Related Manuals for Honeywell 3MP
Summary of Contents for Honeywell 3MP
- Page 1 Honeywell 3MP&2MP IR Vari-Focal Bullet Camera User’s Manual Document 800-16354 Rev. A...
-
Page 3: Table Of Contents
Honeywell Contents Overview ............................ 1 Introduction ..........................1 Features ............................. 1 Minimum System Requirements ....................2 Package Contents ........................4 Connections ..........................5 Hardware Installation ........................ 7 Preparation ..........................8 Search and Set up by IPWizard II ....................8 Search ..........................8 View ............................. - Page 4 Honeywell Camera: Adjust Camera Parameters ................... 32 System: Configure and Maintain System ................38 Video: Configure OSD, Overlay, Profile, ROI and AOI ............42 Audio: Audio Parameters ....................48 User: Manage User Name, Password and Login Privilege ........... 49 Protocol: ..........................50 E-Mail: Setup E-Mail Configuration..................
- Page 5 Honeywell OWNER'S RECORD The model and serial numbers are located at the bottom of device. Record these numbers in the spaces provided below. Refer to these numbers whenever you call upon your dealer regarding this product. Model No. HICC-P-3100IRV / HICC-P-2100IRV Serial No : _ ___________________ To prevent fire or shock hazard, do not expose the unit to rain or moisture.
- Page 6 Honeywell This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s...
-
Page 7: Overview
Honeywell 1 Overview The user’s guide explains how to operate this camera from a computer. User should read this manual completely and carefully before you operate the device. Introduction This camera is an inexpensive and fully scalable surveillance device. Because the Network Cameras can be plugged into your existing local area network (LAN), you will potentially save thousands of dollars from unnecessary cabling. -
Page 8: Minimum System Requirements
Overview • UPnP device discovery and NAT router transversal for easy installation • Dynamic IP Service, DIPS®, to search your IP camera from Internet easily • H.264, MPEG4, MJPEG triple compression simultaneously • 8- or 12-profile encoder simultaneously by 3M or 2M mode •... - Page 9 Honeywell • Intel Core 2 Duo E8600(3.33GHz) or faster • Memory Size: 2GB or more • Windows XP, 7...
-
Page 10: Package Contents
Package Contents 2 Package Contents User can find the following items in the package: Item Descriptions 1. IR Network Camera is the main element of the product. 2. Switching Power Supply Convert AC/DC 24V to DC 12V for camera 3. User’s Manual CD provides installation software, application program, important information and instructions for operating the Network... -
Page 11: Connections
Honeywell 3 Connections RJ45 LAN socket: Connect to PC or Hub/Switch. It’s for connections to 10Base-T Ethernet, 100Base-TX, or 1000Base-TX Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of the network automatically. Please use Category 5 or better cable to connect the Network Camera to an Ethernet network switch or hub. - Page 12 Connections DI/ DO: Connect to sensor in and alarm out devices Cable for I/O connectors: Name Number Function 12VDC DC 12V (50mA maximum) Digital signal input Digital signal output 485+ RS485 data + 485- RS485 data - Factory Default Reset This button is used to restore the all factory default settings.
-
Page 13: Hardware Installation
Honeywell 4 Hardware Installation Fix the included stand to desired location Attach the Camera to the stand Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN socket located on the camera’s rear and attach it to the network. -
Page 14: Preparation
Preparation 5 Preparation Search and Set up by IPWizard II When you installed the Camera on a LAN environment, you have two easy ways to search your Cameras by IPWizard II or UPnP™ discovery. Here is the way to execute IPWizard II to discover Camera’s IP address and set up related parameter in a Camera. -
Page 15: View
Honeywell View If IPWizard II finds network devices, View button will be available. Please select the device you want to view and click the View button. Then you could see the video from camera directly. Furthermore you could double click the left button of mouse to link to the network... -
Page 16: Lan
Preparation In case you want to change the IP related parameters of wired interface, please select the device you want to configure and click the LAN button. Relative settings will be carried out as below. You could modify the relative settings of the selected device. Click “<<” button will quit the LAN setting procedure and click “>>”... -
Page 17: Wireless
Honeywell In case, you do not want to change username and/or password, then just click “Submit” button to perform your setting accordingly. Click “<<” button will go back to previous page. If you like to change username and/or password of the device, just click the check button. -
Page 18: Install The Device Behind A Nat Router
Preparation Click the targeted Device. Then Internet Explorer will connect to this Network Camera automatically. Install the Device behind a NAT Router Once installed, the device is accessible on your LAN. To access the device from the Internet you must configure your broadband router to allow incoming data traffic to the device. - Page 19 Honeywell Enable UPnP NAT traversal option of the Network Camera Refer to Setting Network UPnP page for detail NAT traversal setting. Note that this option is default enabled. Access your Network Camera by DIPS Refer to Setting System System page for detail DIPS information.
-
Page 20: Logging In As An User
Preparation After the ActiveX control was installed and ran, the first image will be displayed. Logging in as an User If you log in the Camera as an ordinary User, “Setting” function will be not accessible. Logging in as an Administrator If you log in the Camera as the Administrator, you can perform all the settings provided by the device. -
Page 21: Operating The Network Camera
The image shot by the device is shown here. The date and time are displayed at the top of the window. Video Profile The device supports multi-profile function for H.264, MEPG4 and MJPEG simultaneously. User can chose the proper and/or preferred profile which is listed here. 3MP: 2048x1536, 1280x960, 640x480, 320x240... -
Page 22: Streaming Protocol
Full screen live view image Show Status Bar: Show Video type, resolution and bitrate information on live view page View Size: 3MP: Adjust view size as 2048x1536, 1280x960, 640x480, 320x240 and Auto Caching: Enable and Disable Caching function 2-Way Audio The device supports 2-way audio function. -
Page 23: Full Screen
Honeywell : Disable PC audio uploading function. : Enable PC audio uploading function. Full Screen Enlarge video to full screen display. : Enlarge video to full screen display. Press “ESC” key to disable this function. PTZ Control Click to display the following control panel:... -
Page 24: Activex Control
Operating the Network Camera Choose the speed of Pan and Tilt. Preset: Add/Update the preset positions or go to one of these positions. Tour: Select one of the camera tours. Camera tour is comprised by series of preset locations. Go tour: Execute the selected camera tour. -
Page 25: Digital Zoom
Honeywell Digital Zoom Click Digital Zoom to active this function as above. User can drag or scale the box over the video to adjust zoom ratio and position. -
Page 26: Snapshot
Operating the Network Camera Snapshot Click Snapshot to activate this function. Press Snapshot button to take a picture. The image file is saved as JPEG format into your local PC. Select Browser, the pop-up window to select the save path and file name prefix, select OK to continue. If you like to retrieve the saved image, select the file to display the saved image by using any one of graph editing tools. -
Page 27: Volume
Honeywell Volume Click Volume to activate this function. There are two control bars for speaker and microphone volume respectively. Scroll these control bars to adjust the audio attribute. Check the volume mute will mute the speaker output. About Click About to show this ActiveX information. -
Page 28: Administrating The Device
Administrating the Device 7 Administrating the Device Setting This function is only available for user logged into Camera as administrator. Click on each menu name to display its setting page. Item Action Configure Network settings such as DHCP, DDNS, RTSP, Network PPPoE and UPnP Camera... - Page 29 Honeywell MAC address: Displays the Ethernet MAC address of the device. Note that user can not modify it. Obtain IP address automatically (DHCP): DHCP: Stands for Dynamic Host Configuration Protocol. Enable this checked box when a DHCP server is installed on the network to issue IP address assignment.
- Page 30 Administrating the Device If multiple devices are installed on the LAN and also required to be accessed from the WAN, then the HTTP Port can be assigned as the virtual server port mapping to support multiple devices. Click “OK” to save and enable the setting. IPv6 The IP communication protocol used for current Internet is having the problem of insufficient IP addresses.
-
Page 31: Ddns Service
Honeywell HTTPS: To enable or disable the HTTPS service here. Note that the HTTPS function of this device is not only encrypted the web content but also audio/video data. If the HTTPS is enabled, there is further option for “HTTP&HTTPS” or “HTTPS only”. In case, the “HTTPS only”... - Page 32 Administrating the Device DDNS: To enable or disable the DDNS service here. Server name: Choose one of the built-in DDNS servers. DDNS Host: The domain name is applied of this device. User name: The user name is used to log into DDNS. Password: The password is used to log into DDNS.
- Page 33 Honeywell Access the device, enter Setting Network PPPoE as below. • PPPoE: To enable or disable the PPPoE service here. User name: Type the user name for the PPPoE service which is provided by the ISP. Password: Type the password for the PPPoE service which is provided by the ISP.
- Page 34 Administrating the Device Specify the range of transmission port number of video stream. The default range is 50000 to 50999. User can specify a number between 1024 and 65535. UPnP UPnP is short for Universal Plug and Play, which is a networking architecture that provides compatibility among networking equipment, software, and peripherals.
- Page 35 Honeywell To enable or disable the UPnP service here. Friendly Name: To show the friendly name of this device here. UPnP NAT Traversal When enabled, the device will attempt to configure port mapping in a NAT router on your network, using UPnP™. Note that UPnP™ must be enabled in the NAT router first.
- Page 36 Administrating the Device IP Filter You can enter different user’s IP address which are allowing enter or denying by the device. IP Filter: To enable or disable the IP filter function here. IP Filter Policy: Choose the filter policy where is denying or allowing. IP Notification In case the IP address is changed, system is able to send out an email to alert someone if the function is enabled.
- Page 37 Honeywell TCP Notification: If enable this function, then the “TCP Server“, “TCP Port”, and “Message” fields need to be filled. TCP Server: Type the server name or the IP address of the TCP server. TCP Port: Set port number of TCP server.
-
Page 38: Camera: Adjust Camera Parameters
Administrating the Device Proxy Port: Set port number of Proxy. Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password: Type the password for the HTTP Proxy. Custom parameter: User can set specific parameters to HTTP server. Message: The message will be sent to HTTP server. - Page 39 Honeywell White Balance: Auto: will adjust the white balance automatically. Hold: will hold the white balance. Iris/Exposure Control: Change Iris and Exposure mode to fulfill different environment. Auto Iris: Controlling the coming light by exposure time and Iris. Firstly, IP cam will adjust the exposure time to reach the screen presentation, If the image is still overexposure, camera will narrow the iris to maintain correct brightness image.
- Page 40 Administrating the Device Maximum Exposure Time: Set the Maximum Exposure Time. However, the real exposure time may be shorter if good light condition. Power Frequency: Frequency of power line: 50 or 60Hz. 50Hz: Local Video out is PAL. 60Hz: Local Video out is NTSC. Exposure Value: Exposure value is AE target value.
-
Page 41: Privacy Mask
Honeywell Day Mode Threshold (0~10000): this value set the threshold to turn off IR LED. It should be higher or equal to Night Mode Threshold. Delay Time: The delay time between LED ON/OFF switching. Note that Current Value is the current luminance from the captured video. It’s a useful reference to set LED ON/OFF Threshold. -
Page 42: Ptz Setting
Administrating the Device PTZ Setting Camera Protocol: This device can connect to a PTZ camera or speed dome camera and controls them thru RS485 interface. Camera Address: This is the camera ID set in PTZ camera or speed dome camera. Note that please DO NOT change the default value if unnecessary. -
Page 43: Preset Setting
Honeywell Preset Setting This page provides the edit tool to modify or delete the “Preset Setting” item by item. Tour Setting Up to 128 positions can be preset, and the camera can be programming to move to the preset position sequentially. -
Page 44: System: Configure And Maintain System
Administrating the Device Tour Name: The group name of the sequence of camera tour. The maximum number of camera tour is Running: Enable or disable this camera tour. Sequence: Set the sequence of the tour. Maximum 16 points can be assigned. The selected preset position is added in the Sequence list from 1 to 16. - Page 45 Honeywell System Device Title: You can enter the name of this unit here. It’s very useful to identify the specific device from multiple units. The information will be shown on IPWizard II once the device is found. Software Version: This information shows the software version of the device.
- Page 46 Administrating the Device Displays the date and time of the connected PC. Adjust: Synchronize with PC: Click this option to enable time synchronization with PC time. Manual setting: Click this option to set time and date manually. Synchronize with NTP: Click this option if you want to synchronize the device’s date and time with those of time server called NTP server (Network Time Protocol).
- Page 47 Honeywell Factory Default (Except the network setting): The unit is restarted and most current settings are reset to factory default values. This action will not reset the network setting. Backup Setting: To take a backup of all of the parameters, click this button. If necessary, it will then be possible to return to the previous settings, if settings are changed and there is unexpected behavior.
-
Page 48: Video: Configure Osd, Overlay, Profile, Roi And Aoi
Video: Configure OSD, Overlay, Profile, ROI and AOI This 3MP device provides 2 modes of video profile. The first one is 3Mega mode which supports video resolution up to 3 Mega-pixel. The second one is 2Mega mode which supports video resolution up to 2 Mega-pixel. -
Page 49: Overlay Image
Honeywell User can only choose either 3Mega or 2Mega modes. 3Mega mode can serve streams up to 2048x1536 resolution maximum. On the other hand, 2 Mega mode, it can streams up to 1920x1080 resolution maximum. Text Overlay Setting: There are some important information can be embedded into image, including date, time, and/or text. - Page 50 Administrating the Device Video Profile Name: To assign a name to the selected profile. Video Type: Video codec of the selected profile. If the H.264 encoder is selected, then there are 3 modes of profile selectable: baseline, main and high profile. Resolution: Show the resolution of the selected profile.
-
Page 51: Onvif Profile
Warning!!! To enable the multicast streaming, you shall make sure your Intranet does support multicast function. Otherwise, your Intranet may occur network storm seriously. ONVIF Profile This page is 3MP device for ONVIF Profile setting, ONVIF profile1 is default streaming, when user access camera by ONVIF protocol. - Page 52 Administrating the Device Name: To assign a name to the selected profile. Video Type: Video codec of the selected profile. If the H.264 encoder is selected, then there are 3 modes of profile selectable: baseline, main and high profile. Resolution: Show the resolution of the selected profile.
- Page 53 Honeywell IP address and port for multicast video streaming of the selected profile. Multicast Audio: IP address and port for multicast audio streaming of the selected profile. Time to live: To define how many level of multicast router can be passed by multicast streaming.
-
Page 54: Audio: Audio Parameters
Administrating the Device Audio: Audio Parameters Audio: To enable or disable audio function Audio Type: To select audio codec Audio Mode: To select Simplex or Full duplex (2-way audio) mode Input Gain:... -
Page 55: User: Manage User Name, Password And Login Privilege
Honeywell To adjust gain of input audio Output Gain: To adjust gain of output audio User: Manage User Name, Password and Login Privilege Use this menu to add, update, or remove the usernames and passwords of the Administrator and viewer. -
Page 56: Protocol
Administrating the Device Protocol: ONVIF ONVIF is a global and open industry forum with the goal to facilitate the development and use of a global open standard for the interface of physical IP-based security products. Or in other words, to create a standard for how IP products within video surveillance and other physical security areas can communicate with each other. -
Page 57: E-Mail: Setup E-Mail Configuration
Honeywell SNMP Simple Network Management Protocol (SNMP) is an "Internet-standard protocol for managing devices on IP networks". Devices that typically support SNMP include routers, switches, servers, workstations, printers, modem racks and more. To enable or disable the SNMPv1 or SNMPv2c here. And set Read community and Write community. -
Page 58: Event Detection
Administrating the Device Enable: if authentication is required when an e-mail is sent. Authentication User name: Type the user name for the SMTP server if Authentication is Enable. Authentication Password: Type the password for the SMTP server if Authentication is Enable. E-mail From: Type the sender’s E-mail address. -
Page 59: Camera Tampering
Honeywell Included or Excluded Window: These windows can be specified as Included or Excluded type. Included windows target specific areas within the whole video image Excluded windows define areas within an Include window that should be ignored (areas outside Include windows are automatically ignored) Name: Name of the specified motion window. -
Page 60: Storage: Status And Configuration Of Samba Server
Administrating the Device Audio Detection Use this page to set audio as triggered source. Audio Detection: Disable and enable detection. Audio Alarm Level: Defines the sensitivity value of audio detection. The higher value will be more sensitive. Storage: Status and Configuration of SAMBA Server SAMBA Server User can setup SAMBA server related information in this page. -
Page 61: Continuous Recording
Honeywell Host: Samba server host name Share: Type the share folder of remote SAMBA server which the camera will upload files to this space User Name: Samba server user name Password: Samba server password Continuous Recording: This camera can continuously record video stream into files and save them to remote SAMBA server as possible. -
Page 62: Recording List: Files List Inside The Samba Server
Administrating the Device User can select recording to Samba server. Path: Recording File path. Restart: Restarting will delete the current recording. Oldest recordings will be removed if the dist is 90% full and free space is smaller than 1GB. Recording List: Files List inside the SAMBA server Continuous Recording List This page only shows the continuous recording files which stored in remote SAMBA server. -
Page 63: Tcp Server
Honeywell Name: User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for each FTP setting. FTP Server: Type the server name or the IP address of the FTP server. Test: Check the FTP server whether this account is available or not. -
Page 64: Http Server
Administrating the Device Name: User can specify multiple TCP servers as wish. Therefore, user needs to specify a name for each TCP server setting. TCP Server: Type the server name or the IP address of the TCP server. TCP Port: Set port number of TCP server. -
Page 65: Samba Server
Honeywell Name: User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for each HTTP server setting. URL: Type the server name or the IP address of the HTTP server. Test: Check the HTTP server whether it is available or not. -
Page 66: Event Schedule: Configure The Event Schedule
Administrating the Device Name: User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for each HTTP server setting. SAMBA Server: Type the server name or the IP address of the SAMBA server. Test: Check the SAMBA server whether this account is available or not. SAMBA Login name: Type the user name for the SAMBA server. - Page 67 Honeywell Name: Name of the Event or Schedule. Enable: Enable or disable this Event or Schedule. Type: Event trigger or Schedule trigger. Enable Time: Define the feasible time slot. Trigger by: Select the triggered sources. Record File Prefix: Define the record file prefix.
- Page 68 Administrating the Device Action: Send FTP (Add in Event Server -> FTP Server page). Example 2: Send file to E-Mail server by motion triggered always: 1. Select event trigger. 2. Enable time: start from 00:00 to 24:00 every day. 3. Trigger by: Motion Area (Added in Object Detection page). 4.
- Page 69 Honeywell Example 3: Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday. Type: Select schedule trigger and interval is 10-minute. Enable time: Select Monday to Friday, and set start time from 18:00 and keep work in 6 hours.
-
Page 70: Port Status
Administrating the Device Record File Type: Choose a profile to record. Record File Prefix: Define the prefix of recorded filename. Pre-Trigger Duration: Define the maximum duration of pre-alarm. Best Effort Duration: Define the best effort duration of post-alarm. Max File Size: Define the maximum buffer size of record file (256KByte ~ 3072KByte). - Page 71 Honeywell Input Status: Show either inactive or active. Output Status: Show either inactive or active.
-
Page 72: Appendix A: Alarm I/O Connector
Appendix A: Alarm I/O Connector 8 Appendix A: Alarm I/O Connector Some features of the Camera can be activated by the external sensor that senses physical changes in the area Camera is monitoring. These changes can include intrusion detection or certain physical change in the monitored area. For examples, the external sensor can be a door switch or an infrared motion detector. - Page 73 Honeywell Explanation of External I/O Circuit Diagram: CAUTION! • THE LOW VOLTAGE/CURRENT CIRCUITS AND HIGH VOLTAGE/ CURRENT CIRCUITS ARE IN THE NETWORK CAMERA CIRCUIT. THE QUALIFIED ELECTRICIAN SHOULD DO THE WIRING NOT BY YOURSELF. INCORRECT WIRING COULD DAMAGE NETWORK CAMERA AND YOU MIGHT RECEIVE THE FATAL ELECTRIC SHOCK.
-
Page 74: Appendix B: Troubleshooting & Frequently Asked Questions
Appendix B: Troubleshooting & Frequently Asked Questions 9 Appendix B: Troubleshooting & Frequently Asked Questions Question Answer or Resolution Features The device utilizes H.264, MPEG4, MJPEG triple compression to providing The video and audio codec is high quality images. Where H.264 is standards for video compression and MJPEG is a standard for image compression. - Page 75 Honeywell • Check the firewall setting of your PC or Notebook. Internet Explorer does not Make sure that your Internet Explorer is version 8.0 or later. If you are seem to work well with the experiencing problems, try upgrading to the latest version of Microsoft’s device Internet Explorer from the Microsoft webpage.
- Page 76 Appendix B: Troubleshooting & Frequently Asked Questions bandwidth. Go to C:\Windows\Downloaded Program Files and check to see if there is an entry for the file “IPCamera Control”. The status column should show “Installed”. If the file is not listed, make sure your Security Settings in Check the device’s ActiveX is Internet Explorer are configured properly and then try reloading the installed on your computer...
- Page 77 Honeywell 60Hz format of your device. • If the object is dark, the image will flicker. Make the condition around the Camera brighter. The video images might be noisy if the device is located in a very low light Noisy images occur.
-
Page 78: Appendix C: Ping Ip Address
Appendix C: PING IP Address 10 Appendix C: PING IP Address The PING (stands for Packet Internet Groper) command is used to detect whether a specific IP address is accessible by sending a packet to the specific address and waiting for a reply. - Page 79 Honeywell If you want to detect any other devices conflicts with the IP address of Network Camera, also can utilize the PING command but you must disconnect the Camera from the network first.
-
Page 80: Appendix D: Bandwidth Estimation
Appendix D: Bandwidth Estimation 11 Appendix D: Bandwidth Estimation The frame rate of video transmitted from the device depends on connection bandwidth between client and server, video resolution, codec type, and quality setting of server. Here is a guideline to help you roughly estimate the bandwidth requirements from your device. The required bandwidth depends on content of video source. -
Page 81: Appendix E: Specifications
Honeywell 12 Appendix E: Specifications 3MP Mode: Camera Image Device 3.4 Mega-pixel Sony Exmor image sensor Effective Pixels 2048 x 1536 pixels Image Size 1/2.8” Lens Vari-focal lens: f 3-9mm with auto Iris and ICR IP Module Video Video Encoder H.264, MPEG4 and Motion JPEG simultaneously... - Page 82 Appendix E: Specifications Camera tampering Audio detection Digital input Motion Detection 10-zone video motion detection with included or excluded options File upload via FTP, SAMBA, or email Notification via email, HTTP, and TCP Alarm Events External output activation Audio alerting output Video Buffer Pre- and post- alarm buffering General...
- Page 83 Honeywell Audio Streaming One-way or two-way Microphone External microphone input Audio Output Adjustable audio gain Network IPv4, IPv6, TCP, UDP, HTTP, HTTPS, SMTP, FTP, NTP, DNS, Supported Protocols DDNS, DHCP, DIPS, ARP, Bonjour, UPnP, RTSP, RTP, RTCP, IGMP, PPPoE, Samba, ICMP, SNMP...
-
Page 84: Appendix F: Configure Port Forwarding Manually
Appendix F: Configure Port Forwarding Manually 13 Appendix F: Configure Port Forwarding Manually The device can be used with a router. If the device wants to be accessed from the WAN, its IP address needs to be setup as fixed IP address, also the port forwarding or Virtual Server function of router needs to be setup. - Page 85 Honeywell Your WAN IP Address will be listed here Note: Because a dynamic WAN IP can change from time to time depending on your ISP, you may want to obtain a Static IP address from your ISP. A Static IP address is a fixed IP address that will not change over time and will be more convenient for you to use to access your camera from a remote location.
- Page 86 Appendix F: Configure Port Forwarding Manually Important: Some ISPs block access to port 80. Be sure to check with your ISP so that you can open the appropriate ports accordingly. If your ISP does not pass traffic on port 80, you will need to change the port the camera uses from 80 to something else, such as 8080.
-
Page 87: Appendix G: Power Line Frequency
Honeywell 14 Appendix G: Power Line Frequency COUNTRY VOLTAGE FREQUENCY COMMENTS *Neutral and line wires are reversed Argentina 220V 50 Hz from that used in Australia and elsewhere. *Outlets typically controlled by adjacent switch. Though nominal voltage has been Australia... - Page 88 Appendix G: Power Line Frequency *Outlets typically controlled by adjacent switch. Though nominal voltage has been United Kingdom 230V* 50 Hz officially changed to 230V, 240V is within tolerances and commonly found. United States of America 120V 60 Hz...
- Page 89 Email: security.ea@honeywell.com https://www.asia.security.honeywell.com India office Honeywell Security Unitech Trade Center, 5th Floor, Sector 43, Block Taiwan office C, Sushant Lok Phase - 1, Gurgaon - 122 002 10F, 168 Lien Cheng Road, Chung Ho City, Taipei, Taiwan R.O.C. Tel: (91) 124 4975000...