Replacing The Light Bulb; Automatic Cleaning With The Fast Clean Function; Sliding Rack Kit Assembly - Hotpoint SX 1038LS P 0 X Operating Instructions Manual

Replacing the light bulb

Lamp
Holder
compartment
Lamp
Glass cover
! Do not touch the light bulb directly with your hands.
! Do not use the oven lamp as/for ambient lighting.

Sliding rack kit assembly

A
Left
Right guide
guide rail
rail
B
C
D
! Do not place the sliding racks in position 5.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
To replace the oven light bulb:
1. Remove the glass cover of the
lamp-holder.
2. Remove the light bulb and replace
it with a similar one: halogen lamp
voltage 230 V, wattage 25 W, cap G 9.
3. Replace the glass cover (see
diagram).
! ATTENTION
WHEN USING THE MAIN OVEN
YOU MUST ENSURE THAT THE
BASE OF THE CAVITY IS NOT
COVERED WITH ALUMINUM
FOIL, UTENSIL OR ANY OTHER
FORM OF COVERING. FAILURE
TO DO THIS MAY RESULT IN
THE CAVITY BEING DAMAGED.
To assemble the sliding racks:
1. Remove the two frames, lifting them
away from the spacers A (see figure).
2. Choose which shelf to use with the
sliding rack. Paying attention to the
direction in which the sliding rack is to
be extracted, position joint B and then
joint C on the frame.
3. Secure the two frames with the
guide rails using the holes provided
on the oven walls (see diagram). The
holes for the left frame are situated at
the top, while the holes for the right
frame are at the bottom.
4. Finally, fit the frames on the spacers
A.

Automatic cleaning with the FAST CLEAN function

With the FAST CLEAN mode, the internal temperature of the oven reaches
500°C. The pyrolytic cycle is activated, burning away food and grime
residues. Dirt is literally incinerated.
Keep children away from the appliance during the automatic cleaning cycle
as surfaces may become very hot. Particles may ignite inside the oven as a
result of the combustion process. There is no cause for concern: this process
is both normal and hazard-free.
Before initiating the FAST CLEAN mode:
• clean the oven door;
• remove large or coarse food residues from the inside of the oven using a
damp sponge. Do not use detergents;
• remove all accessories and the sliding rack kit (where present);
• do not place tea towels or pot holders over the oven handle.
! If the oven is too hot, the pyrolytic cycle may not start. Wait for the oven to
cool down.
! The programme may only be started once the oven door has been closed.
To activate the Fast Clean programme:
1. Switch the control panel on by pressing the
2. Press the icon; the TIME display will show the default duration of
1:30 h (normal cycle), while he TEMPERATURE display will show "Piro" and
"nor" alternately;
3. The desired cleaning level can be selected by pressing the
- pressing " " to switch to the intensive cycle: the duration is 2 h and the
TEMPERATURE display shows the text "Piro" and "int" alternately;
- pressing " " to switch to the economy cycle: the duration is 1 h and the
TEMPERATURE display shows the text "Piro" and "eco" alternately.
Safety devices
• the door locks automatically as soon as the temperature reaches a high
value; the icon lights up on the display;
• pressing the icon cancels the cleaning cycle t any time;
• if a malfunction occurs, the heating elements will be switched off;
• once the oven door has been locked, you cannot change the duration and
end time settings.
Programming delayed automatic cleaning
! Programming is possible only after selecting the FAST CLEAN mode.
1. Press the icon and set the end time using the " " and " " icons.
2. Once you have reached the desired end time, press the
3. Press the icon to activate the programmed mode.
4. When the selected time has elapsed, "END" appears on the TEMPERATURE
display and a buzzer sounds.
• For example: it is 9:00 a.m. and the Economy (ECO) FAST CLEAN level
has been selected, with the default duration of 1 hour. 12:30 is scheduled
as the end time. The programme will start automatically at 11:30 a.m.
The icons and flash to indicate that programming has taken place.
After programming, in the time before the Fast Clean mode starts, the TIME
display indicates the duration and end of the Fast Clean mode alternately.
To cancel programming press the
icon.
icon, then:
icon again.
icon.
13
GB