Sign in today to find solutions:

Don't have an account? Sign up

 
EN
DATA PROJECTOR
MODEL
XD205U/XD205U-G/XD205R
SD205U/SD205R
User Manual
This User Manual is important to you.
Please read it before using your projector.
Next page ->

Summary of Contents

  • Page 1

    DATA PROJECTOR MODEL XD205U/XD205U-G/XD205R SD205U/SD205R User Manual This User Manual is important to you. Please read it before using your projector.

  • Page 2

    TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUT- LET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord.

  • Page 3: Table Of Contents

    Contents Important safeguards...4 Overview...6 Remote control ...8 Installation ...9 Basic connections...10 Preparation ...12 Basic operation ...13 Menu operation...15 Image adjustment ...18 Advanced feature...20 Lamp replacement ...22 Troubleshooting ...23 Indicators ...26 Specifications ... 27 Declaration of Conformity Model Number : XD205U/XD205U-G/XD205R/SD205U/SD205R Trade Name : MITSUBISHI ELECTRIC Responsible party :...

  • Page 4: Important Safeguards

    Water and moisture Do not use this projector near water or in contact with water. Accessories Do not place this projector on an unstable cart, stand, tripod, bracket or table.

  • Page 5

    Never put any heat-producing device under the projector to pre- vent the projector from being overheated. • Do not install the projector at a place that is unstable or subject to vibration. • Do not install the projector near any equipment that produces a strong magnetic field.

  • Page 6: Overview

    Overview 4 12 Control panel Terminal board EN-6 10 11 8 9 FOCUS ring ZOOM ring Control panel Air outlet grille Remote control sensor (Front) Air inlet grille Air inlet grille Terminal board Kensington Security Lock Standard connector 10 Air inlet grille 11 Speaker 12 Adjustment feet (front) 13 Adjustment feet (rear)

  • Page 7

    Bottom side Remote control This model does not have this function. Lamp cover Adjustment feet (rear) Adjustment feet (front) Caution: Do not replace the lamp immediately after using the pro- jector because the lamp would be extremely hot and it may cause burns.

  • Page 8: Remote Control

    When the remote control is pointed to the screen, the distance from the remote control to the projector via the screen should be 5 m or less. However, the operation distance varies depending on the type of the screen used.

  • Page 9: Installation

    Put a hard board under the pro- jector to facilitate ventilation. • Place the projector at least 50 cm (or 20 inch) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

  • Page 10: Basic Connections

    Make sure that the connected device is turned off before starting connection. • Plug in the power cords of the projector and the connected devices firmly. When unplugging, hold and pull the plug. Do not pull the cord. • When the projector and the connected devices are located too close to each other, the projected image may be affected by their interference.

  • Page 11

    • After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, and then boot up the computer.

  • Page 12: Preparation

    Remove the lens cap. Warning: • Do not look into the lens directly when the projector is on. • The lens cap is for protecting the lens. If you leave the lens cap on the lens with the projector turned on, it may be deformed because of heat build-up.

  • Page 13: Basic Operation

    • If the power cord is unplugged from the wall outlet before the projector is cooled down completely after use, the fans may start rotating when the power cord is plugged in next time and the POWER button may not function. In this case, wait for the fans to stop and press the POWER button to light the indicator.

  • Page 14

    The lamp can’t be lit again for one minute after turned off for safety purpose. It will take another one minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button.

  • Page 15: Menu Operation

    Menu operation IMAGE CONTRAST BRIGHTNESS WHITE ENHANCE COLOR TEMP . COLOR TINT SHARPNESS GAMMA MODE INSTALLATION AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR LAMP MODE IMAGE REVERSE FEA TURE MENU POSITION CINEMA MODE VIDEO SIGNAL ANAMORPHIC PASSWORD FUNCTION LANGUAGE RESET ALL SIGNAL...

  • Page 16

    BLACK, which will be displayed when there is no signal input from the source. the projector operating noise is reduced, resulting in a longer lamp replacement interval. • When the lamp mode is switched, the projected image may flicker. This is not a product malfunc- tion.

  • Page 17

    HORIZ. POSITION... Use to adjust the horizontal position of the image. VERT. POSITION ... Use to adjust the vertical position of the image. FINE SYNC ... Use to synchronize the projector with the PC input signal TRACKING... Use to eliminate image noise such as wide stripes.

  • Page 18: Image Adjustment

    Image adjustment Image adjustment You can adjust the image using the IMAGE menu. opt. IMAGE CONTRAST BRIGHTNESS WHITE ENHANCE COLOR TEMP. COLOR TINT SHARPNESS GAMMA MODE To control the white-to-black level of the image : Adjust CONTRAST in the IMAGE menu. Press the increase the contrast and the button to reduce it.

  • Page 19

    Adjustment of the image from the computer This projector adjusts the format of the video signal supplied from the computer. However, sometimes images are not projected correctly owing to the type of the computer used. When the image from the computer isn’t projected correctly, press the AUTO POSITION button.

  • Page 20: Advanced Feature

    Advanced feature Still To stop the motion in the image temporarily (or to display a still image): Press the STILL button on the remote control. • The image will freeze temporarily. To resume the motion in the image: Press the STILL button on the remote control again. Important: •...

  • Page 21

    MENU ACCESS ...All the buttons except for the POWER button on the projector are disabled. (The buttons on the remote con- trol are enabled.) You can use this mode as a measure of pre- vention of wrong operation by children and restriction on operation by other than specified users.

  • Page 22: Lamp Replacement

    • Be sure not to drop the lamp lid screw into the projector. Also be sure not to put metal or any flammable objects inside because it may cause fire or electric shock. If any objects should fall inside, unplug and contact your dealer.

  • Page 23: Troubleshooting

    • If the projector was turned off before the lamp cooled down completely, the fans may start rotating and the POWER button may not function when you plug the power cord into the wall outlet next time. Wait for the fans to stop and press the POWER button to turn on the lamp again.

  • Page 24

    Adjust the projector and the screen so that they are perpendicular to each other. (See page 12.) • This symptom is normal for a DLP projector and is not a malfunction. (A very small number of pixels may stay lit or out, but such symptom is not a malfunction. Pixels of 99.99% or more are effective.) •...

  • Page 25

    Cleaning of the projector and the ventilation slots Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.

  • Page 26: Indicators

    Indicators This projector has two indicators, each of which shows the operation condition of the projector. The following offer solutions to possible problems. If these problem persist, turn the projector off and consult your dealer. STATUS indicator Normal condition POWER...

  • Page 27: Specifications

    This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington Technology Group below.

  • Page 28

    Specifications (continued) Connectors pin No. Dimensional drawings (unit : mm) What’s included in the box AC power cord for US 02552-0063-01 for EU 02552-0066-01 for UK 02552-0065-01 1 RGB cable for PC 02552-0072-00 1 VIDEO cable 02552-0068-00 Replacement part (Option / Not included in the box) Spare lamp 499B045-20 VLT-XD205LP...

  • Page 29

    Specification of RGB signals in each computer mode of the projector resolution Signal mode (H x V) TV60, 480i(525i) TV50, 576i(625i) 1080i 60 (1125i 60) 1080i 50 (1125i 50) 480p (525p) 576p (625p) 720p 60 (750p 60) 720p 50 (750p 50)

  • Page 30

    MITSUBISHI Projector Contact Information North America MESCA (Mitsubishi Electric Sales Canada Inc.) http://www.mitsubishielectric.ca Information Technologies Group, 4299 14th Avenue, Markham, Ontario L3R 0J2, Canada Sales & Technical Inquires Phone :+1-(800) 450-6487 :+1-(905) 475-7958 E-mail :projectors@mitsubishielectric.ca Customer Care E-mail :support@mitsubishielectric.ca MDEA (Mitsubishi Digital Electronics America, Inc.) (Warranty Registration) http://www.mitsubishi-presentations.com/...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: