braking distance will be longer.
Page 184 ’02 L/C U (L/O 0108) ANTI−LOCK BRAKE SYSTEM Depressing the brake pedal on slippery CAUTION (with “ABS” warning light) road surfaces such as on the manhole cover, the steel plate under the construc- The anti−lock brake system is designed overestimate anti−lock tion, joints in the bridge, etc.
Page 185 Contact your the anti−lock brake system and the surface is pitted or has other differ- Toyota dealer as soon as possible to brake assist system work properly, the ences in surface height. service the vehicle. light turns off after a few seconds.
Page 186: Buzzers" In Section
Section 1−5. hicle at a safe place and contact your brake shoes and/or drums are replaced. Toyota dealer. Have your Toyota dealer perform the bed- In this case, not only the anti−lock ding−down. brake system will fail but also the...
Page 187: Brake Pad Wear Limit Indicators
Toyota Do not place anything on the flat- ing, and impair the driver’s control dealer as soon as possible. Expensive ro- tened seat or it may slide forward of the vehicle.
Page 188: Rear Step Bumper
Use only a spare tire of the same CAUTION size, construction and load capacity as the original tires on your Toyota Do not allow more than one person because damage to the limited−slip to get on the rear step bumper at differential could possibly occur with a time.
Page 189: Your Toyota's Identification
This number is on the left top of the instrument panel, and can be seen through the windshield from outside. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.
Page 190: Theft Prevention Labels
’02 L/C U (L/O 0108) Theft prevention labels Suspension and chassis Types of tires Your new vehicle carries theft preven- Determine what kind of tires your ve- CAUTION tion labels which are approximately 56 hicle is originally equipped with. mm (2.20 in.) by 16 mm (0.63 in.). 1.
Page 191 ’02 L/C U (L/O 0108) CAUTION Do not mix summer and all season tires on your vehicle as this can cause dangerous handling charac- teristics, resulting in loss of con- trol. Do not use tire other than the manufacturer’s designated tires, and never mix tires or wheels of the sizes different from the originally equipped tires and wheels.
Page 192 ’02 L/C U (L/O 0108)
Page 193: Keys
’02 L/C U (L/O 0108) SECTION STARTING AND DRIVING Before starting the engine ........How to start the engine .
Page 194 ’02 L/C U (L/O 0108) How to start the engine– (a) Before cranking Before starting the engine (b) Starting the engine 1. Check the area around the vehicle be- 1. Apply the parking brake firmly. Before starting the engine, be sure to fol- fore entering it.
Page 195: Tips For Driving In Various Conditions
To dry them, drive vehicle cautiously while lightly pressing the brake pedal with the park- ing brake applied. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.
Page 196 ’02 L/C U (L/O 0108) Off−road driving precautions When driving your vehicle off−road, please U.S. Forest Service and Bureau of Do not drive in excess of the speed observe the following precautions to en- Land Management limit. Even if the legal speed limit sure your driving enjoyment and to help permits it, do not drive over 140 prevent the closure of areas to off−road...
Page 197 ’02 L/C U (L/O 0108) NOTICE z Always perform a maintenance in- After driving through tall grass, spection after each day of off−road mud, rock, sand, rivers, etc., check z If driving through water, such as driving that has taken you through that there is no grass, bush, paper, when crossing...
Page 198: Winter Driving Tips
”TOYOTA Long Life Coolant” or equivalent. harder starting. If you are not sure about accumulated in and around the parking which oil to use, call your Toyota dealer– brake mechanism may freeze, making it See Section 7−2 for details about coolant he will be pleased to help.
Page 199: Dinghy Towing
Ask your capacity. The combination of the local Toyota dealer for further details be- gross trailer weight added to the fore towing. total weight of the vehicle, occu-...
Page 200 ’02 L/C U (L/O 0108) Trailer hitch assemblies have differ- Total trailer weight Tongue load ent weight capacities established by the hitch manufacturer. Even though the vehicle may be physically capa- ble of towing a higher weight, the operator must determine the maxi- mum weight rating of the particular hitch assembly and never exceed the maximum weight rating speci-...
Page 201 Energy Absorbing Bumper, if so HITCHES equipped. If you wish to install a trailer hitch, you should consult with your Toyota dealer. Use only a hitch recommended by the hitch manufacturer and the one which conforms to the total trailer weight 1 Trailer ball load rating requirement.
Page 202 The trailer BRAKES AND SAFETY CHAINS ball load rating should be printed on Toyota recommends trailers with the top of the ball. brakes that conform to any applica- 3. When mounted in the ball mount, the...
Page 203 Check that your rear view mirrors con- BREAK−IN SCHEDULE form to any applicable federal, state/ provincial or local regulations. If not, Toyota recommends that you do not install the rear view mirrors required tow a trailer with a new vehicle or a for towing purpose.
Page 204 ’02 L/C U (L/O 0108) TRAILER TOWING TIPS Avoid jerky starts or sudden accelera- Crosswinds and rough roads will ad- tion. versely affect handling of your vehicle When towing a trailer, your vehicle will and trailer, causing sway. Pay attention handle differently than when not tow- Avoid jerky steering and sharp turns.
Page 205 ’02 L/C U (L/O 0108) Because of the added load of the trail- When restarting out after parking on a CAUTION er, your vehicle’s engine may overheat slope: on hot days temperatures over 1. With the transmission in ”P” posi- Do not exceed 72 km/h (45 mph) or 30°C [85°F]) when going up a long or tion, start the engine.
Page 206 ’02 L/C U (L/O 0108) How to save fuel and make your vehicle last longer, too Improving fuel economy is easy–just take Avoid engine over-revving. Use a Keep front wheels in proper it easy. It will help make your vehicle last gear position suitable for the road on alignment.
Page 207 ’02 L/C U (L/O 0108) CAUTION Never turn off the engine to coast down hills. Your power steering and brake booster will not function with- out the engine running. Also, the emission control system operates properly only when the engine is run- ning.
Page 208 ’02 L/C U (L/O 0108)
Page 209 ’02 L/C U (L/O 0108) SECTION IN CASE OF AN EMERGENCY If your vehicle will not start ........If your engine stalls while driving .
Page 210 ”How to start the Call a Toyota dealer or qualified repair 1. The engine may be flooded because of engine” in Section 3 and that you have shop.
Page 211 If the engine still will not start, it needs Batteries contain sulfuric acid adjustment or repair. Call a Toyota dealer which is poisonous and corrosive. NOTICE or qualified repair shop for assistance. Wear protective safety glasses when jump starting, and avoid spilling...
Page 212 ’02 L/C U (L/O 0108) JUMP STARTING PROCEDURE 1. If the booster battery is installed in Discharged battery Jumper cable another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories. Booster 2. If required, remove all the vent plugs battery from the booster and discharged batter- ies.
Page 213 ’02 L/C U (L/O 0108) If your engine stalls while driving 5. Start your engine in the normal way. If your engine stalls while driving... After starting, run it at about 2000 rpm 1. Reduce your speed gradually, keeping for several minutes with the accelerator a straight line.
Page 214 CAUTION your vehicle checked by your Toyota deal- flashers. Put the transmission in ”P” er as soon as possible. and apply the parking brake. Turn off When the engine is running, keep the air conditioning if it is being used.
Page 215 Never get under the vehicle when system. You should have it checked as oughly. the vehicle is supported by the jack soon as possible at your Toyota dealer. alone. CAUTION Use the jack only for lifting your vehicle during wheel changing.
Page 216 ’02 L/C U (L/O 0108) —Required tools and spare tire NOTICE Do not continue driving with a de- flated tire. Driving even a short dis- tance can damage a tire and wheel beyond repair. 1. Get the required tools and spare Turn the jack joint by hand.
Page 217 ’02 L/C U (L/O 0108) To remove the spare tire under the lug- When connecting a jack handle extension 2. Remove the access hole cover on the gage compartment: with a jack handle end, use a Phillips− rear bumper with a flat−bladed screw- head screwdriver or jack handle to tighten driver.
Page 218 ’02 L/C U (L/O 0108) 3. Insert the jack handle end into the low- 4. After the tire is lowered completely to When storing the spare tire, put it in place ering screw through the access hole the ground, remove the holding bracket with the outer side of the wheel facing up and turn it counterclockwise with push- as shown in the illustration.
Page 219 ’02 L/C U (L/O 0108) —Blocking the wheel —Removing wheel ornament —Loosening wheel nuts 2. Block the wheel diagonally opposite 3. Remove the wheel ornament. 4. Loosen all the wheel nuts. the flat tire to keep the vehicle from Pry off the wheel ornament, using the Always loosen the wheel nuts before rais- rolling when it is jacked up.
Page 220: Positioning The Jack
’02 L/C U (L/O 0108) —Positioning the jack JACK POINTS: Front—Under the frame side rail Left rear—Under the rear axle housing Right rear—Under the bracket on the rear axle housing Make sure the jack is positioned on a level and solid place. Put a jack handle, jack handle extensions, and jack handle end together as shown in the illustration.
Page 221 ’02 L/C U (L/O 0108) —Raising your vehicle CAUTION Never get under the vehicle when the vehicle supported jack alone. When connecting a jack handle extension 6. After making sure no one is in the with another extension and a jack handle vehicle, raise it high enough so that end, use a Phillips−head screwdriver or the spare tire can be installed.
Page 222: Changing Wheels
’02 L/C U (L/O 0108) —Changing wheels —Reinstalling wheel nuts 7. Remove the wheel nuts and change Before putting on wheels, remove any cor- 8. Reinstall all the wheel nuts finger tires. rosion on the mounting surfaces with a tight. wire brush or such.
Page 223 ’02 L/C U (L/O 0108) —Lowering your vehicle —Reinstalling wheel ornament CAUTION When lowering the vehicle, make sure all portions of your body and all oth- er persons around will not be injured the vehicle is lowered to the ground. 9.
Page 224 11. Check the air pressure of the re- If towing is necessary, we recommend (a) Towing with wheel lift type truck— placed tire. you have it done by your Toyota dealer or a commercial tow truck service. In Adjust the air pressure to the specification —From front consultation with them, have your ve- designated in Section 8.
Page 225: Emergency Towing
’02 L/C U (L/O 0108) —Emergency towing (a) Towing with wheel lift type truck (c) Towing with sling type Use a towing dolly under the wheels not truck lifted by the truck. (b) Using flat bed truck Front (c) Towing with sling type truck NOTICE Do not tow with sling type truck, ei- ther from the front or rear.
Page 226 ’02 L/C U (L/O 0108) If towing is necessary, we recommend CAUTION CAUTION you to have it done by your Toyota dealer or a commercial tow truck ser- Use extreme caution when towing ve- If the engine is not running, the pow- vice.
Page 227 If the towing vehicle can hardly move, do not forcibly continue the towing. Contact your Toyota dealer or a commercial tow truck service for assistance. Tow the vehicle as straight ahead as possible.
Page 228: Transmission Selector Lever
Toyota dealer if you can give them the key number and master key. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- liser system must be replaced.
Page 229 CORROSION PREVENTION AND APPEARANCE CARE Protecting your Toyota from corrosion ......Washing and waxing your Toyota .
Page 230 Now, it is up to you. Proper more harm than good to simply wet the High ambient temperatures can cause care of your Toyota can help ensure long− mud and debris without removing them. corrosion to those components of the term corrosion prevention.
Page 231 ’02 L/C U (L/O 0108) Washing and waxing your Toyota Check the interior of your vehicle. Wa- Washing your Toyota 1. Rinse off loose dirt with a hose. Re- ter and dirt can accumulate under the move any mud or road salt from the...
Page 232 4. To prevent water spots, dry the vehicle precautions. Be sure to polish and wax ing your Toyota through an automatic using a clean soft cotton towel. Do not the chrome trim as well as the paint.
Page 233: Cleaning The Interior
’02 L/C U (L/O 0108) Cleaning the interior NOTICE NOTICE CAUTION Do not use solvent, thinner, gasoline z Do not use dye or bleach on the Do not wash the vehicle floor with or window cleaner on the interior. belts—it may weaken them. water, or allow water to get onto the z Do not use the belts until they be- floor when cleaning the vehicle interi-...
Page 234 If you have any questions about the leather these could cleaning of your Toyota, your local cause discoloring. Toyota dealer will be pleased to answer them. z Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather.
Page 235 ’02 L/C U (L/O 0108) SECTION VEHICLE MAINTENANCE AND CARE Maintenance requirements ........General maintenance .
Page 236: Maintenance Requirements
See ”Owner’s War- form them are presented in Section 7. or if you prefer, your Toyota dealer will be ranty Information Booklet” or ”Owner’s pleased to do them at a nominal cost.
Page 237: General Maintenance
Information Booklet” or ”Owner’s Manual should investigate the cause or take your check the nuts for looseness. Tighten Supplement” for the details. vehicle to your Toyota dealer or a quali- them if necessary. fied service shop immediately. It is recom- Tire rotation...
Page 238 ’02 L/C U (L/O 0108) INSIDE THE VEHICLE Seat belts Automatic transmission ”Park” mecha- Check that the seat belt system such as nism Items listed below should be checked buckles, retractors and anchors operate Check the lock release button of the se- regularly, e.g.
Page 239: Does Your Vehicle Need Repairing
If you notice any of these clues, take your el lines on the case. Add only distilled tant clues are as follows: vehicle to your Toyota dealer as soon as water when replenishing. See Section 7−3 Engine missing, stumbling, or pinging possible.
Page 240: Emissions Inspection And Maintenance (I/M) Programs
Toyota dealer comes on. In this case, your vehicle may to prepare the vehicle for re−testing. not pass the I/M test and need to be repaired.
Page 241 ’02 L/C U (L/O 0108) SECTION − DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview ....... Fuse locations .
Page 242: Engine Compartment Overview
’02 L/C U (L/O 0108) Engine compartment overview 1. Engine oil filler cap 2. Brake fluid reservoir 3. Fuse blocks 4. Battery 5. Windshield and rear window washer fluid tank 6. Engine oil level dipstick 7. Condenser 8. Electric cooling fan 9.
Page 243: Fuse Locations
’02 L/C U (L/O 0108) Fuse locations Spare fuses...
Page 244: Do−It−Yourself Service Precautions
Toyota Warranty statement for details and boots, etc.—will be hot. So be care- suggestions. ful not to touch them. Oil, fluids This part gives instructions only for those and spark plugs may also be hot.
Page 245 ’02 L/C U (L/O 0108) z Use only spark plugs of the speci- Do not get under your vehicle with Dispose of used oil and filter only fied type. Using other types will just the body jack supporting it. Al- in a safe and acceptable manner.
Page 246: Parts And Tools
Parts (if level is low): Parts (if replacement is necessary): nance. Remember all Toyota parts are de- SAE J1703 or FMVSS No.116 DOT 3 Fuse with same amperage rating as signed in metric sizes, so your tools must...
Page 247 ’02 L/C U (L/O 0108) SECTION − DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level ....... . . Checking the engine coolant level .
Page 248: Checking The Engine Oil Level
’02 L/C U (L/O 0108) Checking the engine oil level 4. Pull the dipstick out and look at the oil Low level Full level level on the end. NOTICE Make sure to hold a rag under the dipstick, to avoid spilling drops of engine oil when you pull it out.
Page 249 ’02 L/C U (L/O 0108) ENGINE OIL SELECTION NOTICE Use API grade SJ “Energy−Conserving, SL z Be careful not to drop the engine “Energy−Conserving” or ILSAC multigrade oil on the vehicle components. engine oil. z Avoid overfilling, engine Recommended viscosity (SAE): could be damaged.
Page 250: Checking The Engine Coolant Level
Follow the manufac- turer’s directions for how much to mix If you can find no leak, have your Toyota with plain water (preferably demineralized dealer test the cap pressure and check water or distilled water). The total capacity for leaks in the cooling system.
Page 251: Checking The Radiator And Condenser
Checking brake fluid We recommend to use 50% solution for If any of the above parts are extremely your Toyota, to provide protection down to dirty or you are not sure of their condi- about −35_C (−31_F). When it is extreme- tion, take your vehicle to Toyota dealer.
Page 252: Checking Power Steering Fluid
’02 L/C U (L/O 0108) Checking power steering fluid If the level is low, add SAE J1703 or NOTICE FMVSS No. 116 DOT 3 brake fluid to the brake reservoir. If you spill the fluid, be sure to wipe If cold If hot it off to prevent it from damaging the O.K.
Page 253: Checking Tire Pressure
If the caps If a tire frequently needs refilling, have it have been lost, have new ones put on checked by your Toyota dealer. as soon as possible.
Page 254: Checking And Replacing Tires
Any tires which are over 6 years old must be checked by a qualified techni- Toyota recommends all four tires, or at cian even if damage is not obvious. least both front or rear tires be re- Tires deteriorate with age even if they CHECKING YOUR TIRES placed as a set.
Page 255: Rotating Tires
SNOW TIRE SELECTION If you need snow tires, select the same size, construction and load capacity as the original tires on your Toyota. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for To equalize tire wear and help extend possible restrictions.
Page 256 ’02 L/C U (L/O 0108) Regulations regarding the use of tire CAUTION chains vary according to location or Side chain type of road, so always check them Do not drive with the snow tires before installing chains. incorrectly inflated. NOTICE Never drive over 105 km/h (65 mph) with any type of snow tires.
Page 257: Replacing Wheels
Correct replacement wheels are available When driving with chains installed, at your Toyota dealer. be sure to drive carefully. Slow down before entering the curves to A wheel of a different size or type may avoid losing control of the vehicle.
Page 258: Aluminum Wheel Precautions
1600 km (1000 miles). When using tire chains, be careful not to damage the aluminum wheels. Use only the Toyota wheel nuts and wrench designed for your aluminum wheels. When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.
Page 259 ’02 L/C U (L/O 0108) SECTION − DO-IT-YOURSELF MAINTENANCE Electrical components Checking battery condition ........Battery recharging precautions .
Page 260: Checking Battery Condition
’02 L/C U (L/O 0108) Checking battery condition— —Precautions —Checking battery exterior CAUTION If electrolyte gets on your skin, Ground cable Terminals thoroughly wash the contact area. If BATTERY PRECAUTIONS you feel pain or burning, get medi- cal attention immediately. The battery produces flammable and explosive hydrogen gas.
Page 261: Battery Recharging Precautions
Charging necessary. Have battery Dark White checked by your NOTICE Toyota dealer. Never recharge the battery while the Clear or Have battery engine is running. Also, be sure all light checked by your accessories are turned off.
Page 262: Checking And Replacing Fuses
’02 L/C U (L/O 0108) Checking and replacing fuses Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. Type A If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good.
Page 263: Adding Washer Fluid
Add washer gain access to the bulbs. When replacing tem. Have your Toyota dealer correct it as fluid. a bulb, make sure the ignition switch and soon as possible.
Page 264 ’02 L/C U (L/O 0108) —Headlights The inside of the lens of exterior lights Bulb Light bulbs Type such as headlights may temporarily fog up when the lens becomes wet in the rain or Rear turn signal 7440 in a car wash. This is not a problem lights because the fogging is caused by the Stop/tail lights...
Page 265 If the connector is tight, wiggle it. LEFT–HAND HEADLIGHT: Install washer inlet securely. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 266 If the connector is tight, wiggle it. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 267 ’02 L/C U (L/O 0108) —Front turn signal and front side marker lights —Parking lights – – Use a Phillips head screwdriver. Use a Phillips head screwdriver.
Page 268 ’02 L/C U (L/O 0108) —Stop and tail lights Use a Phillips–head screwdriver.
Page 269 ’02 L/C U (L/O 0108) —Rear turn signal, stop/tail, and back–up lights —License plate lights Use a flat−bladed screwdriver. a: Back–up light b: Rear turn signal light c: Stop/tail light...
Page 270 ’02 L/C U (L/O 0108)
Page 271 ’02 L/C U (L/O 0108) SECTION SPECIFICATIONS Dimensions and weight ........Engine .
Page 272: Dimensions And Weight
’02 L/C U (L/O 0108) Dimensions and weight Engine Fuel Overall length mm (in.) 4890 (192.5) Model: Fuel type: 2UZ−FE Unleaded gasoline, Octane Rating 87 Overall width mm (in.) 1940 (76.4) (Research Octane Number 91) or higher. Type: ∗ 1 Overall height mm (in.) 1875 (73.8)
Page 273: Service Specifications
Spark plug type: Coolant type: Fluid type: DENSO SK20R11 Automatic transmission fluid D–II ”TOYOTA Long Life Coolant” or equivalent IFR6A11 DEXRON III (DEXRON With ethylene−glycol type coolant for a Spark plug gap, mm (in.): TRANSFER proper corrosion protection of aluminum 1.1 (0.043) components Oil capacity, L (qt., Imp.
Page 274: Tires
’02 L/C U (L/O 0108) Tires Oil type: BRAKES Tire size: Standard differential P275/70R16 114S Minimum pedal clearance when depressed Hypoid gear oil API GL−5 with the force of 490 N (50 kgf, 110 lbf) Tire pressure, kPa (kgf/cm or bar, psi): Limited−slip differential with the engine running, mm (in.): Normal driving...
Page 275: Fuses
’02 L/C U (L/O 0108) Fuses Engine compartment Engine compartment Left side kick panel Fuses (type A) 7. CDS FAN 20 A: Electric cooling fan 13. AM2 30 A: Starting system, multiport fuel injection system/sequential multi- 1. ALT−S 7.5 A: Charging system 8.
Page 276 ’02 L/C U (L/O 0108) 16. HEAD (RH−UPR) 20 A: Right−hand 26. GAUGE 15 A: Gauges and meters, 38. ECU−IG 15 A: Anti−lock brake system, headlight (high beam) service reminder indicators and warning shift lock system, power seats, power buzzer (except discharge, open door antenna, power tilt...
Page 277 ’02 L/C U (L/O 0108) 49. AM1 NO.1 80 A: Charging system, all components in ”AM1 NO.2”, ”GAUGE”, ”WIPER”, ”DIFF”, ”A.C” ”SEAT HTR” fuses 50. HTR 60 A: Air conditioning system...
Page 278 ’02 L/C U (L/O 0108)
Page 279 ’02 L/C U (L/O 0108) SECTION REPORTING SAFETY DEFECTS FOR U.S. OWNERS AND UNIFORM TIRE QUALITY GRADING Reporting safety defects for U.S. owners ..... . Uniform tire quality grading .
Page 280 Transportation, Washington, D.C. quality grading. notifying Toyota Motor Sales, 20590. You can also obtain other Your Toyota dealer will help answer any U.S.A., Inc. (Toll−free: information about motor vehicle questions you may have as you read this 1−800−331−4331). safety from the Hotline.
Page 281 ’02 L/C U (L/O 0108) Tread wear—The tread wear grade is a Temperature A, B, C—The temperature comparative rating based on the wear rate grades are A (the highest), B, and C, of the tire when tested under controlled representing the tire’s resistance to the conditions on a specified government test generation of heat and its ability to dissi- course.
Page 282 ’02 L/C U (L/O 0108)
Page 283 ’02 L/C U (L/O 0108) U −7 Quick index D If a service reminder indicator or warning buzzer comes on ..D If your vehicle will not start ........D If your engine stalls while driving .
Page 284 The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.
Page 285 English, may be purchased as applicable from work yourself step−by−step. any Toyota dealer. Areas covered include such things as spark plug re- Pub. Name: 2002 LAND CRUISER Repair placement, valve clearance adjustment and engine oil Manual and filter replacement.
Page 286 The system will provide both a visual map and audio in- The Toyota Navigation System is one of the structions. The audio instructions will an- most technologically advanced vehicle ac- nounce the distance and direction to go cessories ever developed.
Page 288 When you start the engine or turn the ignition key to ”ACC”, the initial ”TOYOTA” screen appears and the system begins operating. NOTICE This is a warning against something...
Page 289 UN002 Please read it and follow the instructions. If a screen other than for the navigation sys- tem is displayed (i.e., for the trip information screen), the current screen would change to the ”CAUTION” screen by pushing the ”MAP/VOICE” ”DEST” ”MENU”...
Page 290 Safety Instruction Before attempting to use this system while CAUTION you are driving, learn how to use it and be- come thoroughly familiar with it. Read the D For safety, the driver should not entire Navigation System Manual to make operate the navigation system while sure you understand the system.
Page 291 While you are driving, listen to the voice in- We recommend that you obtain updated structions as much as possible and glance at map data, when it becomes available, in or- the screen briefly and only when it is safe. der to help use the system as effectively and However, do not totally rely on voice guid- safely as possible.
Page 292 Overview of Touch Screen and Switches Switch operation This system operates mainly by the INFORMATION switches on the screen. To protect the screen, lightly touch switches on the D If the system does not respond to a screen with your finger. When you touch touch of a switch, move your finger a switch on the screen or push the button, away from the screen and then touch...
Page 293 Symbols, Switches and Buttons North−up symbol and scale INFO button of map Push this button to display the To indicate a map view with information menu screen. For North up. Touching this sym- details, see page 68. bol changes the map view to a heading−up respective.
Page 294 Heading−up symbol One − touch registra- s−008u and scale of map tion of marked point To register the current vehicle position as a On the map, the vehicle travel direction is up. marked point. For details, see page 56. The red arrow indicates North. Touching this symbol directly on the screen changes the map to North−up.
Page 295 SECTION OTHER FUNCTIONS Screen transition ..........Screen adjustment .
Page 296 Screen transition1. Screen adjustment2. The function returning to the previous You can adjust the brightness or contrast screen from the audio or air conditioner of the screen depending on the bright- screen is selectable. ness of your surroundings. You also can turn the display off.
Page 297 UNG407 UNX401 Color and tone adjustment Depending on the position of the head- light switch, the screen changes to the You can adjust the color and the tone while day mode or night mode. the DVD video and Video CD are being played.
Page 299 SECTION BASIC FUNCTIONS Descriptions of basic operations in frequent use Inputting letters and numbers ........How to move the cursor .
Page 300: Inputting Letters And Numbers
Inputting letters and numbers ”List” The navigation system operates by Touching the switch will change the switches on the screen and on the bezel. screen to a display of the database items that When you touch a switch, a beep sounds. match the name or address that you have When using the switches on the touch entered on the screen.
Page 301: How To Move The Cursor
How to move the cursor If a or a appears to the right or left of the item name, the complete name is too long for the display. Touch the name, UN008 UN009 and the name will scroll to the end or beginning of the name.
Page 302: Destination Input
Destination input ”DEST” Address: You can enter the house number, Push the button on the bezel and the street address and selected city of your the ”Destination” screen appears. destination. You can find your destination using various methods. See page 6 UN011 through 8 for the detailed steps.
Page 303 5. By Home: You can select your own home D When setting the destination, you INFORMATION without entering the address each time. In should use the map on a scale of one this case, it is necessary to register your D When inputting the destination, the half mile or smaller.
Page 304 Destination input by (a) Inputting a house number ADDRESS and a street name ”Address” Touch the switch on the destination screen. The ”Address” screen appears, and then you can input a house number. Touch letters directly on the screen to in- UN012 put a house number.
Page 305 (b) Inputting a city name The screen for inputting a city name appears ”City” if you touch the switch on the ”Ad- dress” screen on page 6. UN014 UN303−1 UN015 When you find your desired street name, If you input a street name first, the screen touch of the item.
Page 306 Destination input by POINT (a) Input the name of the OF INTEREST point of interest directly ”Point of Interest” There are 3 ways to select a point of in- Touch the switch terest location. on the destination screen. (a) Input the name of the point of interest directly.
Page 307 (c) Selection from the Points of (b) Inputting a city name Interest categories ”City” ”Category” Touch the switch on the point of Touch the switch on the interest screen. point of interest screen. UN018 UN020 UN019 Touch the of your desired destina- tion.
Page 308 UN023 UN021 UN022 Once you have selected a category, touch If you do not know the name of the specific When you touch the of your desired letters directly on the screen to input a name. point of interest, for example, when you are item, the screen changes and displays ”0–9”...
Page 309 LIST OF POINTS OF INTEREST Mexican Restaurant UN201 Seafood Japanese Shopping ”Info” Touch the switch on the screen to Chinese display the selected destination name, ad- Grocery Store dress and telephone number. French INFORMATION Gas Station The desired point of interest can be dis- Italian played on the map screen.
Page 310 TOYOTA Dealerships Sports Complex Hospital (all search areas) LEXUS Dealerships Park/Recreation Casino (all search areas) (all search areas) Civic/Community Center Automobile Club Marina Convention/Exhibition Auto Service & Tourist Attraction Center Maintenance (all search areas) Hotel Winery Court House Golf Course...
Page 311 Destination input by MARKED POINT ”Marked Point” Touching the switch on the destination screen displays your Commuter Rail Station Bank list of registered marked points. See page 52 on registering and editing marked points. Ferry Terminal School Park and Ride UN024 Rest Area Higher Education...
Page 312: Previous Destination
Destination Input by PREVIOUS DESTINATION ”Previous Destination” There are 4 ways to list the marked point You can delete the list of previous destina- Touch the by touching switches on bottom of the tions while you stop your car, if you no longer switch on the destination screen.
Page 313 Destination input by Destination input by HOME EMERGENCY ”Home” ”Emergency” Touch the switch on the des- By touching the switch tination input screen. on the destination input screen, the dis- play changes to a screen to select police The screen changes and displays the stations, hospitals or dealers.
Page 314 Destination input by INTERSECTION ”Intersection” Touch the switch on INFORMATION the destination screen. UN029 The navigation system does not guide in areas while route guidance is un- available. (See page 38.) UN028 Touch the of your desired item. After inputting the two intersecting streets, the screen changes and displays the map Input the name of the two intersecting location of the selected destination and...
Page 315 Destination input by FREEWAY ENTRANCE or EXIT To input a freeway entrance or exit, touch ”Fwy Entrance/Exit” switch on UN031 the destination input screen. EMV3111U UN030 Select the desired freeway by touching If the same two streets cross at more than one intersection, the screen changes and Be sure to use the complete name of the displays the menu to select the city name...
Page 316 Destination input by PREVIOUS STARTING POINT ”Previous Starting There are 2 ways to list the freeway en- Touch the trance or exit. Point” switch on the destination screen. Dist Sort: Touch this switch to list the en- UN033 The screen changes and displays the trances or exits in order of distance from your map location of the previous starting current location.
Page 317: Entering Destination
Destination input by MAP Entering destination ”Map” After you input the destination by one of You are given a number of choices on the Touch the switch on the destina- the ten methods, the screen changes and conditions which the system uses to deter- tion screen.
Page 318: Route Guidance Screen
Route guidance screen Route 1: A route on which you can reach the The route guidance system displays two destination in the shortest time. different screen modes. Route 2: A route on which you can reach the UN037 destination in the shortest distance. Route 3: Other route.
Page 319 POI: Touch this switch, and symbols of Chg. Route: The ”Change Route” screen points of interest are shown on the screen. appears and the following settings are avail- (For details, see page 29.) able. Mark: Touch this switch for one−touch regis- UN040 tration of the marked point.
Page 320: Current Position Display
Current position display INFORMATION INFORMATION If the calculated route includes a trip by When you use the ”one−touch” scroll ferry, the route guidance shows a sea feature, the current vehicle position route. After you travel by ferry, the cur- mark may disappear from the screen. UN042 rent vehicle position may be incorrect.
Page 321: Voice Guidance
Voice guidance Typical voice guidance prompts Voice route guidance is offered automati- You can listen to ”Voice route guidance” by cally during route guidance. Use voice ”MAP/VOICE” pushing the button on the guidance just for your reference. bezel, even if the volume is ”OFF”. You can adjust the volume of the voice or turn off voice guidance.
Page 322 INFORMATION On freeways, interstates or other high- ways with higher speed limits, the voice guidance will be made at earlier EMV3113U EMV3114U points than on city streets in order to al- low time to maneuver. : The system indicates a U−turn if the dis- ”Proceed about 4 miles to the traf- tance between two one−way roads (of oppo- fic circle.”...
Page 323 INFORMATION D If the system cannot determine the current vehicle position correctly (in cases of poor GPS signal reception), EMV3115U EMV3116U the voice guidance may be made ear- ly or delayed. D If you did not hear the voice guid- ”MAP/ ance command, push the VOICE”...
Page 324: Registration Of Your Home
Registration of your home ”Regis- (a) Registering by current position If you register your home address before- If home is already registered, the hand, you can easily set the route back to ter” switch is dimmed. When you select this method, the current your home.
Page 325: Detour Setting
Detour setting (d) Deleting the registration of your The screen changes and displays the map When you are driving while the route location of the home and a message. If you guidance is operating, you can change home are sure that you want to delete the point, the route to detour around a section of ”YES”...
Page 326 INFORMATION chg−route D When your vehicle is on a freeway, the detour distance selections are 5, 15, and 25 miles. EMV3065U D The system may not be able to calcu- late a detour route depending on the selected distance and surrounding road conditions.
Page 327: Displaying Points Of Interest
Displaying points of interest Points of interest such as gas stations A window with a limited choice of points of in- and restaurants can be displayed on the terest will be displayed. When you touch map screen. You can also set their loca- your desired type of point of interest, sym- tion as a destination and use them for bols will appear on the map screen indicating...
Page 328: Turn List
Turn list The name of the point of interest and the You can change from the map screen to Setting a POI as a destination ”Info” a ”Turn List” screen that displays the list switch on the screen are displayed You can select one of the points of inter- of the roads up to your destination.
Page 329 INFORMATION D The current vehicle position mark UN058 UN057 appears at the bottom of the screen next to the name of the street you are driving on. The mark does not move. D If you leave the guidance route, the name of the street you are on is not shown on the list next to the current vehicle position mark.
Page 330: Guidance Screen
Guidance screen You can change half of the screen to the Arrow screen ”Map/ Guidance Screen by touching the Guide” switch while the map screen is displayed. You can choose one out of two types of Guidance Screen. UN065 UN066 UN059 2.
Page 331: Map Scale
Map scale Turn list screen The map scale is displayed under the North− up symbol or Heading−up symbol at the top left of the screen. INFORMATION UN063 When the map scale is at the maximum UN067 ”zoom OUT” range of 64 miles, the switch is dimmed.
Page 332: Screen Scrolling
Screen scrolling Orientation of the map ”Mark” ”POI” If you touch switches like etc., the screen does not scroll and the re- UN061 spective functions operate. UN064 After scrolling the screen, the map remains centered at the selected location until you activate another function.
Page 333: Limitations Of The Navigation System
Limitations of the navigation system You can change the orientation of the This navigation system calculates the map from North−up to Heading−up by current vehicle position using satellite touching the direction symbol at the top signals, various vehicle signals, map left of the screen.
Page 334 (a) Accurate current vehicle position may not be shown in the following cases: The GPS satellites may not send signals due D When driving on a small angled Y− D When the tires are worn. to repairs or improvements being made to shaped road.
Page 335 D During automatic rerouting, the route may specified tires for your Toyota. Installing tires not be changed. that are larger or smaller than the originally equipped diameter may cause inaccurate D The route in a U−turn may be shown or...
Page 336: Map Database Information And Updates
Map Database information and updates Map database is made based on the There are two types of areas available for In order to provide you with accurate map in- maps, 2001 edition of DENSO, whose in- route guidance. (See the following formation as much as possible, we are al- formation source comes from NavTech pages.) In one type of area, primarily...
Page 337 “Menu” screen. The ”System Option” screen appears and displays the INFORMATION map database version date. Contact your For the updated map DVD−ROM, con- dealer to find out if there is a more recent up- tact your Toyota dealer. date released.
Page 338 Route guidance availability DCA1 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 339 Route guidance availability DCA2 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 340 Route guidance availability DCA3 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 341 Route guidance availability DCA4 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 342 Route guidance availability DCA5 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 343 Route guidance availability DCA6 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 344 Route guidance availability DCA7 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 345 Route guidance availability DCA8 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 346 Route guidance availability DCA9 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 347 Route guidance availability DCA11 2000 by NavTech Route guidance available areas Route guidance available for main roads only...
Page 349 SECTION ADVANCED FUNCTIONS Descriptions of functions for more effective use Marked points ........... . Way points .
Page 350: Marked Points
Marked points39. (a) Registering marked points You can register and keep your own marked points of interest list (like restau- UN078 rants, sports facilities, etc.) and use the marked points to input a destination. UN080 ”MENU” 1. Push the button on the bez- A screen similar to that for destination input el to display the menu screen and touch appears.
Page 351 (b) Editing marked points Once a marked point is registered, you can edit the icon, name or telephone UN081 number. UN083 ”MENU” 1. Push the button on the bez- el to display the menu screen and touch ”Marked Point” switch UN082 The screen lists the marked points.
Page 352 Sound Icon: When you set on these icons, D Editing a ”Phone” (telephone number) the buzzer sounds as your vehicle ap- proaches them. UN084 UN087 When you touch the desired symbol or ”Back” , the previous screen is displayed. D Editing a ”Name” UN086 Touch the item to edit (on the left side of the screen).
Page 353 (c) Deleting marked points ”MENU” D Editing a ”Position” (position/map 1. Push the button on the bez- To delete only specified marked points, use ”Mark” ”Date”, ”Name” location). el to display the menu screen and touch ”Marked Point” ”Dist” switch. switch to display the screen, so that you can easily find the marked points.
Page 354 (d) One−touch marked point registration41. If you want to register a new point, touch the ”YES” switch and delete several old points. See ”(c) Deleting marked points”. UN092 UN094 If you do not want to delete the points already ”NO” registered, touch the switch.
Page 355: Way Points
Way points42. (a) Setting a way point (b) Adding a way point ”Set” ”Add” 1. Touch the switch. 1. Touch the switch to display the Add Way Point screen. UN096 UN098 UN099 You can set way points during route guid- ”Chg.
Page 356 (c) Deleting a way point ”Delete” 1. Touch the switch to display the Delete Way Point screen. UN100 UN102 UN101 3. Add a way point in the same way as 3. A selected point and above message you input the destination. appear.
Page 357: Avoid Point/Area
(d) Deleting the next way point Avoid Point/Area43. Any points/areas you want to avoid due INFORMATION to traffic jams, construction work or other reasons can be registered as avoid D Some areas and freeways may not points/areas. be able to be set as an avoid point. ”MENU”...
Page 358 ( a) Registering avoid point/area (b) Editing avoid points ”Register Avoid Point/ ”Edit Avoid Point/ 1. Touch the 1. Touch the Area” Area” switch. switch to display the Edit Avoid Point/Area screen. UN105 UN107 UN104 3. Depending on the contents to be ”Reduce”...
Page 359 (c) Deleting avoid point/area ”Delete Avoid Point/ 1. Touch the Area” UN111 switch to display the Delete Avoid Point/Area screen. UN108 UN109 3. Depending on the contents to be 3. Either of the above messages appears. ”Reduce” edited, touch either the ”YES”...
Page 360: Current Position Calibration
Current position calibration44. D Position/Direction The current vehicle position mark will be automatically corrected during driving UN113 on reception of GPS signals. If your ve- hicle cannot receive GPS signals, you UN114 can correct the current position mark manually. UN112 ”Position”...
Page 361 D Distance The distance calibration function is to be used when the tires are replaced. This will adjust for any possible change in tire UN115 circumference from the old tires to the new ones. If this procedure is not per- formed when tires are replaced, the cur- rent vehicle position mark may become incorrect.
Page 363 SECTION MORE ADVANCED FUNCTIONS Convenient features Automatic rerouting ..........Time to destination .
Page 364: Automatic Rerouting
Automatic rerouting Time to destination When the ”Automatic Rerouting” feature When the ”Time to Destination” feature is is turned on, the system will automatical- turned on, the time required to reach the ly search for a new route to the destina- destination is displayed on the route UN118 tion if you leave the guidance route.
Page 365 INFORMATION D The displayed time to the destination UN120 is the approximate driving time cal- UN122 culated based on the speeds you se- lected and your actual position along the guidance route. D The time shown may vary greatly de- pending on your progress along the route (which may be affected by road ”Guidance Setup”...
Page 366: Maintenance Information
Maintenance information UN124 UN126 ”INFO” This system has a function which informs 1. Push the button on the bezel Date: Input the next maintenance date. you of the time to replace certain parts or to display the information menu screen, Distance: Input the driving distance until the ”Maintenance”...
Page 367 ”OFF” Information items Touch the switch at the top of the screen, and the information screen will no longer be displayed. Scheduled Maintenance Replace Engine Coolant INFORMATION Oil Change Replace Brake Fluid D For scheduled maintenance infor- mation, please refer to the ”Sched- uled Maintenance Guide”...
Page 368: Dealer Setting
Dealer setting (a) Registering dealer Maintenance UN128 ”Register Dealer” 3. After you enter your dealer, the screen You can register your dealer’s name and 1. Touch the changes and displays the map location of ”Dealer” switch. address. Touch the switch on ”Enter”...
Page 369 (b) Editing dealer D Editing a ”Dealer” or a ”Staff” D Editing a ”Position” UN130 UN133 UN132 UN133t ”Edit Dealer” 1. Touch the switch. Touch alphabet or numeral keys directly Touch the arrows to scroll to your desired to input the name. point on the map screen.
Page 370 (c) Deleting dealer (d) Going to dealer D Editing a ”Phone” (telephone number) The registered dealer can be set as a des- tination. UN135 UN134 ”Delete Dealer” 1. Touch the switch. Touch numeral keys directly. ”Go to Dealer” Touch the switch.
Page 371 SECTION AIR CONDITIONING Automatic air conditioning controls ........
Page 372 Automatic air conditioning controls Page 1. Air conditioning operation screen display button ... 2. Driver side temperature control button ....3.
Page 373 "Air flow selection See ”Lower vent” on page 81.
Page 374 (a) Climate control "The automatic air conditioning auto- SETTING OPERATION − automatic con- Push the ”OFF” button to turn the air condi- matically maintains the set tempera- trol tioning off. ture. It is recommended that you close the lower This air conditioning features automatic vent.
Page 375 SETTING OPERATION − manual control Floor − Air flows mainly from the floor vents. When one of the manual control buttons is depressed while operating in automat- It is recommended that you close the lower ic mode, the mode relevant to the de- vent.
Page 376 If manual fan speed control is desired − If manual switching of air intake is de- For normal use, it is best to keep the air in- sired − take control button set to OUTSIDE AIR mode. If recirculated air is used during heat- ing, the windows will fog up more easily.
Page 377 If the indicator of the ”A/C” button control button until maximum figure ap- blinks even when the ”A/C” button is pushed pears on the temperature display. again, have the compressor checked by 2. Push the ”FRONT WINDSHIELD” but- your nearest Toyota dealer. ton.
Page 378 (c) Rear air conditioning switch 3. Push the ”HI” of the air flow control switch to obtain a maximum air flow. CAUTION 4. Leave the air conditioning on−off button Do not use the ”FRONT WINDSHIELD” off. button during cooled air operation in UNC505 For further information for removing frost and extremely humid weather.
Page 379 Center vents Side vents Lower vent I17070 I17028 I17029 The center vents may be opened or The side vents may be opened or closed The lower vent may be opened or closed closed as shown. as shown. as shown. For removing frost or fog, it is recommend that you close the lower vent when you use the “Floor”, the “Floor/Windshield”...
Page 381 SECTION AUDIO SYSTEM Audio system ........... .
Page 382 Audio System Quick reference for your audio system Page 1. Audio operation screen display button ......2. Function switch display screen .
Page 383 Using your audio system: (a) Turning the system on and some basics This section describes some of the basic fea- tures of the audio system. Some information may not pertain to your system. Your audio system works when the ignition key is in the ”ACC”...
Page 384 (b) Tone and balance How good an audio program sounds to you is largely determined by the mix of the treble, mid−range, and bass levels. In fact, different kinds of music and vocal programs usually sound better with different mixes of treble, UNG604 mid−range, and bass.
Page 385 (c) Your radio antenna The antenna automatically extends when the radio is on or the radio RDS system is on, and retracts when the radio mode is off. UNG607 UNG608 I17003 Touching the ”SOUND” switch on the BASS ”+” or ”−”: Adjusts low−pitched screen displays the sound adjustment tones.
Page 386 (d) Your cassette player (e) Your automatic changer When you insert a cassette, the exposed tape should be to the right. NOTICE D To prevent damage to the antenna, NOTICE make sure it is retracted before driving your vehicle through an unc601 Do not oil any part of the cassette automatic car wash.
Page 387: Radio Operation
Radio operation The player is intended for use with 12 cm (4.7 (a) Listening to the radio in.) discs only. UNC610a UNG610 Turn this knob to step up the station band or to step down. Push these buttons to choose either an Your radio automatically changes to stereo AM or FM station.
Page 388 (b) Presetting a station (c) Selecting a station Your vehicle has an electronic tuning radio (ETR). Tune in the desired station using one of the following methods. Preset tuning: Touch the switch (1−6) or UNG604 push the ” ” or ” ” button of the ”CH” button UNG612 for the station you want.
Page 389 (d) RDS (Radio Data System) Preset scan tuning: Touch the ”SCAN” switch and hold it until you hear a beep. ”P. SCAN” appears on the display. The radio will tune in the next preset station up or down the band, stay there for a few seconds, and then UNG613 UNG614 move to the next preset station.
Page 390 (e) TYPE (Program type) If the traffic program station is found, the If in one program type, more than 6 stations name for traffic program station is displayed are found, the 6 stations are preset in the or- and ”TRAF” is lit for a while until traffic an- der of the lower frequency.
Page 391 (f) Emergency broadcast (g) Radio text message UNG616 UNG617 UNG618 If an emergency broadcast is received dur- If a new message is received with the first If ”MSG” appears during FM reception, ing reception of other than AM broadcasting, text message on the display, ”MSG” appears touching the ”MSG”...
Page 392 Cassette tape player operation To recall a radio text message, touch the (a) Playing a cassette tape ”RECALL” switch. Each time you touch the switch, the available messages will be dis- played beginning with the newest one. When you touch the ”OK” switch, the pre- UNG605 vious screen returns.
Page 393 (b) Manual program selection * Dolby noise reduction manufactured under If a tape rewinds completely, the cassette license from Dolby Laboratories Licensing player will stop and then play the same side. Corporation. ”DOLBY” and the double−D If a tape fast forwards completely, the cas- symbol are trademarks of Dolby Labora- sette player will play the other side of the tape...
Page 394 (c) Automatic program selection Touch the ”SKIP” switch. The player will au- When the end of the tape is reached, the tomatically skip any blank portions of 15 se- player automatically reverses sides and re- conds or more and play the next program. To sumes normal play.
Page 395 DVD player operation The DVD player can play audio CDs, DVD (a) Inserting discs video discs and video CDs. For safety reasons, you can enjoy DVD vid- eo discs and video CDs only when the ve- hicle is completely stopped with the ignition unc603 switch in the “ACC”...
Page 396 unx607 unx606 unx608 3. Pull out the tray while pushing the lock 4. Put a disc on the tray with its label face 5. Insert the magazine into the player as release button. up and push the tray back into the maga- indicated by the arrow ahead on the mag- zine.
Page 397 (b) Playing a disc (c) Selecting a desired disc CAUTION To reduce the chance of injury in case of an accident or a sudden stop, always keep the console box closed while driv- ing. unc620 unx609 Push the “DISC” button if the magazine is On the screen: Touch the desired disc already loaded in the player.
Page 398 (d) Operating an audio CD (ii) Selecting a desired track (iii) Searching for a desired track or a disc Playing an audio CD UNC622a unx012 unx610 Touch the “SCAN” switch. Push the number of the disc you want to “TRACK” button: Use for direct access to play.
Page 399 Touch the “DISK SCAN” switch. (iv) Other functions “RAND” switch: Use it for automatic and random selection of the disc which you are “DISC SCAN” will be highlighted in green. currently listening to. The program at the beginning of each disc will be played for 10 seconds.
Page 400 (e) Operating a DVD video disc DVD video discs Marks shown on DVD video discs: Precautions: The playback condition of This DVD player conforms to NTSC color some DVD video discs may be determined TV formats. The DVD video disc conform- indicates NTSC format by a DVD video software producer.
Page 401 (ii) DVD video disc glossary Multi−angle feature: You can enjoy the Manufactured under license from Dolby same scene at different angles. Laboratories. “Dolby”, “Pro Logic”, and DVD video discs: DVD in which animated the double−D symbol are trademarks of pictures are memorized. DVD video discs Multi−language feature: You can select a Dolby Laboratories.
Page 402 (iii) Precautions on DVD video disc (iv) Playing a DVD video disc (v) Displaying operation switches When recording with a DVD video or video CD, audio tracks may not record in some cases while the menu is displayed. As audio will not play in this case, verify that the video tracks are playing and then activate play- unx614...
Page 403 “Second Page” switch: Use this switch to (vi) Description of each switch “AA” switch: Touch this switch to fast re- display the operation switches on the sec- verse during the playback and reverse slow- D Switches on top page ond page. ly during the pause.
Page 404 (vii) Searching by title (viii)Changing the subtitle language (ix) Changing the audio language unx622 unx620 Enter the title number using “−”, “+” and Each time you touch “Sub Title”, the lan- Each time you touch “Audio”, the lan- “+10” switches and touch “Enter”. The guage is selected from the ones stored in guage is selected from the ones stored in player starts playing video for that title...
Page 405 (x) Changing the angle (xi) Setup menu D Subtitle language You can change the subtitle language. 1. Touch “Subtitle Lang.” 2. Touch a language you want to read on the “Select Subtitle Lang.” screen and unx619 unx617 “Enter”. If you cannot find a language you want to read on this screen, touch “Others”...
Page 406 D Angle mark (xii) Entry of language code 0618 French The multi−angle mark can be turned on or 0405 German off on the screen while the disc in which the multi−angle is memorized is being 0920 Italian played. 0519 Spanish Each time you touch “Angle Mark”, the unx618 angle mark on the display turns on or off...
Page 407 0201 Bashkir 0610 Fiji 1009 Yiddish 0205 Byelorussian 0615 Faroese 1023 Javanese 0207 Bulgarian 0625 Frisian 1101 Georgian 0208 Bihari 0701 Irish 1111 Kazakh 0209 Bislama 0704 Scots−Gaelic 1112 Greenlandic 0214 Bengali 0712 Galician 1113 Cambodian 0215 Tibetan 0714 Guarani 1114 Kannada 0218...
Page 408 1314 Mongolian 1823 Kinyarwanda 2007 Tajik 1315 Moldavian 1901 Sanskrit 2008 Thai 1318 Marathi 1904 Sindhi 2009 Tigrinya 1319 Malay 1907 Sangho 2011 Turkmen 1320 Maltese 1908 Serbo−Croatian 2012 Tagalog 1325 Burmese 1909 Sinhalese 2014 Setswana 1401 Nauru 1911 Slovak 2015 Tonga 1405...
Page 409 (f) Operating a video CD (ii) Displaying operation switches 2515 Yoruba Playing a video CD 2621 Zulu unx624 unx623 Push the number of the disc you want to play. When you touch the “PICTURE” switch, the unx625 video screen appears.
Page 410 If you touch the part where switches are not (iii) Description of each switch D Switches on second page located while you are watching video on the D Switches on top page “ ” switch: Use this switch to pause the video CD, video CD operation switches will video screen.
Page 411 If “NO DVD MAGAZINE” appears on the display: It indicates that the magazine is not inserted into the DVD player. If the malfunction is not rectified:Take your vehicle to your Toyota dealer.
Page 412 For example, nearby buildings and terrain Station swapping − If the FM signal you are D A dirty tape head or tape path can de- can interfere with FM reception. Power lines listening to is interrupted or weakened, and crease sound quality and tangle your cas- or telephone wires can interfere with AM sig- there is another strong station nearby on the sette tapes.
Page 413 Caring for your DVD player and discs D Bumpy roads or other vibrations may make your multi−disc player skip. D If moisture gets into your DVD player, you Audio CDs may not hear any sound even though your DVD player appears to be working. Re- move the magazine from the player and wait until it dries.
Page 414 D Your DVD player cannot play special shaped, labeled or low−quality discs as CAUTION those shown here. Do not use them as the player could be damaged. DVD players use an invisible laser beam which could cause hazardous D Handle discs carefully, especially when radiation exposure if directed outside you set them into the magazine.

Toyota 2002 Land Cruiser Owner's Manual

1 2 Section −

1 3 Section −

1 4 Section −

1 5 Section −

1 6 Section −

1 8 Section −

1 9 Section −

2 Section

6 Section

7 1 Section −

7 2 Section −

7 3 Section −

8 Section

Section 14

Section 15

Section 16

Quick Links

Chapters

Related Manuals for Toyota 2002 Land Cruiser

Summary of Contents for Toyota 2002 Land Cruiser