Waveforms; Ic Pin Function Description - Sony HCD-MC3AV Service Manual

HCD-MC3AV
Q Q

6-23. WAVEFORMS

3 7 6 3 1 5 1 5 0
– MAIN Section –
1 3
IC501 0 (X2) IC501 (¡ (CLK-OUT)
5.5Vp-p
32.768 kHz
5 MHz
2 4
IC501 !£ (XT2) IC401 #¡ (EXTAL)
32.768 kHz 4.8Vp-p 10 MHz
– MD Section –
1 5
IC101 $¡ (RFSM)TP(RF) IC102 $¢ (XOUT)X101
T E
L 1 3 9 4 2 2 9 6 5 1 3
5.2Vp-p
1.7Vp-p
16.9344 MHz
2 6
IC101 @º (FE) IC102 ^º (16M)
(PLAY MODE)
0.5Vp-p
5.3Vp-p
16.9344 MHz
7
3
IC102 ^¡ (4.2M)
IC101 7 (TE)TP(TE)
0.4Vp-p
5Vp-p
4.2336 MHz
4
IC102@¡(PCK)TP(PLCK)
5.2Vp-p
230ns
w w w
– PANEL Section –
5
IC601 8 (X-OUT)
5.0Vp-p
8MHz
4.2Vp-p
3.6Vp-p
x a o
. i
— 75 —
http://www.xiaoyu163.com

6-24. IC PIN FUNCTION DESCRIPTION

BD BOARD IC101 LA9240M (FOCUS/TRACKING/SLED SERVO, RF AMP)
Pin No. Pin Name
1 FIN2
2 FIN1
3 E
4 F
5 TB
6 TE–
7 TE
8 TESI
9 SCI
10 TH
11 TA
12 TD–
13 TD
14 JP
15 TO
16 FD
17 FD–
18 FA
19 FA–
20 FE
21 FE–
22 AGND
Q Q
23 SP
3 7 6
24 SPI
25 SPG
26 SP–
27 SPD
28 SLEQ
29 SLD
30 SL–
31 SL+
32 JP–
33 JP+
34 TGL
35 TOFF
36 TES
37 HFL
u 1 6 3
y
http://www.xiaoyu163.com
2 4
8 9 9
I/O Function
Connected to the pick-up photodiode
I
Added with FIN1 to create RF signal, subtracted with FIN1 to create FE signal
I Connected to the pick-up photodiode
I Connected to the pick-up photodiode Subtracted with F to create TE signal
I Connected to the pick-up photodiode
I DC component of the TE signal is input
I Connects the TE signal gain setting resistor between TE pins
O TE signal output
I TES (Track Error Sense) comparator input. The TE signal is band-passed and input
I Shock detection input
I Tracking gain time constant setting
O TA amplifier output
I Creates a tracking phase compensation constant between TD and VR pins
O Tracking phase compensation setting
I Tracking jump signal (kick pulse) amplitude setting
O Tracking control signal output
O Focusing control signal output
I Creates a focusing phase compensation constant between FD and FA pins
O Creates a focusing phase compensation constant between FD- and FA- pins
I Creates a focusing phase compensation constant between FA and FE pins
O FE signal output
I Connects the FE signal gain setting resistor between TE pins
— Analog signal Ground
O Single end output of CV+ and CV- pin signal
3 1 5 1 5 0 8 9
I Spindle amplifier input
I Gain setting resistor is connected when the spindle 12cm mode
I Works together with the SPD pin to connect to the spindle phase compensation constant
O Spindle control signal output
I Sled phase compensation constant is connected
O Sled control signal output
I Sled feeding signal is input from the microprocessor
I Sled feeding signal is input from the microprocessor
I Tracking jump signal is input from the DSP
I Tracking jump signal is input from the DSP
I Tracking gain control signal is input from the DSP Gain becomes low when TGL is "H"
Tracking off control signal is input from the DSP
I
Tracking becomes off when TOFF is "H"
O Outputs TES signal to the DSP
HFL (High Frequency Level) is used to determine whether the main beam is
O
positioned on a pit or a mirror
m
c o
.
— 76 —
2
8 9 9
2 4 9 8 2 9 9