Picture Save Destination (Cards And Built-In Memory); Remaining Battery And Memory Capacity; Setting The Clock - Panasonic Lumix DMC-ZS1 Operating Instructions Manual

Inserting battery and card

Picture save destination (cards and built-in memory)

Pictures will be saved to a card if one is inserted, or to the built-in memory
Compatible memory cards (sold separately)
The following SD standard-based cards (Panasonic brand recommended)
• SD memory cards (8 MB - 2 GB)
• SDHC memory cards (4 GB - 32 GB)
Can only be used with devices compatible with SDHC
memory cards. (Always read your device's operating
instructions before proceeding)
• Cards of over 4 GB may only be used if they have the SDHC logo.
Please reformat the card with this camera if it has already
been formatted with a computer or another device. (P.26)
If the switch on the card is set to 'LOCK', operations such as
formatting, recording, and deleting cannot be performed.
MultiMediaCards may also be used (for pictures only)
Built-in memory (approx. 40 MB)
Built-in memory is slower than SD memory card.
'QVGA' in 'REC QUALITY' (P.80) only can be available to record motion pictures in the built-in memory.
Clipboard pictures (P.81) are saved to built-in memory.
Pictures may be copied between cards and the built-in memory (P.98).

Remaining battery and memory capacity

Remaining battery (only when using battery)
If the battery mark flashes red (or status indicator flashed when LCD
monitor is off), recharge or replace battery. (P.13)
Displayed when no card inserted (pictures will be saved to built-in memory)
Pictures remaining ( P.124 P.126)
When in operation
(Card) or (Built-in memory) are illuminated red.
This means that an operation is in progress, such as the recording, reading, deleting,
or formatting of pictures. Do not turn off the power or remove the battery, card, or AC
adaptor (DMW-AC5PP, sold separately) (this may cause damage to or loss of data).
Do not subject the camera to vibrations, impact, or static electricity. Should any of these
cause camera operation to be terminated, attempt to perform the operation again.
It is recommended that you copy important pictures to your computer (as
electromagnetic waves, static electricity, or faults may cause data to be damaged).
For model numbers and types,
see http://panasonic.co.jp/pavc/global/cs (This Site is English only.)
16
VQT1Z82
(Continued)
if not.
SD memory card/
SDHC memory card
(sold separately)
32 32 32
Switch
SDHC logo
(LOCK)
(flashes red)

Setting the clock

Set REC/PLAY switch to before turning on power.
REC/PLAY switch
To change time setting
Select 'CLOCK SET' from
SETUP menu (P.21), perform
and .
• Clock settings will be saved for
approx. 3 months even after
battery is removed, provided
a fully-charged battery was
installed in camera for the 24
hours beforehand.
To set local time at travel
destination
'WORLD TIME' (P.68)
Failure to set the date and time will cause the date/time to be improperly printed when printing
pictures in digital photo center or when using 'TEXT STAMP' (P.90).
Year can be set between 2000 and 2099.
After the time has been set, the date can be printed correctly even if the date is not displayed on the
camera screen.
( The clock is not set when the
camera is shipped.)
Turn on the power
'PLEASE SET THE CLOCK' will be displayed
when power is turned on for the first time.
While this message is displayed
' '
Press MENU/SET
Select the setting item (year,
month, date, time, display order,
time display format), and set.
Select the
setting
item
Set the
date, Select the display format
time, or
display.
• To cancel → Press .
• Setting example of display order and time display format
[M/D/Y] [24HRS]: 12:34 APR.15.2009
[D/M/Y] [AM/PM]: PM 12:34 15.APR.2009
[Y/M/D] [24HRS]: 2009.4.15 12:34
When set to [AM/PM], 0:00 midnight is AM 12:00,
and 0:00 noon is PM 12:00.
Set
' '
Press MENU/SET
• Turn on power again and check time display.
(Time and date can be displayed by pressing
'DISPLAY' several times.)
VQT1Z82
17