Entering Letters/Characters; Specifications; Questions And Answers - Gigaset A400 User Manual

Appendix

Entering letters/characters

Press the relevant key the number of times indicated.
Briefly press the hash key
"123" mode, from "123" to "abc" mode and from "abc"
to "Abc" mode.
Standard characters
1x 2x 3x 4x 5x 6x 7x 8x 9x 10 11 12 13 14 15
1 1 £ $ ¥ ¤
2 a b c 2 ä á à â ã ç
I d e f 3 ë é è ê
4 g h i 4 ï
í
5 j k l 5
L m n o 6 ö ñ ó ò ô õ
M p q r s 7 ß
N t u v 8 ü ú ù û
O w x y z 9 ÿ ý æ ø å
Q
1)
. , ? ! 0 + -
P
* / ( ) < = > %
#
Abc
123 # @ \ & §
-->
-->
123 abc
1) Space

Specifications

Recommended batteries
Technology: Nickel-metal-hydride (NiMH)
Size: AAA (Micro, HR03)
Voltage: 1.2 V
Capacity: 400–800 mAh
The device is supplied with two approved batteries.
Base power consumption
In standby mode
- Charged handset in base
- Handset not in base
During a call
General specifications
DECT standard Is supported
GAP standard Is supported
(The Gigaset handset is only fully
functional on Gigaset bases)
Range Up to 300 m outdoors
Up to 50 m indoors
Base power supply 230 V ~/50 Hz
Environmental condi- +5°C to +45°C, 20% to 75% relative
tions in operation humidity
Standbytime 220 hours
Talktime 20 hours
Operating time for 1.5
hours of calls per day
Without Eco Mode+ 135 hours
With Eco Mode+ 90 hours
Charging time in
charger 5.5 hours
#
to switch from "Abc" to
ì î
: ¿ ¡ " ' ; _
approx. 0.7 W
< 0.4 W
approx. 0.5 W
12

Questions and answers

If you have any queries about the use of your tele-
phone, visit our website at
www.gigaset.com/service
for assistance 24/7. The table below contains a list of
common problems and possible solutions.
Problem Cause
Nothing The handset is not
appears in the switched on.
display.
The batteries are
flat.
No wireless The handset is out-
connection to side the range of
the base, Base the base.
flashes in the The handset is not
display. registered.
The base is not
switched on.
You cannot The phone cord
hear a ringer supplied has not
melody/dial- been used or has
ling tone from been replaced by a
the fixed line new cord with the
network. wrong pin connec-
tions.
Error tone You have entered
sounds after the wrong system
system PIN PIN.
prompt.
PIN forgotten.
The connec- Repeater acti-
tion always vated/deactivated
¢ page 11.
terminates
after approx.
30 seconds.
Solution
a Press the end call key
for approx.
5 seconds or place the
handset in the base.
Charge or replace the
batteries.
Move the handset
closer to the base.
Register the handset
¢ page 9.
Check the mains con-
nector on the base
¢ page 3.
Please always use the
phone cord supplied or
ensure that the pin
connections are cor-
rect when purchasing
from a retailer: 3-4
assignment of tele-
phone leads/EURO
CTR37.
Reset the system PIN to
the default setting
0000 ¢ page 11.
All handsets are de-
registered. All settings
are reset. All lists are
deleted.
Deactivate and
reactivate the handset
¢ page 6.