Axis Q1614-E Installation Manual
Hide thumbs
Also See for Q1614-E:
- User manual (71 pages) ,
- Datasheet (4 pages) ,
- Installation manual (126 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Axis Q1614-E
Summary of Contents for Axis Q1614-E
- Page 1 AXIS Q1614-E Network Camera Installation Guide...
- Page 2 Search by product, category, or phrase Every care has been taken in the preparation of this • report problems to Axis support staff by logging in to document. Please inform your local Axis office of any your private support area inaccuracies or omissions.
- Page 3 Caused by Electronic Information Products (ACPEIP). (STP) that is properly grounded. Contact Information This product fulfills the requirements for emission and Axis Communications AB immunity according to EN 50121-4 and IEC 62236-4 railway Emdalavägen 14 applications. 223 69 Lund...
-
Page 5: Hazard Levels
AXIS Q1614-E Network Camera Safety Information Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury. -
Page 6: Safety Instructions
Battery The Axis product uses a 3.0 V CR2032 lithium battery as the power supply for its internal real-time clock (RTC). Under normal conditions this battery will last for a minimum of five years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. When the battery needs replacing, a log message will appear in the product’s server report. - Page 7 WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
-
Page 9: Installation Steps
Installation Guide This Installation Guide provides instructions for installing AXIS Q1614-E Network Camera on your network. For other aspects of using the product, see the User Manual available at www.axis.com Installation Steps 1. Make sure the package contents, tools and other materials necessary for the installation are in order. -
Page 10: Hardware Overview
AXIS Q1614-E Network Camera Hardware Overview Status LED indicator Zoom puller Focus puller... - Page 11 AXIS Q1614-E Network Camera I/O connector Iris connector Power connector* Power LED indicator Network LED indicator RS485/RS422 connector 10 Network connector (PoE) 11 Control button (1) 12 Function button (2) 13 microSD Card slot 14 Audio in 15 Audio out...
- Page 12 AXIS Q1614-E Network Camera Sunshield adjustment Sunshield Top cover Network connector (PoE IN) Safety wire tab Cable hole Network connector (PoE OUT, connected at delivery) Bottom cover screws (4x) Cable cover 10 Cable cover screws (2x) 11 Network camera 12 Bottom cover...
-
Page 13: Led Indicators
AXIS Q1614-E Network Camera 17 Wall bracket 18 Alternative cable hole LED Indicators Note • The Status LED can be configured to be unlit during normal operation. To configure, go to Setup > System Options > Ports & Devices > LED. See the online help for more information. -
Page 14: Status Led Behavior For Focus Assistant
AXIS Q1614-E Network Camera Power LED Indication Green Normal operation. Amber Flashes green/amber during firmware upgrade. Status LED Behavior for Focus Assistant Indication Color Green Focus Assistant is enabled The lens is optimally adjusted Amber The camera has been moved, or an object has been placed in front of the lens. -
Page 15: Connectors And Buttons
Double flash: Fan error Triple flash: General error Alarm events will be triggered through the camera’s input port. Contact your Axis reseller for information about spare parts and troubleshooting. Connectors and Buttons For specifications and operating conditions, see page 17. - Page 16 The control button is used for: • Resetting the product to factory default settings. See page 26. • Connecting to an AXIS Video Hosting System service or AXIS Internet Dynamic DNS Service. For more information about these services, see the User Manual.
-
Page 17: Specifications
Temperature Humidity AXIS Q1614-E -30 °C to 50 °C (-22 °F to 122 °F) with 10-100% RH (condensing) Down to -40 °C (-40 °F) with Axis High PoE midspan, max. 30 W Power Consumption Product AXIS Q1614-E Power over Ethernet IEEE 802.3af/802.3at Type 1 Class 3, max. - Page 18 AXIS Q1614-E Network Camera Function Notes Specifications 0 V DC (-) DC output Can be used to power auxiliary equipment. 12 V DC Note: This pin can only be used as power out. Max load = 50 mA 3– Configurable Digital input –...
-
Page 19: Connection Diagrams
AXIS Q1614-E Network Camera Function Notes RS485B alt RX pair for all modes (combined RX/TX for 2-wire RS485) RS485/422 RX(B) RS485A alt RS485/422 RX(A) TX pair for RS422 and 4-wire RS485 RS485/RS422 TX(B) RS485/RS422 TX(A) Important The recommended maximum cable length is 30 m (98.4 ft). -
Page 20: Install The Hardware
AXIS Q1614-E Network Camera Install the Hardware Install the Wall Mount CAUTION Make sure that the screws and plugs are appropriate for the material (e.g. wood, metal, drywall, stone) and that the material is strong enough to support the combined weight of the camera, housing, and wall mount. -
Page 21: Install The Camera On The Bracket
AXIS Q1614-E Network Camera Cable gland Gasket Plug (discard) 1. Loosen the cable cover screws; detach the cable cover from the bottom cover. 2. Remove the cap, the plug and the gasket from the cable gland. 3. Route the network cable through the cap. - Page 22 AXIS Q1614-E Network Camera Axis network camera Network cable (route through wall bracket) Cable holes Bracket screw (4x) Cable cover Cable cover screw (2x) Wall bracket Bracket adjustment screw 1. Install the camera with the bottom cover on the bracket and tighten the bracket screws.
- Page 23 AXIS Q1614-E Network Camera Connect the Cables Network cables I/O cable Bottom cover Network connector (PoE OUT, connected at delivery) Cable holes Network connector (PoE IN) LED indicator Arctic Temperature Control switch Alarm output (connected at delivery)
- Page 24 AXIS Q1614-E Network Camera 1. Optionally insert an SD memory card (not included) into the SD card slot. A standard or high capacity SD card is required to store images locally in the camera. 2. Optionally connect external input/output devices. See Connectors on page 17 for information on the connector pins.
-
Page 25: Access The Product
11. If needed, make further adjustments under the Advanced tab. See the online help for more information. Access the Product AXIS IP Utility and AXIS Camera Management are recommended methods for finding Axis products on the network and assigning them IP addresses in Windows®. Both applications are free and can be downloaded from www.axis.com/techsup... -
Page 26: Replace The Lens
• Chrome or Firefox with other operating systems. For more information about using the product, see the User Manual available at www.axis.com Replace the Lens It is possible to use optional lenses for the Axis product. To replace the lens: 1. -
Page 27: Further Information
For the latest version of this document, see www.axis.com The User Manual is available at www.axis.com Visit www.axis.com/techsup to check if there is updated firmware available for your network product. To see the currently installed firmware version, go to Setup > About. - Page 28 Installation Guide Ver. M4.8 AXIS Q1614-E Network Camera Date: July 2015 © Axis Communications AB, 2013 - 2015 Part No. 1479293...