Windows, Windows 95, 98, Me, NT, 2000, XP, Vista and Explorer are trademarks of Microsoft Corp. Apple and Mac OS are registered trademarks of Apple Inc. Other products may be trademarks or registered trademarks of their respective manufacturers. VigorTalk ATA-24 SH Series User’s Guide...
3.3.2 DDNS..........................37 3.4 Firewall Setup ........................39 3.4.1 DoS ..........................39 3.5 VoIP Setup ..........................42 3.5.1 Protocol........................... 43 3.5.2 Port Settings ........................51 3.5.3 Speed Dial ........................54 3.5.4 Dial Plan ......................... 54 VigorTalk ATA-24 SH Series User’s Guide...
Page 6
A.6 System Commands ......................101 A.6.1 General Commands ..................... 101 A.6.2 View ARP Cache Table Command ................101 A.6.3 View DHCP Assignment Command................101 A.6.4 View Routing Table Command ..................101 A.6.5 Administrator Control Commands ................101 VigorTalk ATA-24 SH Series User’s Guide...
Page 7
A.7.6 SIP Commands ......................111 A.7.7 Statistics Commands....................116 A.7.8 VoIP Status Commands ....................117 A.7.9 Tone User Defined Commands..................118 A.7.10 Config Commands...................... 119 A.7.11 List Commands ......................120 A.7.12 Protocol Commands....................120 VigorTalk ATA-24 SH Series User’s Guide...
The VigorTalk ATA-24 SH series integrates a rich suite of functions. These products are very suitable for providing multi-integrated solutions to SME markets. An application scenario for the VigorTalk ATA-24 SH is depicted in figure below, which illustrates interconnections among branch offices through the Internet via the VigorTalk ATA-24 SH adapter. Also, with Internet phone features, the company can benefit from reducing operation fees.
Page 10
It means that a normal 100 Mbps connection is through its corresponding port. It means a full duplex connection on corresponding port. It means a half duplex connection on corresponding port. VigorTalk ATA-24 SH Series User’s Guid...
Page 11
Then the adapter will restart with the factory default configuration. CONSOLE Provided for technician use. Connecter for local management. WAN (WAN1 ~ WAN2) Connecter for remote networked devices. MIRROR Connecter for security monitor. PHONE Connected to telephones. VigorTalk ATA-24 SH Series User’s Guide...
Phone service is available in VigorTalk ATA-24 SH. You can connect a RJ-11 jack port attached in a CPP to a telephone directly. The following example shows the connection for Voice transmission through CPP. Before you purchasing the device, please check your environment to determine which power type that matches with your requirement.
Users can connect the RJ-45 cable to the WAN1 port of the device. The IP address is 172.16.1.2 by default. Modify the IP address of the network segment you want to use for accessing into Internet if necessary. VigorTalk ATA-24 SH Series User’s Guide...
RJ45 cables. These cables are used on WAN, LAN, and DMZ interfaces. The VigorTalk ATA-24 SH can be mounted on a rack by using standard brackets in a 19-inch rack or optional larger brackets on 23-inch rack (not included). The bracket for 19- and 23-inch racks are shown below.
Page 15
After the bracket installation, the VigorTalk ATA-24 SH chassis can be installed in a rack by using four screws for each side of the rack. Rubber pads are included with the VigorTalk ATA-24SH. These rubber pads improve the air circulation and decrease unnecessary rubbing on the desktop.
Please type default values on the window for the first time accessing. The default value for user name is “admin” and the password is “1234”. Next, click OK. VigorTalk ATA-24 SH Series User’s Guide...
Page 18
New Password and retype it on the field of Confirm Password. Then click Apply to continue. Now, the password has been changed. Next time, use the new password to access the Web Configurator for this adapter. VigorTalk ATA-24 SH Series User’s Guid...
ISP provided. MAC Address Adapter Default- Use the default Mac address stored originally in adapter. User Definition- Use a MAC address defined by the user. VigorTalk ATA-24 SH Series User’s Guide...
Assign the downstream rate for this WAN interface. The default value is 102400 kbps (100 Megabit). This setting is very important for VigorTalk ATA-24 SH incoming buffer adjustment. If you use a DSL subscriber service with a 2Mbps downstream, please set the downstream rate setting with 2Mbps.
Page 21
Type the number for lease time. The default setting is 1440. Gateway IP Type the IP address as DHCP client. When you finished the above required settings, please click Finish. A system reboot page will appear. Click Apply to activate the static mode configuration. VigorTalk ATA-24 SH Series User’s Guide...
If you choose DHCP mode, the DHCP server of your ISP will assign a dynamic IP address for VigorTalk ATA-24 SH automatically. It is not necessary for you to assign any setting. (Host Name and Domain Name are required for some ISPs). S imply click Next to setup LAN interface.
Page 23
Type the number for lease time. The default setting is 1440. Gateway IP Type the IP address as DHCP client. When you finished the above required settings, please click Finish. A system reboot page will appear. Click Apply to activate the static mode configuration. VigorTalk ATA-24 SH Series User’s Guide...
There are four options given as shown below. No Refresh: Static information page. Every 10 Seconds: Refreshes the page every 10 seconds. Every 20 Seconds: Refreshes the page every 20 seconds. Every 30 Seconds: Refreshes the page every 30 seconds. VigorTalk ATA-24 SH Series User’s Guide...
Page 26
IP Address Displays the IP address of the LAN interface. MAC Address Displays the MAC address of the LAN Interface. RX Packets Displays the total number of received packets at the LAN interface. VigorTalk ATA-24 SH Series User’s Guid...
Typically, NTP achieves high accuracy and reliability with multiple redundant servers and diverse network paths. The VigorTalk ATA-24 SH supports synchronization with a specific NTP server or the remote PC host of the administrator. In the System group, click the Time option. The Time page is shown below: VigorTalk ATA-24 SH Series User’s Guide...
Page 28
Assign a public IP address or domain name of the NTP server. Time Zone Select the time zone where the VigorTalk ATA-24 SH is located. Daylight Savings Time Select Use to activate this function. This function is useful for some areas.
The VigorTalk ATA-24 SH supports a Syslog function to keep a record of abnormal conditions. The adapter will send Syslog packets to a Syslog server on the remote site. The administrator can observe any abnormal events from VigorTalk ATA-24. In the System group, click the Syslog option.
Disable - Disable the management from the WAN interface. the WAN Enable All - Enable all management (through HTTP/Telnet/SSH) from the WAN interface. Enable User Defined WAN IP - System can be managed by these three IP addresses via WAN. VigorTalk ATA-24 SH Series User’s Guid...
Most of the settings can be saved locally as a configuration file, and can be applied to another adapter. The VigorTalk ATA-24 SH supports the restoring and uploading functions of the configuration files. In the System group, click the Configuration Setup option. And you can see the following page.
VigorTalk ATA-24 SH allows users to upgrade firmware through a Web interface. In the System group, click the Firmware Upgrade option. You can see the following page then. Before you execute the firmware upgrade, please download the newest firmware from Draytek’s website (www.draytek.com) or FTP site (ftp.draytek.com) on the computer first.
Page 33
3. Power on VigorTalk ATA-24, then press ENTER before the system reboots completely. 4. Type LAN IP, TFTP Server IP, Image Name one by one, and press ENTER. 5. The firmware upgrade begins. 6. After firmware upgrade is finished, the device will restart. VigorTalk ATA-24 SH Series User’s Guide...
Commit can save the current settings. Please click Apply to save the VigorTalk ATA-24 SH system settings. The VigorTalk ATA-24 SH system can be restarted from a Web browser. Reboot screen can appear after you finish the changing of WAN and LAN settings. You have to reboot the adapter to invoke the configured settings that you made before.
Page 35
In some cases, a user may need to know some information about the adapter, such as static or dynamic databases, or other routing information. The VigorTalk ATA-24 SH supports four functions, Routing Table, ARP Cache Table, and DHCP Assignment Table for the user to review such information.
Page 36
Time Left Displays the remaining time for this IP address assigned by DHCP server. When the time expired, such IP address would not be kept for this client and might be assigned to other client. VigorTalk ATA-24 SH Series User’s Guid...
For Internet access, it is necessary for you to set WAN and MGN interfaces for the adapter. The VigorTalk ATA-24 SH supports two WAN interfaces (with two IP Modes – Static or DHCP), which share the same setting page. In the Network group, please click the WAN option.
Page 38
Cable modem. In most cases, you will get a DSL or cable modem from the broadband access service provider. VigorTalk ATA-24 SH is connected behind the broadband device i.e. DSL/cable modem and works as a NAT or IP adapter for broadband connections.
Page 39
Some ISP may ask you to type your domain name. Please type in if necessary. Detect Type Select a detecting type for this WAN interface. There are three ways Send ARP to Gateway, Send PING and Send HTTP VigorTalk ATA-24 SH Series User’s Guide...
Page 40
Click this button to clear all the configurations for this page. If the WAN interface is set as a DHCP client, the VigorTalk ATA-24 SH will ask for IP network settings from the DHCP server or DSL modem automatically. It is not necessary for users to manually configure the adapter.
Page 41
(sending reply to the adapter) or not. If not, the connection of WAN interface will be regarded as breaking down. This function is available when Detect Type is set with Send PING or Send Http Request. VigorTalk ATA-24 SH Series User’s Guide...
Page 42
Click Apply to go back to the WAN Interface Configuration page. To apply all settings, click Apply on the WAN Interface Configuration page and reboot your adapter. Reset Click this button to clear all the configurations for this page. VigorTalk ATA-24 SH Series User’s Guid...
Sets a lease time for the DHCP server. The time unit is minute. Gateway IP (Optional) Sets a gateway IP address for the DHCP server. Click Apply to reboot the system and apply the settings. VigorTalk ATA-24 SH Series User’s Guide...
(both TCP and UCP) of packets with these assigned port numbers are on WAN and LAN. The advantage of this feature is to filter some unnecessary packets or attacking packets on Internet environment or LAN network. VigorTalk ATA-24 SH supports ten port numbers to be blocked.
Display the activation status (disable or enable) for this entry. Status Display the connection status of this entry. Click Refresh to re-display the whole page information. To modify DDNS setting, click an entry number to get into edit mode. VigorTalk ATA-24 SH Series User’s Guide...
Page 46
Interface should be any WAN port on VigorTalk series. Server Provider Assign a provider name to support DDNS server. The VigorTalk ATA-24 SH supports 7 domain server providers as default. Server Type Select Static, Dynamic or Custom type for this entry of DDNS settings.
The firewall controls the allowance and denial of packets through the adapter. Firewall Setup in the VigorTalk ATA-24 SH Series mainly consists of Denial of Service (DoS) only. The firewall filters help to protect your computer against attack from outsiders.
Page 48
Enable Block Trace Route Activates the Block trace route function. The adapter will not forward any trace route packets. Enable Block SYN Activates the Block SYN fragment function. Any packets Fragment having the SYN flag and fragmented bit sets will be dropped. VigorTalk ATA-24 SH Series User’s Guid...
Page 49
Enable Block Unknown Activates the Block Unknown Protocol function. The adapter Protocol will block any packets with unknown protocol types. Click Apply to apply the settings when you finish the configuration. VigorTalk ATA-24 SH Series User’s Guide...
Voice over Internet Protocol (VoIP) is a technology that allows you to make telephone calls using a broadband Internet connection instead of a regular (or analog) phone line. The VigorTalk ATA-24 SH series provides cost effective voice solution for SME customers which can be explained with the following diagram.
Type the IP address or domain name of the SIP Domain/Realm. User-Agent Name Type the name for the client’s device. You can set up to 3 sets of SIP configurations in this page. For MGCP Configuration VigorTalk ATA-24 SH Series User’s Guide...
Page 52
Each endpoint sends its own RSIP – Each port must send one RSIP message (e.g., aaln/1@[172.16.3.5]) to call agent respectively. Send only one wild RSIP – Only one RSIP message (e.g., aaln/*@[172.16.3.5]) will be sent to call agent to indicate all ports are initiated/restarted. VigorTalk ATA-24 SH Series User’s Guid...
Page 53
Settings configured in Message ID field are used to be identified by the server supported with H248. H248 MessageID IP Address If you choose IPAddress:Port or IPAddress as the MessageID Mode, you have to type IP address manually in this field. VigorTalk ATA-24 SH Series User’s Guide...
Page 54
H248 Protocol. Vigor device will send the DTMF tone as audio directly when you press the keypad on the phone (Use inband signal for DTMF event). Enable –Enable the RFC2833 (outband) DTMF event for H248 VigorTalk ATA-24 SH Series User’s Guid...
Page 55
Call Forwarding Display results for call forwarding. Blank - no call forwarding. Always - call forwarding for all of the calls. Busy – call forwarding while the phone is busy. VigorTalk ATA-24 SH Series User’s Guide...
Page 56
Enter your account name of SIP Address, e.g. every text before Password The password provided to you when you registered with a SIP service. Display Name The caller-ID that you want to be displayed on your friend’s screen. VigorTalk ATA-24 SH Series User’s Guid...
Page 57
Display number only, just the number of the incoming calls will be displayed. If you choose Display name and number, then the name and number of all the incoming calls will be displayed on the phone set. VigorTalk ATA-24 SH Series User’s Guide...
Page 58
VigorTalk receives any incoming call. Ring Port Setting VigorTalk ATA-24 SH allows to connect up to 24 ring port. For such account, please specify required ring port(s) by checking the box(es) for applying the configuration.
When this port is locked, a ‘v” sign will be displayed on the page. In general, it means the connection for such port is troubled with something. When you click Edit, the following page will appear for you to configure. VigorTalk ATA-24 SH Series User’s Guide...
Page 60
Internet automatically. Codec Preferred Codec - It can be applied on this port. VigorTalk ATA-24 SH supports five Codecs. The default setting is G.729A. You can choose another one as preferred Codec for outgoing calls. VigorTalk ATA-24 SH Series User’s Guid...
Page 61
Normal: Means to enable the supplemental service with the general operation. CHT: Means to enable the supplemental service with the operation based on the requirement from CHT. Supplemental Service Items – There are thee items - Call VigorTalk ATA-24 SH Series User’s Guide...
This page allows you to set a simple way to dial a specific number. Up to 150 numbers can be stored in VigorTalk ATA-24 SH Series. Speed Dial Phone Number Type the phone number to be used as quick dial.
Page 63
Min length to match the string. Max Length Max length to match this string Prefix Strip Assign the length of digit to be removed from the original phone number. For example, suppose the original phone VigorTalk ATA-24 SH Series User’s Guide...
Congestion tone will be shown automatically on the page. If you cannot find out a suitable one, please choose User Defined and fill out the corresponding values for dial tone, ringing tone, busy tone, congestion tone by yourself for VoIP VigorTalk ATA-24 SH Series User’s Guid...
Page 65
When the time is up, the tone broadcasting will be stopped. Dial Tone – A telephony signal which indicates that the status for the telephone is off-hook. Busy Tone – A telephony signal which indicates that the calling is failed. VigorTalk ATA-24 SH Series User’s Guide...
Page 66
Congestion Tone – A telephony signal which indicates someone dials invalid call or the circuit (or network) is unable to route. Recorder Tone – The caller has connected to an automatic answering device and is requested to start speaking. VigorTalk ATA-24 SH Series User’s Guid...
It Symmetric Media is disabled, the router will transmit RTP packets via SDP ( Session Description ). The default setting is Disable Symmetric RTP Protocol and T.38. NAT Status Display current NAT status. VigorTalk ATA-24 SH Series User’s Guide...
User Phone Test – Such function must match with the subscriber. Test Item Choose one of the test types. Run Test Click this button to start the line test. VigorTalk ATA-24 SH Series User’s Guid...
Many settings that cannot be classified under VoIP are placed in this page, such as ring cadence, voice band data, MGCP port lock, offhook detect, line impedance and line PCM codec. VigorTalk ATA-24 SH Series User’s Guide...
Page 70
Timeout several seconds but not finish the complete dialing. The system will force to dial the incomplete number after the time you set in this field to finish that call. For example, the phone VigorTalk ATA-24 SH Series User’s Guid...
Page 71
Such setting determines the pulse break time for pulse digit make time phone. Keep the default setting. Minimum pulse interdigit Such setting determines the pulse break time for pulse digit time phone. Keep the default setting. VigorTalk ATA-24 SH Series User’s Guide...
Page 72
Type the duration of the next continuous ring. Toff2/Toff3/Toff4 Type the silence duration after the next continuous ring. VBD means Voice Band Data which can determine Modem or Fax or Auto mode for data transmission according to the answering tone. VigorTalk ATA-24 SH Series User’s Guid...
Page 73
Such device has the ability to detect error automatically. When something wrong happened, the system will lock all the MGCP ports. This page is available only when you choose MGCP as VoIP protocol. VigorTalk ATA-24 SH Series User’s Guide...
Page 74
Locked Ports with locked status will not be used normally. In addition, any available MGCP port can be locked at any time due to special reason if necessary. VigorTalk ATA-24 SH Series User’s Guid...
Page 75
600/900 – Available impedance value provided by the system. China, ETSI Harmonized, German Swiss, U.K, France - Such selection is available for the users in China, ETSI VigorTalk ATA-24 SH Series User’s Guide...
Page 76
One by One When you click such item, you have to specify which ring port will be applied with the configuration set here. If you choose multiple ports, they will apply the configuration one by one. VigorTalk ATA-24 SH Series User’s Guid...
Page 77
H248 Client will reply the RTP termination ID to the call agent while it tries to create a call. The <digit> part of RTP termination ID is increased with one for each call. Start Number Set the start number of digit string. VigorTalk ATA-24 SH Series User’s Guide...
Allow all incoming calls – All incoming calls from remote ends are accepted by this adapter. Allow only calls from allow list – Only the calls listed in the Allow List page will be accepted by this adapter. VigorTalk ATA-24 SH Series User’s Guid...
Page 79
Otherwise, use the static IP address or DDNS domain name. The VigorTalk ATA-24 SH supports up to 30 entries in the Deny List table. When you choose Deny only calls from deny list as the Barring Class, people listed in this list cannot call this adapter.
Page 80
The IP address or domain name to be denied. If the peer is registered in SIP proxy server, use the domain name of the SIP proxy server. Otherwise, use the static IP address or DDNS domain name. VigorTalk ATA-24 SH Series User’s Guid...
Use the drop down list of Refresh Option to choose an automatic refreshing setting. If you choose No Refresh, the system will not refresh this page until you click Refresh button. This page displays statistics for RTP. VigorTalk ATA-24 SH Series User’s Guide...
Page 82
This page is used to set RTP threshold settings for alert message. The alert message will be sent out when the values of the incoming phone calls beyond the settings configured in this page. In addition, the alert message will be displayed on the page of Show Alert. VigorTalk ATA-24 SH Series User’s Guid...
RTCP Timeout Set the value (default setting is 10) for RTP timeout setting. This feature displays Port and SIP status for VoIP phone calls. This page displays the connection status for VoIP phone calls. VigorTalk ATA-24 SH Series User’s Guide...
Page 84
JI means inter arrival jitter estimates (unit is ms). Codec Type The Codec mode used for this phone calling. Packet Period The period of time for sampling on voice signal. The status of VAD. DTMF Relay The status of DTMF. VigorTalk ATA-24 SH Series User’s Guid...
Page 85
Use the drop down list of Refresh Option to choose an automatic refreshing setting. If you choose No Refresh, the system will not refresh this page until you click Refresh button. VigorTalk ATA-24 SH Series User’s Guide...
Page 86
Use the drop down list of Refresh Option to choose an automatic refreshing setting. If you choose No Refresh, the system will not refresh this page until you click Refresh button. VigorTalk ATA-24 SH Series User’s Guid...
The status of DTMF. This page will activate the new configured settings. Click Apply to execute the new settings. When the VoIP settings are configured, it must be activated after clicking Apply in this page. VigorTalk ATA-24 SH Series User’s Guid...
Check if the power line and WLAN/MGN cable connections is OK. If not, refer to “2.1 Hardware Installation” for reconnection. Turn on the adapter. Make sure the ACT LED blinks once per second and the correspondent WAN/MGN LED is bright. VigorTalk ATA-24 SH Series User’s Guide...
Page 90
The example is based on Windows XP. As to the examples for other operation systems, please refer to the similar steps or find support notes in www.draytek.com. Go to Control Panel and then double-click on Network Connections. Right-click on Local Area Connection and click on Properties. VigorTalk ATA-24 SH Series User’s Guid...
Page 91
Select Internet Protocol (TCP/IP) and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically. VigorTalk ATA-24 SH Series User’s Guide...
Page 92
1. Double click on the current used MacOs on the desktop. 2. Open the Application folder and get into Network. 3. On the Network screen, select Using DHCP from the drop down list of Configure IPv4. VigorTalk ATA-24 SH Series User’s Guid...
Open the Application folder and get into Utilities. Double click Terminal. The Terminal window will appear. Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of 64 bytes from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms will appear. VigorTalk ATA-24 SH Series User’s Guide...
Page 94
If anything wrong, please retype correct values and try the network connection again. After finishing the settings, go to System - Status page and click WAN Status. You will get a correct web page of WAN settings. VigorTalk ATA-24 SH Series User’s Guid...
Page 95
If anything wrong, please check and retype correct values. Then try the network connection again. After finishing the settings, go to System - Status page and click WAN Status. You will get a correct web page of WAN settings. VigorTalk ATA-24 SH Series User’s Guide...
5 seconds. Then, the adapter will restart with the default configuration. After restore the factory default setting, you can configure the settings for the adapter again to fit your personal request. VigorTalk ATA-24 SH Series User’s Guid...
Page 97
ISP technical support representative to help you for configuration. Also, if the adapter still cannot work correctly, please contact your dealer for help. For any further questions, please send e-mail to support@draytek.com. VigorTalk ATA-24 SH Series User’s Guide...
Page 98
This page is left blank. VigorTalk ATA-24 SH Series User’s Guid...
The PC should be the same subnet as ATA-24 VoIP Board. The default IP address is 192.168.1.1. The default login name is “admin”, password is “1234”. - Enter advanced configuration function ATA24-SH> advance - Enter system diagnostics function ATA24-SH> diag - Enter firewall configuration function ATA24-SH> firewall VigorTalk ATA-24 SH Series User’s Guide...
- Set the synflood detection function ATA24-SH/ firewall >dos/ synflood - Set the udpflood detection function ATA24-SH/ firewall >dos/ udpflood - Enable Dos Command ATA24-SH/ firewall >dos/enable - Help ATA24-SH/ firewall >dos >icmpflood ? - Icmpflood commands usage VigorTalk ATA-24 SH Series User’s Guid...
Page 103
<Value> 0-65535, default=300 packets/sec - Help ATA24-SH/network>dos >synflood ? - Portscan commands usage ATA24-SH/firewall/dos/synflood >enable <Option> ATA24-SH/firewall/dos/synflood >threshold <Value> <Option> 0: disable SynFlood detection function 1: enable SynFlood detection function 0-65535, default=300 packets/sec <Value> VigorTalk ATA-24 SH Series User’s Guide...
- Set the dhcp mode ATA24-SH/network/ mgn > dhcp - Set the IP address ATA24-SH/network/ mgn > ip - Set the Mac Address Manually ATA24-SH/network/ mgn > mac - Help ATA24-SH/network/ mgn >dhcp ? VigorTalk ATA-24 SH Series User’s Guid...
- Edit IP_NAT setting ATA24-SH/network/ mgn >ip –w <IP> <Netmask> <IP> IP address. <Netmask> Subnet mask for NAT. - Help ATA24-SH/network/mgn>mac ? - Display IP route setting ATA24-SH/network/mgn>mac 1 <Mac Address> < Mac Address > xx:xx:xx:xx:xx:xx VigorTalk ATA-24 SH Series User’s Guide...
Page 106
- Display current setting ATA24-SH/network/wan>dhcp -s <index> - Edit WAN setting ATA24-SH/network/wan>dhcp <index> ATA24-SH/network/wan>dhcp <index> <hostname> <domainname> <index> 1: WAN1 2: WAN2 < hostname > Name of the host. < domainname > Name of the domain VigorTalk ATA-24 SH Series User’s Guid...
Page 107
- Display all WAN interfaces settings ATA24-SH/network/wan> show - Display specified WAN interface settings ATA24-SH/network/wan>show <index> <index> 1: WAN1 2: WAN2 <index> 1: WAN1 2: WAN2 - Help ATA24-SH/network/wan>speed ? - Display current setting VigorTalk ATA-24 SH Series User’s Guide...
Page 108
<No-Reply Count> Assign a number (times) to ensure the connection of the WAN is on. After passing the times you set in this field and no reply received by the adapter, the connection of WAN VigorTalk ATA-24 SH Series User’s Guid...
- Edit password for administrator ATA24-SH/system>administrator<old password> <new password> <verify password> Type old password. <old password> <new password> Type new password. <verify password> Retype the password for verification. - Help ATA24-SH/system > auto_logout ? VigorTalk ATA-24 SH Series User’s Guide...
ATA24-SH/system> manage_port -e <HTTP Enable> <TELNET Enable> - Change port number for HTTP/Telnet function ATA24-SH/system> manage_port -p <Http> <Telnet> - Set IP address for the connection through WAN interface ATA24-SH/system> manage_port -i <index> <IP Start> <IP End> VigorTalk ATA-24 SH Series User’s Guid...
1: local use 1 (local1) 2: local use 2 (local2) 3: local use 3 (local3) 4: local use 4 (local4) 5: local use 5 (local5) 6: local use 6 (local6) 7: local use 7 (local7) VigorTalk ATA-24 SH Series User’s Guide...
- Display the setting ATA24-SH/system> upgrade -s - Execute the firmware upgrade ATA24-SH/system> upgrade <File Name> <Server IP> <File Name> Octets string maximum length is 64. <Server IP> Type IP address for the ATA-24 SH. VigorTalk ATA-24 SH Series User’s Guid...
ATA24-SH/voip/h248>termId <Termination> <ID> <IPAddress> Domain name or IP Address <Port> 1 to 65535 <Termination> 1 to 24 <Timer> 0: short timer 1: long timer <Sec> 1 to 99 (sec) <Mode> 0: [IPAddress]:Port 1: [IPAddress] VigorTalk ATA-24 SH Series User’s Guide...
- Edit the style mode for end point ATA24-SH/voip/mgcp> epidstyle -m<Mode> - Edit the logic ID for end point ATA24-SH/voip/mgcp> epidstyle -l <LogicID> - Edit the domain name for end point ATA24-SH/voip/mgcp> epidstyle -d <DomainName> VigorTalk ATA-24 SH Series User’s Guid...
Page 115
0: Disable 1: Enable (default=0) There are two options for users to select. Each endpoint sends its own RSIP Send only one wild-carded RSIP “Enable” to activate this function. “Disable” to close this function. (Default is Disable) VigorTalk ATA-24 SH Series User’s Guide...
- Set same value for each line ATA24-SH/voip/misc> linepcmcodec <codec> ATA24-SH/voip/misc> linepcmcodec <line> c - Display metering parameter ATA24-SH/voip/misc> metering –s - Set metering parameter ATA24-SH/voip/misc> metering ATA24-SH/voip/misc> metering -r <Reversal as Callee off-hook> <Reversal as Callee on-hook> VigorTalk ATA-24 SH Series User’s Guid...
Page 117
- Display Voice Band Data (VBD) Configuration ATA24-SH/voip/misc> vbd -s - Set Voice Band Data (VBD) (same value for each line) ATA24-SH/voip/misc> vbd <VBD> - Set Voice Band Data (VBD) ATA24-SH/voip/misc> vbd <port><VBD> <value> Range: 1~60 (second) <enable> 0: disable VigorTalk ATA-24 SH Series User’s Guide...
Page 118
20: 20 HZ (default) 25: 25 HZ Pattern Index, Index Value: 1-8 <Index> <Ton1> Ton1 of cadence, unit: (ms) <Toff1> Toff1 of cadence, unit: (ms) <Ton2> Ton2 of cadence, unit: (ms) <Toff2> Toff2 of cadence, unit: (ms) VigorTalk ATA-24 SH Series User’s Guid...
ATA24-SH/voip/misc> deny -s <Index> - Edit deny list of incoming calls (for SIP) ATA24-SH/voip/sip> deny -e <Index> <Name> <IP/Domain> - Delete deny list of incoming calls (for SIP) ATA24-SH/voip/sip> deny -d <Index> ATA24-SH/voip/sip> deny –d VigorTalk ATA-24 SH Series User’s Guide...
Page 120
- Edit DTMF relay mode and SIP INFO mode for the port# ATA24-SH/voip/sip>dtmf_relay <Port> <Mode> <SipInfoMode> ATA24-SH/voip/sip>dtmf_relay -gain <port> <Gain Value> - Display fax transporting setting ATA24-SH/voip/sip> fax -s - Edit fax mode for the port# ATA24-SH/voip/sip> fax <Port> <Mode> VigorTalk ATA-24 SH Series User’s Guid...
Page 121
ATA24-SH/voip/sip> sipua -e ATA24-SH/voip/sip>dialplan -D - Display speed dial setting ATA24-SH/voip/sip> speeddial –s ATA24-SH/voip/sip> speeddial -s <start> <end> - Add speed dial number and destination for the entry ATA24-SH/voip/sip> speeddial –a <Number> <Destination> <Memo> VigorTalk ATA-24 SH Series User’s Guide...
Page 122
“Disable” to stop using VAD. (Default is Disable) <Active> “Enable” to activate this port. “Disable” to close this port. (Default is Disable) <SIP Account> 1 to 32 1 to 60 <EntryIdx> <MatchString> Matched string, ex: 9011x.T, maximum 63 VigorTalk ATA-24 SH Series User’s Guid...
Page 123
Assign an IP address of SIP proxy server. (Default is 0) < ProxyPort > Assign a port number of SIP proxy server. 1…65535 (Default is 5060) < RegistrarIP > Assign an IP address or domain name of SIP VigorTalk ATA-24 SH Series User’s Guide...
<Destination> Assign an address of dialing destination. Ex: 101@iptel.org - Help in the Statistics function ATA24-SH/voip/Statistics > ? - Display call statistics setting ATA24-SH/voip/statistics> callstat - Display the setting by port ATA24-SH/voip/statistics> callstat <Port> VigorTalk ATA-24 SH Series User’s Guid...
The silence duration after the next continuous ringing. (10msec per unit) (Default is 0) <Type> 0: North America for call ID setting 1: JAPAN 2: ETSI (Default is 2) 3: DTMF - Help in the Statistics function ATA24-SH/voip/status> ? VigorTalk ATA-24 SH Series User’s Guide...
ATA24-SH/voip/tone/user_defined> dial <Lowfreq> <Highfreq> <Ton1> <Toff1> <Ton2> <Toff2> - Display user defined ringing tone setting ATA24-SH/voip/tone/user_defined> ringing -s - Edit frequency and cadence for ringing tone ATA24-SH/voip/tone/user_defined> ringing <Lowfreq> <Highfreq> <Ton1> <Toff1> <Ton2> <Toff2> VigorTalk ATA-24 SH Series User’s Guid...
CPT tone timer setting 2: Busy Tone 3: Howler Tone 4: Ringing Tone 5: Special Dial Tone 6: Call waiting Tone 7: Congestion Tone 8: Reorder Tone <Timer> Range: 0~300 <sec> - Help ATA24-SH/voip>protocol ? VigorTalk ATA-24 SH Series User’s Guide...
- Help ATA24-SH/voip>listcmds ? - Display all VoIP CLI commands ATA24-SH/voip>listcmds - Help ATA24-SH/voip>protocol ? - Display the setting ATA24-SH/voip>protocol -s - Set the voip protocol ATA24-SH/voip>protocol <Protocol> <Protocol> 0: MGCP, 1: SIP, 2:H.248 VigorTalk ATA-24 SH Series User’s Guid...