Sony STR-DA1200ES Service Manual page 19

SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC],
[MOVIE] button in order.
2. The message "MENU SPECIALIZED!" appears.
3. Each time the button of the remote commander is pressed, the item is switched in order as follows.
M m
4. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH], [MUSIC], [MOVIE] button in order again.
5. The message "MENU SPECIALIZED OFF" appears.
Items
Protector on/off
Model version display
Model/destination change
FM/AM tuner version display
HDMI controller version display
HDMI controller update mode
Auto cal mic test
FL display fonts test
FL display test
Audio swap
DSP halt
DSP RAM
DSP Version display
Volume value display (FL/FR)
Volume value display (SL/SR)
Volume value display (CT/SW)
Volume value display
(SBL/SBR)
DAC mute information disclosure
1
DAC mute information disclosure
2
EERROM debug
Super reset
2nd volume value display
FL display duty change
YUV Y drive
Display
PROTECTOR ON/OFF [XXX]
##### *** vX. XX @@@@
MODEL [##### * * * *] X X
FM/AM Tuner Ver X. XX
HDMI Micom Ver X. XX
HDMIUcom Update [XXX]
SPEAKER OUT [XXXXX]
FL FONT 0x ** = [X]
ALL ON
SWAP [XXXXXXXXXXX]
DSP HALT [XXX]
[*****]=XXXXXXXX
DSP Ver S: ***, P: XXX
FL**** FR XXXX
SL**** SR XXXX
CT**** SW XXXX
SBL**** SBR XXXX
DAC MUTE U XXXXXXXX
DAC MUTE L XXXXXXXX
EEPROM [****] FR XX
SUPER RESET [XXX]
2nd VOLUME XXX
DARK OUT DUTY [XXX%]
YUV Y DRIVE [XX]
XXX: ON or OFF
(switching with button of the remote commander)
M m
#####: model
***: destination
X.XX: system controller software version
@@@@: Sum value of flash memory in the main system controller
#####: model, ****: destination, XX: at or fx
(switching with button of the remote commander)
M m
X.XX: FM/AM tuner controller software version
X.XX: HDMI controller software version
XXX: ON or OFF (switching with
Reset control form the system controller side and the reset control from the
PC side interfere mutually when updating the HDMI controller and it
becomes writing NG
Therefore, when this mode is set to ON, the reset control from the system
controller side is not done
XXXXX: Selection of speaker output audio
[SOURCE]: nomally mode, [MIC]: mode that output audio from mic from
speaker
**: 20 to FE, X: character (switching with
commander)
Each time DISPLAY button to change as follows.
all on → test pattern 1 → test pattern 2 → all off → all on
Switching with button of the remote commander
M m
XXX: ON or OFF (switching with
Mode not to send DSP host code, and to make only decipherment done
Mode that refers to internal RAM of DSP (for design evaluation)
***: DSP decoder patch version
XXX: DSP post process version
****: Front L-ch volume value
XXXX: Front R-ch volume value
****: Surround L-ch volume value
XXXX: Surround R-ch volume value
****: Center volume value
XXXX: Sub woofer R-ch volume value
****: Surround back L-ch volume value
XXXX: Surround back R-ch volume value
Display of module information to demand muting in system controller (for
design evaluation)
Display of module information to demand muting in system controller (for
design evaluation)
****: EEPROM address
XX: EEPROM data (switching with
Not used for the servicing
If super reset is performed, "up convert signal level adjustment" will also be
initialized
When EEPROM initialization is required, perform the "all clear mode"
XXX: 2nd room volume value (00 to ∞)
XXX: Duty value of FL display (0% to 100%)
(switching with button of the remote commander)
M m
XX: Gain control value of brighness (00 to 1F)
(switching with button of the remote commander)
M m
STR-DA1200ES
Remark
button of the remote commander)
M m
button of the remote
M m
button of the remote commander)
M m
button of the remote commander)
M m
Ver. 1.1
19