http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 • Design and specifications are subject to change without notice L 13942296513 u163 http://www.xiaoyu163.com...
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the CAUTION 3 7 63 1515 0 instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous WARNING! radiation exposure.
http://www.xiaoyu163.com WIRING-2 (VCD/FRONT) 3 7 6 3 1 5 1 5 0 FRONT C. B (COMPONENT SIDE) VCD C. B (COMPONENT SIDE) R536 C503 JR211 R537 IC303 IC302 R546 R545 JR212 R379 C512 C288 C372 C287 C291 R291 R287 C286 C295 R284 R285...
Page 11
http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 FRONT C. B TO/FROM MAIN C. B CN601 (CONDUCTOR SIDE) S101 (OPEN / CLOSE) VCD C. B (CONDUCTOR SIDE) REPEAT J301 VIDEO R294 R296 C303 R293 J301 Q301 C302 R304 R398 R203 R224...
http://www.xiaoyu163.com IC DESCRIPTION IC, CXA1992AR 3 7 63 1515 0 Pin No. Pin Name Description Output terminal for focus error amplifier. Internally connected to window comparator input for bias condition. Input terminal for focus error. FDFCT Capacitor connection terminal for time constant used when there is defect. This pin is connected to GND via capacitor when high frequency gain of the focus servo is attenuated.
Page 19
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description RF_I Input terminal by capacity combination of RF summing amplifier. RF_O Output terminal of RF summing amplifier. Checkpoint of Eye pattern. Anti-reverse input terminal for RF summing amplifier. RF_M The gain of RF amplifier is decided by the connection resistance between RF_M and RFO terminals.
Page 20
http://www.xiaoyu163.com IC, CXD2540Q 3 7 63 1515 0 Pin No. Pin Name Description Focus OK input. Used for SENS output and the servo auto sequencer. Spindle motor output filter switching output. Spindle motor on/off control output. Spindle motor servo control. High, when sampled value of GFS at 460Hz is high.
Page 21
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description DA11 DA11 output when PSSL=1. GTOP output when PSSL=0. DA10 DA10 output when PSSL=1. XUGF output when PSSL=0. DA09 DA09 output when PSSL=1. XPLCK output when PSSL=0. DA08 DA08 output when PSSL=1. GFS output when PSSL=0. DA07 DA07 output when PSSL=1.
Page 22
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description DATO Serial data output to SSP. XLTO Serial data latch output to SSP. Latched at the falling edge. CLKO Serial data transfer clock output to SSP. Mirror signal input. Used when the number of tracks is 128 or more for the 2N-track MIRR jump and M track move of the auto sequencer.
Page 23
http://www.xiaoyu163.com IC, CL680-D1 3 7 63 1515 0 Pin No. Pin Name Description — No connection. — GND. CD BCK Bit clock input from CD DSP. CD DATA Data input from CD DSP. CD LRCK LRCK input from CD DSP. CD C2PO C2 pointer input from CD DSP.
Page 24
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description Y OUT Video signal “Y” OUT. AVDD DAC — Analog power supply (DAC) 3.3V. AGND DAC — Analog ground. R REF Reference resistor input. V REF Voltage reference input. AVDD DAC —...
Page 25
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description __________ HINT Micon interface. (Host interrupt) CDG SCK CD-G serial clock input. — Ground. Micon interface. (Host clock) VDD3 — Power supply 3.3V. HD IN Micon interface. (Host data in) VDD3 —...
Page 26
http://www.xiaoyu163.com IC, LC867248A-5H31 3 7 63 1515 0 Pin No. Pin Name Description O-SCONTM M62439SP control. open drain output. O-SCONTL O-TUDI Tuner control. CMOS output. I-TUDO Tuner control. O-TUCL Tuner control. CMOS output. O-COIN CD control. open drain output. I-SQOUT CD control.
Page 28
http://www.xiaoyu163.com IC, SM5878AN 3 7 63 1515 0 Pin No. Pin Name Description MODE = H: Soft mute ON/OFF terminal. (Mute at H). MUTE MODE = L: Attenuator level DOWN/UP terminal. (DOWN at H). DEEM De-emphasis ON/OFF terminal. (De-emphasis ON at H). Oscillator clock output.
Page 29
http://www.xiaoyu163.com IC, LC74781M-9017 3 7 63 1515 0 Pin No. Pin Name Description VSS1 — GND connection terminal. (Digital ground terminal). Xtal IN External X’tal and capacitor for internal sync generator, or the external clock are Xtal OUT connected to this terminal. (2fsc or 4fsc). Either the external clock input mode or the X’tal generator mode is selected by this CTRL1 selector terminal.
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description ______________ Controls whether or not to input the VSYNC signal to the SEPIN input. L: to input the CTRL3 ______________ ______________ VSYNC signal. H: not to input the VSYNC signal. ________ System reset input terminal.
http://www.xiaoyu163.com CD MECHANISM EXPLODED VIEW 1/1 3 7 63 1515 0 COVER SPINDLE MOTOR SPINDLE MOTOR L 13942296513 (M1) (M3) MOTOR C.B MOTOR-1 C.B CD MECHANISM PARTS LIST 1/1 REF. NO PART NO. KANRI DESCRIPTION 1 9X-262-587-010 MOTOR CHASSIS ASSY 2 92-626-907-010 GEAR(A) 6 98-848-376-110...