Table of Contents
Advertisement
Quick Links
User's Manual
for Cordless Answering
System Telephone 7610
Fold open this manual for information about this
telephone's installation and operation. Please
read Part 1 – Important Product Information,
included in this package
Part 2
© Copyright 1997 Lucent Technologies, Inc. All rights reserved.
Printed in Mexico. Issue L4
847868304
Advertisement
Table of Contents
Related Manuals for AT&T 847868304
Summary of Contents for AT&T 847868304
- Page 1 Fold open this manual for information about this telephone's installation and operation. Please read Part 1 – Important Product Information, included in this package Part 2 © Copyright 1997 Lucent Technologies, Inc. All rights reserved. Printed in Mexico. Issue L4 847868304...
-
Page 2: Installation
I N S T A L L A T I O N Standard AC Outlet AC Adapter Power Cord Insert the microcassette. Lift the cover and insert the microcassette with the full reel to the right. Choose a spot near an electrical outlet and a telephone jack. - Page 3 I N S T A L L A T I O N Fast forward during message playback. Save messages. should be on steady. If the light is flashing rapidly, the microcassette is not installed properly. Remove the cassette, and check to see if it's damaged.
-
Page 4: Charging The Handset Battery Pack
Charging the Handset Battery Pack The batteries need charging when: • The phone beeps four times when you press P. • The LOW BATTERY light on the handset flashes on and off. • The phone does not respond when you press P, and no lights go on. -
Page 5: In Case Of Difficulty
I N C A S E O F D I F F I C U L T Y If you have difficulty operating this phone, try the suggestions below. If you still have trouble, call Lucent Technologies at 1 800 222-3111. If the phone does not work at all, check these items first •... - Page 6 I N C A S E O F D I F F I C U L T Y If you have difficulty hearing messages • If messages are garbled, the recording heads may be soiled and should be cleaned. • Unplug the system from the electrical outlet.
-
Page 7: Operation
O P E R A T I O N Making A Call Press P, and wait for the PHONE light to go on steadily. When you hear a dial tone, dial the number. NOTE: You might experience a slight de- lay before you hear a dial tone, as the AutoSelect ®... -
Page 8: Storing Numbers Just Dialed
Light goes on when battery needs recharging Mute handset microphone. Redial last number called. Access telephone subscriber services. Dial number stored in M1 memory location. Adjust handset volume. M E M O R Y This cordless phone can store 10 telephone numbers that you can dial just by pressing p and one of the number buttons. -
Page 9: Changing Channels
O P E R A T I N G This cordless telephone operates at the maximum power allowed by the Federal Communications Commission (FCC). Even so, the handset and base can com- municate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office. -
Page 10: Answering System Operation
ANSWERING SYSTEM OPERATION Light goes on when handset is in use or battery is charging. Record a memo, or rewind tape during message playback Save messages. Volume Control Use the volume control on the side of the base to adjust the answering system volume. -
Page 11: Listening To Your Messages
ANSWERING SYSTEM OPERATION Ring Select Use the Ring Select switch on the back side of the base unit to select how many times the line will ring before the system answers a call. Set to 4 for four rings, or set to TS for Toll Saver. -
Page 12: Remote Access Code
ANSWERING SYSTEM OPERATION FROM A REMOTE TOUCH TONE PHONE Remote Access Code The Remote Access Code is a 3-digit code which lets you access your 7610 answering system away from your home or office. The factory setting is 123 (printed under the microcassette lid on the base).You can change this code to any 3-digit number between 100 and 999, except 323 and 523. -
Page 13: Answering System
Answering System 7610 Operation From a Remote Touch Tone Phone To access your answering system: 1 Dial your telephone number. 2 When the system answers, enter your 3-digit Remote Access Code. The system announces the number of messages received, then beeps twice and is ready to accept a command. See the other side of this card for a complete list of remote commands. - Page 14 COMMAND Play all messages Play only new messages Replay messages after playing messages Rewind Hold down Fast Forward Hold down Clear messages Stop ; press Record announcement press Change Remote Access Code Turn system on Turn system off COMMAND Play all messages Play only new messages Replay messages after playing messages...