Yaesu FT-897 Operating Manual page 55

No Menu Item
040 DIG VOX
041 DISP COLOR
042 DISP CONTRAST
043 DISP INTENSITY
044 DISP MODE
045 DSP BPF WIDTH
046 DSP HPF CUTOFF
047 DSP LPF CUTOFF
048 DSP MIC EQ
049 DSP NR LEVEL
050 EMERGENCY
051 FM MIC GAIN
052 FM STEP
053 HOME-->VFO
054 LOCK MODE
055 MEM GROUP
056 MEM TAG
057 MEM/VFO DIAL MODE
058 MIC SCAN
059 MIC SEL
060 MTR ARX SEL
061 MTR ATX SEL
062 MTR PEAK HOLD
063 NB LEVEL
064 OP FILTER 1
065 PG A
066 PG B
067 PG C
068 PG ACC
069 PG P1
070 PG P2
071 PKT 1200
072 PKT 9600
073 PKT RATE
074 PROC LEVEL
075 RF POWER SET
076 RPT SHIFT
077 SCAN MODE
078 SCAN RESUME
079 SPLIT TONE
080 SQL/RF GAIN
081 SSB MIC GAIN
082 SSB STEP
083 TONE FREQ
084 TOT TIME
085 TUNER/ATAS
086 TX IF FILTER
087 VOX DELAY
088 VOX GAIN
089 XVTR A FREQ
090 XVTR B FREQ
091 XVTR SEL
1: Depends Mon transceiver version.
2: Depends on operating band and transceiver version.
FT-897 O M
PERATING ANUAL
Function
Sets the gain of the VOX circuitry's input level for the DIG mode.
Selects the illumination color for each operating status.
Setting of the display contrast level.
Setting of the display brightness level.
Sets up the LCD Lamp mode.
Setting of the bandwidth for the DSP CW audio filter.
Adjusts the low-cut characteristics of the DSP HPF filter.
Adjusts the high-cut characteristics of the DSP LPF filter.
Sets the DSP microphone equalization pattern.
Setting of the degree of DSP Noise Reduction.
Enables Tx/Rx operation on the Alaska Emergency Channel,
5167.5 kHz.
Adjusts the microphone gain level for the FM mode.
Selects the tuning steps for the MEM/VFO CH knob in the FM
mode.
Enables/disables the moving of HOME channel data to the VFO.
Selects the operation of the front panel's LOCK key.
Enables/disables the memory grouping feature.
Stores Alpha-Numeric "Tags" for the memory channels.
Selects the function which is engaged when you press the MEM/
VFO CH knob.
Enables/disables scanning access via the microphone's [ UP ] /
[ DWN ] keys.
The choice of the equipment which connects to the MIC jack.
Select the meter display configuration while the transceiver is
receiving.
Selects the meter display configuration while the transceiver is
transmitting.
Enabling/disabling of the "peak hold" function of the meter.
Setting of the blanking level for the IF Noise Blanker.
Not available at this time.
Programming the [A] key (in the Operating Function Row 17)
function.
Programming the [B] key (in the Operating Function Row 17)
function.
Programming the [C] key (in the Operating Function Row 17)
function.
Not available at this time.
Not available at this time.
Not available at this time.
Adjusts the audio input level from the TNC during 1200 bps Packet
operation.
Adjusts the audio input level from the TNC during 9600 bps Packet
operation.
Sets the transceiver's circuitry for the Packet baud rate to be used.
Sets the compression level for the AF speech processor in the
SSB/AM modes.
Setting of the maximum power level for the current band.
Sets the magnitude of the repeater shift.
Selects the desired Scan-Resume mode.
Sets the delay time for scanning resumption.
Enables/disables split CTCSS/DCS cording.
Selects the configuration of the front panel's SQL/RF knob.
Adjusts the microphone gain level for the SSB mode.
Selects the tuning steps for the MEM/VFO CH knob on the SSB
mode.
Setting of the CTCSS Tone Frequency.
Select the Automatic Power Off time.
Selects the device (FC-30 or ATAS-100/-120) to be controlled via
the front panel's [A](TUNE) key.
Selects the Transmit IF filter.
Sets the "hang time" for the VOX circuitry.
Sets the gain of the VOX circuitry's input audio detector.
Allows an arbitrary frequency to be set on the display, to allow
direct frequency readout during transverter operation.
Enables/disables/selects the antenna port to be used for
Transverter operation.
M O
ENU PERATION
Available Values
0 ~ 100
–
0 ~ 13
0 (Dim) ~ 3 (Bright)
OFF/AUTO1/AUTO2/ON
60/120/240 Hz
100 ~ 1000 Hz
1000 ~ 6000 Hz
OFF/LPF/HPF/BOTH
1 ~ 16
ON/OFF
0 ~ 100
5/6.25/10/12.5/15/20/25/
50 kHz
ON/OFF
DIAL/FREQ/PANEL/ALL
ON/OFF
–
CW SIDETONE, CW SPEED,
MHz/MEM GRP, MIC GAIN,
NB LEVEL, RF POWER, STEP
ON/OFF
NOR/RMT/CAT
SIG, CTR, VLT, N/A, FS, OFF SIG
PWR, ALC, MOD, SWR,
VLT, N/A, OFF
ON/OFF
0 ~ 100
–
All Multi Function , all Menu
Item, MONI, Q.SPL, TCALL,
ATC and USER.
–
–
–
0 ~ 100
0 ~ 100
1200/9600 (bps)
0 ~ 100
5 ~ 100
0.00 ~ 99.99 (MHz)
TIME/BUSY/STOP
1 ~ 10 (sec)
ON/OFF
RF-GAIN/SQL
0 ~ 100
1kHz/2.5kHz/5kHz
50 Standard CTCSS tones
OFF/1 ~ 20 (min)
OFF/ATAS(HF)/ATAS(HF&50) OFF
/ATAS(ALL)/TUNER
CFIL/FIL1/FIL2
100 ~ 3000 (ms)
1 ~ 100
00,000,00 ~ 99,999,99 (kHz)
OFF/X VTR A/X VTR B
Default
0
–
5
3
AUTO2
240 Hz
100 Hz
6000 Hz
OFF
8
OFF
50
2
ON
DIAL
OFF
–
MHz/MEM GRP
ON
NOR
PWR
ON
50
–
MONI
Q.SPL
ATC
–
–
–
50
50
1200 bps
50
100
2
TIME
5 sec
OFF
1
50
2.5 kHz
88.5 Hz
OFF
CFIL
500 ms
50
–
OFF
Page 53