Error Messages - Panasonic DMR-E95H Operating Instructions Manual

Error messages

On the television
Cannot finish recording
completely.
Cannot playback this title.
TV system is different from the
setting.
To playback this title, please
change the TV System in
SETUP.
Cannot record on the disc.
Please check the disc.
Unable to format.
Cannot play on this unit.
Cannot record. Disc is full.
Cannot record. Maximum
number of titles exceeded.
Error has occurred. Please
press ENTER.
No Disc
No folders.
No PC CARD
No SD CARD
No valid PC card.
No valid SD card.
Not enough space on dubbing
destination.
Please change the disc.
This is a non-recordable disc.
This disc is not properly
formatted.
Formatting is necessary using
DISC MANAGEMENT.
$
On the unit's display
HDD SLP
HARD ERR
NO READ
PROG FULL
REMOTE DVD
("∑" stands for a number.)
SELF CHECK
U14
U99
UNSUPPORT
X HOLD
RQT7463
56
56
≥The programme was copy-protected.
≥The HDD or disc may be full.
≥You tried to play a title recorded using a different encoding system from that of the TV
system currently selected on the unit.
Alter the "TV System" setting on this unit to suit.
≥The disc may be dirty or scratched.
≥You cannot format a Microdrive or mobile hard disk on this unit.
≥You tried to play a non-compatible image.
≥Turn the unit off and re-insert the card.
≥Create space by erasing any unnecessary titles. [HDD] [RAM]
(Even if you erase recorded content from the DVD-R, there is no increase in disc space.)
≥Use a new disc.
≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering
("SELF CHECK" appears on the unit's display).
≥The disc may be upside down.
≥There is no compatible folder in this unit.
≥The card is not inserted. If this message is displayed with a compatible card already
inserted, turn off the unit, remove and then re-insert the card.
≥The card inserted is not compatible or the card format does not match.
≥Create space by erasing any unnecessary items.
≥Erase one or more items registered on the transfer (dubbing) list to ensure that the
"Destination Capacity" is not exceeded.
≥There may be a problem with the disc. Press [< OPEN/CLOSE] on the main unit to
remove it and check it for scratches or dirt. (The unit turns off automatically after you open
the tray.)
≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.
≥You inserted an unformatted DVD-RAM. Format the disc with this unit.
≥The operation is prohibited by the unit or disc.
≥In order to extend HDD life, the HDD is in SLEEP mode. Press [HDD] to activate.
≥If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥You have used a DVD-RAM/PD lens cleaner and it has finished. Press [< OPEN/CLOSE]
on the main unit to eject the disc.
≥There are already 32 timer programmes. Delete unnecessary timer programmes.
≥The remote control and main unit are using different codes. Change the code on the
remote control.
≥The unit is starting up. Wait until the message disappears.
≥The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
≥The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to standby.
Now press [Í/I] on the main unit again to turn the unit on.
≥You have inserted a disc the unit cannot play or record on.
≥The Child Lock function is activated.
Press and hold [ENTER] and [RETURN] simultaneously until "X HOLD" disappears.
Press and hold [ENTER] and the indicated number
button at the same time for more than 2 seconds.
Page
—
—
50
61
—
26
26
24, 31,
42, 43
—
—
—
15
26
15
24, 27, 31,
34, 42, 43
37
61
—
43
—
61
—
61
—
21
13
—
—
—
14
51