ENGLISH 6-1/2" (165 mm) 18V CORDLESS CIRCULAR SAW DCS391 reduce the exposure level over the total Congratulations! working period. You have chosen a D WALT tool. Years of Identify additional safety measures to experience, thorough product development and protect the operator from the effects of...
Never modify the plug in any way. Do not use any adapter plugs with earthed CORDLESS CIRCULAR SAW (grounded) power tools. Unmodified plugs DCS391 and matching outlets will reduce risk of WALT declares that these products described electric shock. under Technical data are in compliance with: Avoid body contact with earthed or 2006/42/EC, EN 60745-1, EN 60745-2-5.
Page 8
ENGLISH use. Use of a cord suitable for outdoor use tool that cannot be controlled with the switch reduces the risk of electric shock. is dangerous and must be repaired. If operating a power tool in a damp Disconnect the plug from the power location is unavoidable, use a residual source and/or the battery pack from current device (RCD) protected supply.
ENGLISH 6) SERVICE – When the blade is pinched or bound tightly Have your power tool serviced by a by the kerf closing down, the blade stalls and qualified repair person using only identical the motor reaction drives the unit rapidly back replacement parts.
ENGLISH Safety Instructions for Saws with a WARNING: We recommend the use of a residual current device with a residual Pendulum Blade Guard current rating of 30mA or less. a) Check lower guard for proper closing before Residual Risks each use. Do not operate the saw if lower guard does not move freely and close The following risks are inherent to the use of circular instantly.
Page 11
ENGLISH CAUTION: Burn hazard. To reduce • Do not operate charger with damaged cord the risk of injury, charge only D WALT or plug — have them replaced immediately. rechargeable battery packs. Other types • Do not operate charger if it has received of batteries may overheat and burst a sharp blow, been dropped or otherwise resulting in personal injury and property...
ENGLISH Charging Process Important Safety Instructions for All Battery Packs Refer to the table below for the charge status of the battery pack. When ordering replacement battery packs, be sure to include the catalog number and voltage. Charge indicators: DCB105 The battery pack is not fully charged out of the ––...
15 minutes or until irritation ceases. If medical BATTERY TYPE attention is needed, the battery electrolyte The DCS391 operates on an 18V XR Li-Ion battery is composed of a mixture of liquid organic pack. carbonates and lithium salts.
Do not incinerate the battery pack. p. Rip guide Package Contents INTENDED USE Your DCS391 cordless circular saw has been The package contains: designed for professional wood sawing applications. 1 Cordless circular saw DO NOT use under wet conditions or in presence of 1 24-tooth blade flammable liquids or gases.
ENGLISH TO REMOVE THE BATTERY PACK FROM THE TOOL Your D WALT charger is double insulated in accordance with EN 60335; therefore 1. Press the battery release button (m) and firmly no earth wire is required. pull the battery pack out of the tool handle. If the supply cord is damaged, it must be replaced 2.
2. Insert the rip guide (p) as shown in figure 6. Prior to Operation 3. Tighten the rip guide knob (o) securely. Use the supplied rip guide only with the DCS391 • Make sure your battery pack is (fully) charged. circular saw. Use of this rip guide with other saws •...
ENGLISH WARNING: Always wear proper • Use the kerf indicator (i) to follow the line drawn personal hearing protection. Under on the workpiece. The kerf indicator lines up some conditions and duration of use, with the left side of the saw blade when set noise from this product may contribute to 50°...
ENGLISH VISUALLY EXAMINE CARBIDE BLADES BEFORE USE. REPLACE IF DAMAGED. Consult your dealer for further information on the Cleaning appropriate accessories. WARNING: Blow dirt and dust out of Protecting the Environment the main housing and the guard area with dry air as often as dirt is seen Separate collection.
Page 20
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...