Declaration Of Conformity; Noise/Vibration Information; Battery Charging - Bosch GST Professional 14,4 V-LI Original Instructions Manual

OBJ_BUCH-1257-004.book Page 15 Monday, October 21, 2013 10:36 AM
26 Parallel guide with circle cutter*
27 Centring tip of the circle cutter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Jigsaw GST 14,4 V-LI GST 18 V-LI
Article number 3 601 E8J 4.. 3 601 E8J 3..
Rated voltage V=
-1
Stroke rate at no load n min
0
Stroke mm
Cutting capacity, max.
– in wood mm
– in aluminium mm
– in non-alloy steel mm
Bevel cuts (left/right),
max. °
Weight according to
EPTA-Procedure
01/2003 kg
* dependent of the battery pack being used
Battery
Permitted ambient tempera-
ture
– when charging
– during operation*
– during storage
Recommended batteries
* Limited performance at temperatures <0 °C

Noise/Vibration Information

Measured sound values determined
according to EN 60745.
Typically the A-weighted noise levels
of the product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector
h
sum) and uncertainty K determined
according to EN 60745:
Cutting board:
a
h
K
Cutting sheet metal:
a
h
K
Bosch Power Tools
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
14.4 18
An estimation of the level of exposure to vibration should also
0 –2500 0 –2700
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
23 23
nificantly reduce the exposure level over the total working
period.
90 90
Identify additional safety measures to protect the operator
20 20
from the effects of vibration such as: maintain the tool and the
8 8
accessories, keep the hands warm, organisation of work pat-
terns.
45 45

Declaration of Conformity

We declare under our sole responsibility that the product de-
2.1/2.3* 2.2/2.4*
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardisation documents: EN 60745
according to the provisions of the directives 2009/125/EC
(Regulation 1194/2012), 2011/65/EU, 2004/108/EC,
2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
°C 0...+45
D-70745 Leinfelden-Echterdingen
°C –20...+50
°C –20...+60
Henk Becker
Executive Vice President
GBA 14,4V x,xAh M–.
Engineering
GBA 18V x,xAh M–.
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 24.09.2013
Assembly
 Before any work on the machine itself (e.g. mainte-
dB(A) 80 81
dB(A) 91 92
dB 3 3

Battery Charging

 Use only the battery chargers listed on the accessories
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
2
m/s 5.5 6
battery charger before using your power tool for the first time.
2
m/s 1.5 1.5
The lithium ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
2
m/s 6.5 8.5
does not damage the battery.
2
m/s 1.5 1.5
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
1 609 92A 0C6 | (21.10.13)
English | 15