Troubleshooting - Casio QV-770 Owner's Manual

5.
Use [+] and [–] to select
SEND, and then press
the shutter button.
6.
Use [+] and [–] to select ALL, and then press
the shutter button.
7.
Use step 6 of the proce-
d u r e u n d e r "
BUTTON OPERATION"
on page 67 to start the
data transfer operation.

TROUBLESHOOTING

Symptom Probable Cause
No power 1. Batteries not loaded correctly.
2. Dead batteries
3. Wrong AC adaptor
Sudden power failure 1. Operation of Auto Power Off
2. Low battery power
3. Use of manganese batteries.
indicator on LCD Batteries are about to go dead.
No recording when shutter 1. Function Switch sets to PLAY.
button is pressed 2. Flash unit is charging.
3. The message "MEMORY FULL" is on the monitor
screen.
4. The message "REMAINING" is on the monitor
screen.
Power failure during self- Low battery power
timer operation
Poor LCD image focus Incorrect NORMAL/MACRO switch setting
Poor color and brightness Indoor fluorescent lighting
when indoors
INFRARED DATA TRANSFER
Transferring Images Using PC Link Software
With PC Link Software, Cable-free infrared image data
transfer can be performed with a personal computer that
supports IrDA1.0 protocol or later. See the documentation
that comes with your computer for details on its infrared
communication capabilities.
1.
Slide the Function Switch to the PLAY posi-
tion.
2.
Press MENU.
3.
Use [+] and [–] to select
IR, and then press the
shutter button.
Action
1. Correctly load batteries (page 16).
2. Replace batteries with new ones (page 16).
3. Use only recommended AC adaptor .
1. Turn power back on.
2. Replace batteries with new ones (page 16).
3. Replace manganese batteries with alkaline bat-
teries.
Replace all four batteries with a set of new ones
(page 16).
1. Set Function Switch to REC.
2. Wait until flash unit charging is finished.
3. Delete images you no longer need from camera
memory.
4. Press to change to another resolution
mode, or delete images you no longer need from
camera memory.
Replace batteries (page 16).
Use NORMAL for scenery and group photos, and
MACRO for close-ups (page 24).
Shoot under incandescent or other non-fluorescent
lighting (page 21).
INFRARED DATA TRANSFER
4.
Use [+] and [–] to select
QV-LINK, and then press
the shutter button.
5.
Align the infrared port of the camera with the
port of your computer.
6.
Start up the PC Link software on your com-
puter and transfer the images you want.
69 70
TROUBLESHOOTING
Symptom
Cannot perform movie re- 1. Movie Record Mode is not selected.
cording.
2. Insufficient camera memory capacity.
Color of recorded image is Reflection from sunlight or light from another
strange. source
No +/– button operation Button operation during page change
during multi-page display
Camera is connected to a 1. Incorrect camera-TV connection
TV, but LCD monitor con-
tents do not appear on TV 2. Wrong TV set up
screen.
Delete operation does not All pages are protected.
operate.
Menu icon is blue and noth- Icons for functions that are disabled in the Playback
ing happens when it is se- Mode are blue.
lected.
All buttons and switches do Malfunction due to static electrical charge or strong
not operate. impact.
Camera is connected to a computer or QV Color
Printer.
71 72
Infrared Data Transfer Precautions
• Make sure that the infrared ports of the sending unit and
the receiving unit are pointed straight at each other, and
that there is nothing blocking the path between them.
• To avoid problems that occur due to sudden loss of battery
power during infrared image transfer, we recommend that
you use the separately AC adaptor specified for this cam-
era when transferring images.
• This camera cannot perform infrared data transfer with any
device that does not support the IrTran-P protocol.
• Avoid performing infrared data transfers in areas expose to
direct sunlight or other strong illumination.
• Such conditions as natural outdoor light, low battery power,
too much distance between infrared ports, and misalign-
ment of infrared ports can cause failure of image transfers
or corrupted data.
• Proper image data transfer is impossible whenever there is
anything blocking either of the infrared ports.
• Do not locate any other infrared emitting device (such as
remote control units) or fluorescent lighting in the vicinity of
the cameras while they are performing infrared image
transfers.
• A sender ID, which shows manufacturer and model name,
normally appears on the display during infrared data com-
munication. Some equipment, however, does not transmit
a sender ID, in which case nothing appears on the display.
• Failure to be able to establish an IrDA connection can
mean that the device you are trying to communication with
does not support the IrDA standard, or that the applications
being used are not compatible. When this happens, you
probably have to connect the camera to the computer with
a separately available cable for data transfer.
Probable Cause Action
1. Press MODE to enter the Movie Record Mode
(page 27).
2. Delete images you no longer need from camera
memory, so there are at least two images worth
of free memory capacity (page 54).
Reorient the camera so that light is not shining di-
rectly into lens.
Wait until an image is on the LCD before performing
a button operation.
1. Connect correctly using the special video cable
that comes with the camera (page 60).
2. Set up the TV correctly.
Unprotect the page you want to delete (page 51).
Select a different function or change to the Record
Mode.
Remove batteries and disconnect the AC adaptor if
you are using one. Restore power and turn the
camera on. If this does not work, contact your
dealer or an authorized CASIO service provider.