Page 2 Vigor2860 Series VDSL2 Security Firewall User’s Guide Version: 4.0 Firmware Version: V3.8.2 (For future update, please visit DrayTek web site) Date: November 19, 2015 Vigor2860 Series User’s Guide...
Page 3 Web registration is preferred. You can register your Vigor router via http://www.DrayTek.com. Firmware & Tools Updates  Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. http://www.DrayTek.com...
Page 4 Product: Vigor2860 Series Router DrayTek Corp. declares that Vigor2860 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE 1999/5/EC, ErP 2009/125/EC and RoHS 2011/65/EU. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
Page 5: Table Of Contents
II-1-2-1 Details Page for PPPoE in WAN1 (Physical Mode: VDSL2) ......81 II-1-2-2 Details Page for MPoA/Static or Dynamic IP in WAN1 (Physical Mode: VDSL2) 84 II-1-2-3 Details Page for PPPoE/PPPoA in WAN1 (Physical Mode: ADSL) ....87 Vigor2860 Series User’s Guide...
Page 6 II-3-4 Port Triggering........................ 179 II-4 Applications ..........................181 Web User Interface ........................183 II-4-1 Dynamic DNS ......................... 183 II-4-2 LAN DNS / DNS Forwarding ..................187 II-4-3 Schedule......................... 190 II-4-4 RADIUS/TACACS+ ......................192 II-4-4-1 External RADIUS ................ 192 Vigor2860 Series User’s Guide...
Page 7 III-1-2 General Setup ....................... 256 III-1-3 Security.......................... 258 III-1-4 Access Control ......................260 III-1-5 WPS..........................261 III-1-6 WDS ..........................264 III-1-7 Advanced Setting ......................267 III-1-8 Station Control....................... 270 III-1-9 AP Discovery ......................... 271 III-1-10 Station List........................272 Vigor2860 Series User’s Guide...
Page 8 V-2-4 User Account........................353 V-2-5 User Group........................357 V-2-6 Online User Status ......................359 V-3 Certificate Management......................360 Web User Interface ........................361 V-3-1 Local Certificate ......................361 V-3-2 Trusted CA Certificate....................365 V-3-3 Certificate Backup ......................367 Vigor2860 Series User’s Guide viii...
Page 9 V-4-4 Log & Alert ........................378 Application Notes ........................379 A-1 CVM Application - How to manage the CPE (router) through Vigor2860 series? . 379 A-2 CVM Application - How to build the VPN between remote devices and Vigor2860 series? ..................... 383 A-3 CVM Application - How to upgrade CPE firmware through Vigor2860 series? ..
Page 10 VII-4-6 Traffic Graph ........................ 528 VII-4-7 Rogue AP Detection..................... 529 VII-4-8 Event Log ........................532 VII-4-9 Total Traffic ........................532 VII-4-10 Station Number ......................533 VII-4-11 Load Balance ......................533 VII-4-12 Function Support List ....................534 Application Notes ........................535 Vigor2860 Series User’s Guide...
Page 11 Web User Interface ........................584 IX-1-1 Dial-out Triggering......................584 IX-1-2 Routing Table........................ 585 IX-1-3 ARP Cache Table ......................586 IX-1-4 IPv6 Neighbour Table ....................587 IX-1-5 DHCP Table ........................587 IX-1-6 NAT Sessions Table ..................... 588 Vigor2860 Series User’s Guide...
Page 12 IX-6 Problems for 3G/4G Network Connection ................608 IX-7 Backing to Factory Default Setting If Necessary ..............609 IX-8 Contacting DrayTek .........................611 Appendix I: VLAN Applications on Vigor Router ................612 Part X Telnet Commands....................620 Accessing Telnet of Vigor2860 ....................... 621 Vigor2860 Series User’s Guide...
Page 13: Part I Installation
This part will introduce Vigor router and guide to install the device in hardware and software.
Page 15: Introduction
Vigor2860 series is a VDSL2 router. It integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES, the router increases the performance of VPN greatly, and offers several protocols (such as IPsec/PPTP/L2TP) with VPN tunnels.
Page 16: I-1-1 Indicators And Connectors
The port is connected. WAN2 The port is disconnected. (Giga) Blinking The data is transmitting. Right The port is connected with 1000Mbps. The port is connected with 10/100Mbps Left The port is connected. GigaL The port is disconnected. Vigor2860 Series User’s Guide...
Page 17 Connecters for local network devices. Connecter for a power adapter. ON/OFF Power Switch. SIM Card Slot Connector for a SIM card. Magnetic antenna must be installed on the antenna socket before connecting to Vigor router. Antenna Socket Vigor2860 Series User’s Guide...
Page 18 SIM card slot. While installing the SIM card into the card slot, note that back plate of the SIM card slot must be removed first and the direction of card notch must be on the left side. Vigor2860 Series User’s Guide...
Page 19: I-1-1-2 For Vigor2860Ac / Vigor2860N-Plus / Vigor2860N/Vigor2860Ln
It will blink slowly while wireless traffic goes through. Blinking ACT and WLAN LEDs blink quickly and simultaneously when WPS is working, and will return to normal condition after two minutes. (You need to setup WPS Vigor2860 Series User’s Guide...
Page 20 Press the button and release it within 2 seconds. When the wireless function is ready, the green LED will be on.  Press the button and release it within 2 seconds to turn off the WLAN function. When the wireless function is not ready, the Vigor2860 Series User’s Guide...
Page 21 Connecters for local network devices. Connecter for a power adapter. ON/OFF Power Switch. SIM Card Slot Connector for a SIM card. Both magnetic antennas must be installed on the antenna socket before connecting to Vigor router. Antenna Socket Vigor2860 Series User’s Guide...
Page 22 SIM card slot. While installing the SIM card into the card slot, note that back plate of the SIM card slot must be removed first and the direction of card notch must be on the left side. Vigor2860 Series User’s Guide...
Page 23 Wrong installation might cause bad signal of wireless connection. Therefore, pay attention to the installation of antennas by referring to the following illustration. Holes for Antennas with Socket Holes for Antennas without Socket Vigor2860 Series User’s Guide...
Page 24: I-1-1-3 For Vigor2860Vac / Vigor2860Vn-Plus
The port is connected with 1000Mbps. The port is connected with 10/100Mbps Left The port is connected. GigaL The port is disconnected. Blinking The data is transmitting. Right The port is connected with 1000Mbps. The port is connected with 10/100Mbps Vigor2860 Series User’s Guide...
Page 25 Connecter for local network devices or modem for accessing Internet. GigaLAN (1-6) Connecters for local network devices. Phone 1/2 Connecter for analog phone(s). Line Connector for PSTN life line. Connecter for a power adapter. ON/OFF Power Switch. Vigor2860 Series User’s Guide...
Page 26: Hardware Installation
Power on the device by pressing down the power switch on the rear panel. The system starts to initiate. After completing the system test, the ACT LED will light up and start blinking. (For the hardware connection, we take “n” model as an example.) Vigor2860 Series User’s Guide...
Page 27: I-2-2 Installing Usb Printer To Vigor Router
You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows 7. For other Windows system, please visit www.DrayTek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients).
Page 28 A dialog will appear. Click Add a local printer and click Next. In this dialog, choose Create a new port. In the field of Type of port, use the drop down list to select Standard TCP/IP Port. Then, click Next. Vigor2860 Series User’s Guide...
Page 29 In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Hostname or IP Address and type 192.168.1.1 as the Port name. Then, click Next. Click Standard and choose Generic Network Card. Vigor2860 Series User’s Guide...
Page 30 Now, your system will ask you to choose right name of the printer that you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next. Type a name for the chosen printer. Click Next. Vigor2860 Series User’s Guide...
Page 31 10. Choose Do not share this printer and click Next. 11. Then, in the following dialog, click Finish. Vigor2860 Series User’s Guide...
Page 32 12. The new printer has been added and displayed under Printers and Faxes. Click the new printer icon and click Printer server properties. 13. Edit the property of the new printer you have added by clicking Configure Port. Vigor2860 Series User’s Guide...
Page 33 14. Select "LPR" on Protocol, type p1 (number 1) as Queue Name. Then click OK. Next please refer to the red rectangle for choosing the correct protocol and LPR name. Vigor2860 Series User’s Guide...
Page 34 If please visit www.draytek.com to find out the printer list. Open Support >FAQ/Application Notes; find out the link of USB>>Printer Server and click Then, click the What types of printers are compatible with Vigor router? link.
Page 35: Accessing Web Page
Please type “admin/admin” as the Username/Password and click Login. Info If you fail to access to the web configuration, please go to “Trouble Shooting” for detecting and solving your problem. Vigor2860 Series User’s Guide...
Page 36 The web page can be logged out according to the chosen condition. The default setting is Auto Logout, which means the web configuration system will logout after 5 minutes without any operation. Change the setting for your necessity. Vigor2860 Series User’s Guide...
Page 37: Changing Password
New Password and Confirm Password. Then click OK to continue. Info The maximum length of the password you can set is 23 characters. Now, the password has been changed. Next time, use the new password to access the Web user interface for this router. Vigor2860 Series User’s Guide...
Page 38 Info Even the password is changed, the Username for logging onto the web user interface is still “admin”. Vigor2860 Series User’s Guide...
Page 39: Dashboard
IPv6 Internet Access, Interface (physical connection), Security and Quick Access. Click Dashboard from the main menu on the left side of the main page. A web page with default selections will be displayed on the screen. Refer to the following figure: Vigor2860 Series User’s Guide...
Page 40: I-5-1 Virtual Panel
For detailed information about the LED display, refer to I-1-1 LED Indicators and Connectors. A name with a link (e.g., Router Name, Current Time, WAN1~4 and etc.) below means you can click it to open the configuration page for modification. Vigor2860 Series User’s Guide...
Page 41: I-5-3 Quick Access For Common Used Menu
LAN are located on the bottom of this page. Scroll down the page to find them and use them if required. Note that there is a plus ( ) icon located on the left side of VPN/LAN. Click it to review the VPN connection(s) used presently. Vigor2860 Series User’s Guide...
Page 42: I-5-4 Topology - Switch Management
Moreover, move the mouse cursor on the icon (e.g., Phone 1, Phone 2, DialPlan and SIP Accounts) displayed on the screen, the system will open related configuration web page immediately. Below shows the topology of switch management: Vigor2860 Series User’s Guide...
Page 43: I-5-5 Gui Map
The functions/settings modified under Web Console also can be reviewed on the web user interface. Click the Web Console icon on the top of the main screen to open the following screen. Vigor2860 Series User’s Guide...
Page 44 Vigor2860 Series User’s Guide...
Page 45: I-5-7 Config Backup
System Maintenance>>Configuration Backup. Simply click the icon on the top of the main screen and a pop up dialog will appear. Click Save to store the setting. Click this icon to exit the web user interface. Vigor2860 Series User’s Guide...
Page 46: I-5-9 Online Status
Such page displays the physical connection status such as LAN connection status, WAN connection status, ADSL information, and so on. Vigor2860 Series User’s Guide...
Page 47 WAN interface. RX Packets - Displays the total number of received packets at the WAN interface. RX Rate - Displays the speed of received octets at the WAN interface. Detailed explanation (for IPv6) is shown below: Vigor2860 Series User’s Guide...
Page 48: I-5-9-2 Virtual Wan
Internet. Such page displays the virtual WAN connection information. Virtual WAN are used by TR-069 management, VoIP service and so on. The field of Application will list the purpose of such WAN connection. Vigor2860 Series User’s Guide...
Page 49: Quick Start Wizard
WAN1, WAN2, WAN3/LTE and WAN4 will bring up different configuration page. Refer to the following for detailed information. In which, WAN3 will be treated as USB WAN or LTE WAN according to the USB modem or SIM Card used for accessing Internet. Vigor2860 Series User’s Guide...
Page 50: I-6-1 For Wan1 (Adsl/Vdsl2)
ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. In addition, the field of For ADSL Only will be available only when ADSL is detected. Then click Next for next step. Vigor2860 Series User’s Guide...
Page 51 Type the IP address as the default gateway. Primary DNS Type in the primary IP address for the router. Secondary DNS Type in secondary IP address for necessity in the future. Back Click it to return to previous setting page. Vigor2860 Series User’s Guide...
Page 52 Note: The maximum length of the password you can set is 62 characters. Confirm Password Retype the password. Back Click it to return to previous setting page. Next Click it to get into the next setting page. Cancel Click it to give up the quick start wizard. Vigor2860 Series User’s Guide...
Page 53 After finished the above settings, click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 54 Type the IP address if Fixed IP is enabled. Subnet Mask Type the subnet mask. Default Gateway Type the IP address as the default gateway. Primary DNS Type in the primary IP address for the router. Vigor2860 Series User’s Guide...
Page 55 Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 56: I-6-2 For Wan2 (Ethernet)/(Wireless 2.4G)
On the next page as shown below, please select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step. Vigor2860 Series User’s Guide...
Page 57 Note: The maximum length of the user name you can set is 63 characters. Password Assign a valid password provided by the ISP. Note: The maximum length of the password you can set is 62 characters. Vigor2860 Series User’s Guide...
Page 58 Please manually enter the Username/Password provided by your ISP. Click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 59 Assign a specific valid user name provided by the ISP. Note: The maximum length of the user name you can set is 63 characters. Password Assign a valid password provided by the ISP. Note: The maximum length of the password you can set is 62 Vigor2860 Series User’s Guide...
Page 60 Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 61 Type in the primary IP address for the router. Secondary DNS Type in secondary IP address for necessity in the future. Back Click it to return to previous setting page. Next Click it to get into the next setting page. Vigor2860 Series User’s Guide...
Page 62 Choose WAN2 as the WAN Interface and choose Ethernet as the Physical Mode. Click the Next button. The following page will be open for you to specify Internet Access Type. Click DHCP as the Internet Access type. Simply click Next to continue. Vigor2860 Series User’s Guide...
Page 63 Click it to return to previous setting page. Next Click it to get into the next setting page. Cancel Click it to give up the quick start wizard. After finished the settings above, click Next for viewing summary of such connection. Vigor2860 Series User’s Guide...
Page 64 Click the Next button. The following page will be open for you to specify Internet Access Type. Click Static IP as the Internet Access Type. Simply click Next to continue. Available settings are explained as follows: Item Description WAN IP Type the IP address. Vigor2860 Series User’s Guide...
Page 65 WPA2 client and the encryption key should be entered in PSK. Back Click it to return to previous setting page. Next Click it to get into the next setting page. Cancel Click it to give up the quick start wizard. Vigor2860 Series User’s Guide...
Page 66 Click the AP Discovery button to choose your Wireless AP. You can also set the Wireless AP information directly and skip the next 2 steps. Click the Scan button of the popup window and wait for a few seconds. Select your Wireless AP and click the Add to button. Vigor2860 Series User’s Guide...
Page 67 Pass Phrase. Then click Next for next step. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 68 Wireless LAN (2.4GHz) would be also modified. Security Mode The mode to connect to the Wireless AP. Disable – The Router connects to the wireless AP  Vigor2860 Series User’s Guide...
Page 69 Click the AP Discovery button to choose your Wireless AP. You can also set the Wireless AP information directly and skip the next 2 steps. Click the Scan button of the popup window and wait for a few seconds. Vigor2860 Series User’s Guide...
Page 70 Pass Phrase. Then click Next for next step. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 71: I-6-3 For Wan3/Wan4 (Usb)
15 characters. Modem Initial String – Such value is used to initialize USB modem. Please use the default value. If you have any question, please contact to your ISP. The maximum length of Vigor2860 Series User’s Guide...
Page 72 Then, click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 73: I-6-4 For Lte Wan
If you choose 4G/3G/2G as network mode, the router will choose a suitable one according to the actual wireless signal automatically. APN Name – APN means Access Point Name which is provided and required by some ISPs. Vigor2860 Series User’s Guide...
Page 74 Please type in required information originally provided by your ISP. Then, click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Vigor2860 Series User’s Guide...
Page 75: Service Activation Wizard
Service Activation Wizard is a tool which allows you to use trial version of WCF directly without accessing into the server (MyVigor) located on http://myvigor.draytek.com. For using Web Content Filter Profile, please refer to later section Web Content Filter Profile for detailed information.
Page 76 Commtouch is the web content filter based on Commtouch operated in the worldwide. There is a 30-day trial period. After trial, you can purchase DrayTek's prepared Commtouch GlobalView WCF package from retailing outlets. BPjM is WCF for German Speaking users. The fragfINN is whitelist for German Speaking users.
Page 77 The valid time for the free trial of these services is one month. When all the trial editions for various web content filters had been enabled, the configuration page of Service Activation Wizard will be invalid as shown below. Vigor2860 Series User’s Guide...
Page 78: Registering Vigor Router
Please login the web configuration interface of Vigor router by typing “admin/admin” as User Name / Password. Click Support Area>>Production Registration from the home page. A Login page will be shown on the screen. Please type the account and password that you created previously. And click Login. Vigor2860 Series User’s Guide...
Page 79 Account for MyVigor to create your own one. Please read the articles on the Agreement regarding user rights carefully while creating a user account. The following page will be displayed after you logging in MyVigor. From this page, please click Add or Product Registration. Vigor2860 Series User’s Guide...
Page 80 Registration Date). After adding the basic information for the router, please click Submit. When the following page appears, your router information has been added to the database. After clicking OK, you will see the following page. Your router has been registered to myvigor website successfully. Vigor2860 Series User’s Guide...
Page 81: Part Ii Connectivity
PC in the local area network. DNS, LAN DNS, IGMP, LDAP, UpnP, IGMP, WOL, RADIUS, SMS, Bonjour Static Route, Load-Balance/Route Policy Vigor2860 Series User’s Guide...
Page 82: Wan
Users can use LAN ports on the router to access Internet. Also, they can access Internet via 802.11(a/b/g/n/ac) wireless standard, and enjoy the powerful firewall, bandwidth management, and VPN features of Vigor2860n series. Vigor2860 Series User’s Guide...
Page 83 Besides, 3G/4G USB Modem in WAN3/WAN4 also can be used as backup device. Therefore, when WAN1 and WAN2 are not available, the router will use 3.5G for supporting automatically. The supported 3G/4G USB Modem will be listed on DrayTek web site. Please visit www.draytek.com for more detailed information.
Page 84: Web User Interface
In default, WAN2 is disabled. If you want to enable it, simply click the WAN2 link and select Yes in the field of Enable. For Vigor2860 Series except Vigor2860L and Vigor2860Ln For Vigor2860L and Vigor2860Ln Available settings are explained as follows:...
Page 85: Ii-1-1-1 Wan1(Adsl/Vdsl2)
Vigor router will detect the physical line is connected by ADSL or VDSL2 automatically. Therefore, this page allows you to configure settings for ADSL and VDSL2 at one time. That is, it is not necessary for you to configure different profile settings for ADSL and VDSL2 respectively. Vigor2860 Series User’s Guide...
Page 86 Default or contact the dealer for assistance. Line Speed (Kpbs) If your choose According to Line Speed as the Load Balance Mode in previous page, please type the line speed for downloading and uploading for such WAN interface. The unit is kbps. Vigor2860 Series User’s Guide...
Page 87 WAN interface disconnects. All of the selected WAN disconnect – Such backup WAN will be activated only when all master WAN interfaces disconnect. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 88: Ii-1-1-2 Wan2 (Ethernet)/(Wireless 2.4G)
WAN2 can be configured for physical mode of Ethernet or Wireless 2.4G. Vigor2860 Series User’s Guide...
Page 89 WAN interfaces in connection status. Active When If you choose Failover as the Active Mode, Active When will appear. Please specify which WAN will be the Backup interface. Vigor2860 Series User’s Guide...
Page 90: Ii-1-1-3 Wan3/Wan4 (Usb)
WAN interface. The unit is kbps. Active Mode Choose Always On to make the WAN1 connection being activated always. Load Balance: Check this box to enable auto load balance function for such WAN interface. Vigor2860 Series User’s Guide...
Page 91 WAN interface disconnects. All of the selected WAN disconnect – Such backup WAN will be activated only when all master WAN interfaces disconnect. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 92: Ii-1-2 Internet Access
LTE/WAN4) for Internet Access. Due to different Physical Mode for WAN interface, the Access Mode for these connections also varies. Refer to the following figures for examples. Access Mode for ADSL/VDSL2, Access Mode for LTE (for L model only), Access Mode for Etherenet / USB, Vigor2860 Series User’s Guide...
Page 93 Mode) to setup IPv6 Internet Access Mode for WAN interface. Advanced This button allows you to configure DHCP client options. DHCP packets can be processed by adding option number and data information when such function is enabled and configured. Vigor2860 Series User’s Guide...
Page 94 Option Number – Type a number for such function. DataType – Choose the type (ASCII or Hex) for the data to be stored. Data – Type the content of the data to be processed by the function of DHCP option. Vigor2860 Series User’s Guide...
Page 95: Ii-1-2-1 Details Page For Pppoe In Wan1 (Physical Mode: Vdsl2)
For Wireless LAN – It is available for n model. If you check this box, PCs on the same wireless network can use another set of PPPoE session (different with the Host PC) to access into Internet. Vigor2860 Series User’s Guide...
Page 96 Enter your allocated username, password and authentication parameters according to the information provided by your ISP. Username – Type in the username provided by ISP in this field. Password – Type in the password provided by ISP in this field. Vigor2860 Series User’s Guide...
Page 97 All the schedules can be set previously in Applications >> Schedule web page and you can use the number that you have set in that web page. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 98 Primary/Secondary Ping IP – If you choose Ping Detect as detection mode, you have to type Primary or Secondary IP address in this field for pinging.  Ping Gateway IP – If you choose Ping Detect as detection Vigor2860 Series User’s Guide...
Page 99 WAN IP Alias. You can set up to 32 public IP addresses other than the current one you are using. Notice that this setting is available for WAN1 only. Type the additional WAN IP address and check the Enable box. Then click OK to exit the dialog. Vigor2860 Series User’s Guide...
Page 100 DNS Server IP Address Type in the primary IP address for the router. If necessary, type in secondary IP address for necessity in the future. After finishing all the settings here, please click OK to activate them. Vigor2860 Series User’s Guide...
Page 101: Ii-1-2-2 Details Page For Mpoa/Static Or Dynamic Ip In Wan1 (Physical Mode: Vdsl2) 84 Ii-1-2-3 Details Page For Pppoe/Pppoa In Wan1 (Physical Mode: Adsl)
Protocol - Drop down the list to choose the one (PPPoE or PPPoA) provided by ISP. If you have already used Quick Start Wizard to set the protocol, then it is not necessary for you to change any settings in this group. Vigor2860 Series User’s Guide...
Page 102 It means Max Transmit Unit for packet. Path MTU Discovery – It is used to detect the maximum MTU size of a packet not to be segmented in specific transmit path. Click Detect to open the following dialog. Vigor2860 Series User’s Guide...
Page 103 WAN IP Alias - If you have multiple public IP addresses and would like to utilize them on the WAN interface, please use WAN IP Alias. You can set up to 8 public IP addresses other than the current one you are using. Vigor2860 Series User’s Guide...
Page 104 LANs to send packets to each other via an ATM backbone. To use MPoA/Static or Dynamic IP as the accessing protocol of the Internet, select MPoA /Static or Dynamic IP from the WAN>>Internet Access >>WAN1 page. The following web page will appear. Vigor2860 Series User’s Guide...
Page 105 WAN Connection Such function allows you to verify whether network Detection connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system to Vigor2860 Series User’s Guide...
Page 106 (user profiles) under User Management will be ignored. And all of the filter rules defined and enabled in Firewall menu will be activated. Bridge Subnet – Make a bridge between the selected LAN subnet and such WAN interface. Vigor2860 Series User’s Guide...
Page 107 Default MAC Address – Type in MAC address for the router. You can use Default MAC Address or specify another MAC address for your necessity. Specify a MAC Address – Type in the MAC address for the Vigor2860 Series User’s Guide...
Page 108: Ii-1-2-4 Details Page For Mpoa/Static Or Dynamic Ip In Wan1 (Physical Mode: Adsl) .90 Ii-1-2-5 Details Page For Pppoe In Wan2 (Physical Mode: Ethernet)
The maximum length of the password you can set is 62 characters. Index (1-15) in Schedule Setup - You can type in four sets of time schedule for your request. All the schedules can be set Vigor2860 Series User’s Guide...
Page 109 IP Address Assignment Usually ISP dynamically assigns IP address to you each time Method (IPCP) you connect to it and request. In some case, your ISP provides service to always assign you the same IP address Vigor2860 Series User’s Guide...
Page 110: Ii-1-2-6 Details Page For Static Or Dynamic Ip In Wan2 (Physical Mode: Ethernet)
If you have a public subnet, you could assign an IP address or many IP address to the WAN interface. To use Static or Dynamic IP as the accessing protocol of the internet, please click the Static or Dynamic IP tab. The following web page will be shown. Vigor2860 Series User’s Guide...
Page 111 WAN detection. If you choose Ping Detect as the detection mode, you have to type required settings for the following items.  Primary/Secondary Ping IP – If you choose Ping Detect as Vigor2860 Series User’s Guide...
Page 112 WAN interface. WAN IP Network Settings This group allows you to obtain an IP address automatically and allows you type in IP address manually. WAN IP Alias - If you have multiple public IP addresses and Vigor2860 Series User’s Guide...
Page 113 Type in the primary IP address for the router if you want to use Static IP mode. If necessary, type in secondary IP address for necessity in the future. After finishing all the settings here, please click OK to activate them. Vigor2860 Series User’s Guide...
Page 114: Ii-1-2-7 Details Page For Pptp/L2Tp In Wan2 (Physical Mode: Ethernet)
It means Max Transmit Unit for packet. Path MTU Discovery – It is used to detect the maximum MTU size of a packet not to be segmented in specific transmit path. Vigor2860 Series User’s Guide...
Page 115 Specify an IP address – Click this radio button to specify some data.  IP Address – Type the IP address.  Subnet Mask – Type the subnet mask. After finishing all the settings here, please click OK to activate them. Vigor2860 Series User’s Guide...
Page 116: Ii-1-2-8 Details Page For Static Or Dynamic Ip In Wan2 (Physical Mode: Wireless 2.4G)
Such function allows you to verify whether network Detection connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect, Ping Detect or Always On for the system to execute for WAN detection. If you choose Ping Vigor2860 Series User’s Guide...
Page 117 ABCDEFGHIJKLM (or 26 hexadecimal digits leading by 0x, such as 0x4142434445464748494A4B4C4D). WEP keys – Four keys can be entered here, but only one  key can be selected at a time. The keys can be entered Vigor2860 Series User’s Guide...
Page 118 WPA2 client and the encryption key should be entered in PSK. Pass Phrase – The PSK. Either 8~63 ASCII characters, such as 012345678..(or 64 Hexadecimal digits leading by 0x, such as "0x321253abcde..."). After finishing all the settings here, please click OK to activate them. Vigor2860 Series User’s Guide...
Page 119: Ii-1-2-9 Details Page For 3G/4G Usb Modem (Ppp Mode) In Wan3/Wan4
It lists all of the modems supported by such router. 3G /4G USB Modem (PPP Click Enable for activating this function. If you click Disable, mode) this function will be closed and all the settings that you Vigor2860 Series User’s Guide...
Page 120 With the IP address(es) pinging, Vigor router can check if the WAN connection is on or off.  TTL (Time to Live) – Set TTL value of PING operation.  Ping Interval – Type the interval for the system to Vigor2860 Series User’s Guide...
Page 121: Ii-1-2-10 Details Page For 3G/4G Usb Modem (Dhcp Mode) In Wan3/Wan4
Type PIN code of the SIM card that will be used to access Internet. The maximum length of the PIN code you can set is 19 characters. Network Mode Force Vigor router to connect Internet with the mode specified here. If you choose 4G/3G/2G as network mode, Vigor2860 Series User’s Guide...
Page 122  Ping Retry – Type the number of times that the system is allowed to execute the PING operation before WAN disconnection is judged. After finishing all the settings here, please click OK to activate them. Vigor2860 Series User’s Guide...
Page 123: Ii-1-2-11 Details Page For 3G/4G Usb Modem (Dhcp Mode) In Lte Wan
Type the username (optional). The maximum length of the name you can set is 63 characters. Password Type the password (optional). The maximum length of the password you can set is 62 characters. Authentication Select None or PAP or CHAP. Vigor2860 Series User’s Guide...
Page 124  Ping Retry – Type the number of times that the system is allowed to execute the PING operation before WAN disconnection is judged. After finishing all the settings here, please click OK to activate them. Vigor2860 Series User’s Guide...
Page 125: Ii-1-2-12 Details Page For Ipv6 - Offline In Wan1/Wan2/Wan3/Wan4
IP address in this field for pinging.  TTL (Time to Live) –If you choose Ping Detect as detection mode, you have to type TTL value. Below shows an example for successful IPv6 connection based on PPP mode. Vigor2860 Series User’s Guide...
Page 126: Ii-1-2-14 Details Page For Ipv6 - Tspc In Wan1/Wan2/Wan3/Wan4
After getting the IPv6 prefix and starting router advertisement daemon (RADVD), the PC behind this router can directly connect to IPv6 the Internet. Vigor2860 Series User’s Guide...
Page 127 IP address in this field for pinging.  TTL (Time to Live) –If you choose Ping Detect as detection mode, you have to type TTL value. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 128: Ii-1-2-15 Details Page For Ipv6 - Aiccu In Wan1/Wan2/Wan3/Wan4
ID (e.g., T115394). Type the ID offered by Tunnel Broker. Subnet Prefix Type the subnet prefix address obtained from service provider. The maximum length of the prefix you can set is 128 characters. Vigor2860 Series User’s Guide...
Page 129 IP address in this field for pinging.  TTL (Time to Live) –If you choose Ping Detect as detection mode, you have to type TTL value. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 130: Ii-1-2-16 Details Page For Ipv6 - Dhcpv6 Client In Wan1/Wan2
(user profiles) under User Management will be ignored. And all of the filter rules defined and enabled in Firewall menu will be activated. Bridge Subnet – Make a bridge between the selected LAN Vigor2860 Series User’s Guide...
Page 131: Ii-1-2-17 Details Page For Ipv6 - Static Ipv6 In Wan1/Wan2
Delete – Click it to remove an existed entry. Current IPv6 Address Display current interface IPv6 address. Table Static IPv6 Gateway IPv6 Gateway Address - Type your IPv6 gateway address Configuration here. WAN Connection Such function allows you to verify whether network Vigor2860 Series User’s Guide...
Page 132 User Management will be ignored. And all of the filter rules defined and enabled in Firewall menu will be activated. Bridge Subnet – Make a bridge between the selected LAN subnet and such WAN interface. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 133: Ii-1-2-18 Details Page For Ipv6 - 6In4 Static Tunnel In Wan1/Wan2
IP address in this field for pinging.  TTL (Time to Live) –If you choose Ping Detect as detection mode, you have to type TTL value. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 134: Ii-1-2-19 Details Page For Ipv6 - 6Rd In Wan1/Wan2
Available settings are explained as follows: Item Description 6rd Mode Auto 6rd – Retrieve 6rd prefix automatically from 6rd service provider. The IPv4 WAN must be set as "DHCP". Static 6rd - Set 6rd options manually. Vigor2860 Series User’s Guide...
Page 135 TTL (Time to Live) –If you choose Ping Detect as detection mode, you have to type TTL value. After finished the above settings, click OK to save the settings. Below shows an example for successful IPv6 connection based on 6rd mode. Vigor2860 Series User’s Guide...
Page 136: Ii-1-3 Multi-Pvc/Vlan
WAN type may not configure the same VLAN tag value. Enable - Check this box to enable the port-based bridge function on this channel. P1 ~ P6 – Check the box(es) to build bridge connection on LAN. Vigor2860 Series User’s Guide...
Page 137 Add VLAN Header – Check the box to enable the following two options. VLAN Tag – Type the value as the VLAN ID number. Valid Vigor2860 Series User’s Guide...
Page 138 Enable – Click it to enable Bridge mode for such channel. Physical Members – Group the physical ports by checking the corresponding check box(es) for applying the bridge connection. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 139 WAN type to be built upon. In the Multi-PVC application, only the Ethernet WAN type is available. The user will be able to select the physical WAN interface the channel shall use here. Vigor2860 Series User’s Guide...
Page 140  If PPPoE/PPPoA Client is selected as WAN Setup, you have to configure the settings listed under ISP Access Setup. Enter your allocated username, password and authentication parameters according to the information provided by your ISP. Vigor2860 Series User’s Guide...
Page 141  Ping Interval – Type the interval for the system to execute the PING operation.  Ping Retry – Type the number of times that the system is allowed to execute the PING operation before WAN Vigor2860 Series User’s Guide...
Page 142 Static IP mode. If necessary, type in secondary IP address for necessity in the future. After finished the above settings, click OK to save the settings and return to previous page. Vigor2860 Series User’s Guide...
Page 143 It allows the enabled PVC channel to use the same ADSL connection settings of another PVC channel. Please choose the PVC channel via the drop down list. After finished the above settings, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 144: Ii-1-4 Wan Budget
WAN interface will be terminated. Send Mail Alert to Administrator – The system will send out a warning message to the administrator when the quota is running out. However, the connection charges will be calculated continuously. Vigor2860 Series User’s Guide...
Page 145: Ii-1-4-2 Monitor Page
Vigor router will reset the traffic record. For example, “3” means the third day of the cycle duration. After finished the above settings, click OK to save the settings. The monitor page displays the status WAN budget, including the duration and the usage. Vigor2860 Series User’s Guide...
Page 146 Send Mail Alert to Administrator is selected. Or, the system will send out SMS message to the administrator if Send SMS messages to Administrator is selected. Vigor2860 Series User’s Guide...
Page 147: Application Notes
TSPC, AICCU, DHCPv6 Client and Static IPv6. Access into the web user interface of Viogr2860. Open WAN>> Internet Access. Choose one of the WAN interfaces as the one supporting IPv6 service. Then, click the IPv6 button of the selected WAN. Vigor2860 Series User’s Guide...
Page 148 Access into the setting page for IPv6 service, it is not necessary for you to configure anything. Click OK and open Online Status. If the connection is successful, you will get the IP address for IPv4 and IPv6 at the same time. Vigor2860 Series User’s Guide...
Page 149 Vigor2860 Series User’s Guide...
Page 150 (In the following figure, the TSPC information is obtained from http://gogo6.com/ after applied for the service.) Click OK and open Online Status. If the connection is successful, the physical connection will be shown as follows: Vigor2860 Series User’s Guide...
Page 151 (In the following figure, the AICCU information is obtained from https://www.sixxs.net/main/ after applied for the service.) Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2860 Series User’s Guide...
Page 152  DHCPv6 Client Choose DHCPv6 Client. Click one of the identity associations and type the IAID number. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2860 Series User’s Guide...
Page 153  Static IPv6 Choose Static IPv6. Type IPv6 address, Prefix Length and Gateway Address. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2860 Series User’s Guide...
Page 154 Choose 6in4 Static Tunnel. Type remote endpoint IPv4 address, 6in4 IPv6 Address, LAN Routed Prefix and Tunnel TTL. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2860 Series User’s Guide...
Page 155  Choose 6rd. Type IPv4 Border Relay, IPv4 Mask Length, 6rd Prefix and 6rd Prefix Length. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2860 Series User’s Guide...
Page 156 In the field of DHCPv6 Server Configuration, when DHCPv6 service is enabled, you can assign available IPv6 address for the client manually. Info When both mechanisms are enabled, the client can determine which mechanism to be used (e.g., the default mechanism for Windows7 is RADVD). Vigor2860 Series User’s Guide...
Page 157 Use the Ping command to ping any IPv6 address indicating an IPv6 website. For example, www.kame.net is a website supporting IPv4 IP and IPv6 IP services. Its IPv6 address is seen with a format of 2001:200:dff:fff1:216:3eff:feb1:44d7. After getting the above message, it means the IPv6 service has been activated successfully. Vigor2860 Series User’s Guide...
Page 158 If not, only a steady turtle will be seen. If you can see a turtle dancing on the screen, that means IPv6 service is ready for you to access and utilize. Vigor2860 Series User’s Guide...
Page 159: Lan
IP address. As a part of the public subnet, the Vigor router will serve for IP routing to help hosts in the public subnet to communicate with other public hosts or servers outside. Therefore, the router should be set as the gateway for public hosts. Vigor2860 Series User’s Guide...
Page 160 You can group local hosts by physical ports and create up to 8 virtual LANs. To manage the communication between different groups, please set up rules in Virtual LAN (VLAN) function and the rate of each. Vigor2860 Series User’s Guide...
Page 161: Web User Interface
Allow to configure settings for each subnet respectively. Index - Display all of the LAN items. Status- Basically, LAN1 status is enabled in default. LAN2 –LAN6 and IP Routed Subnet can be observed by checking the box of Status. Vigor2860 Series User’s Guide...
Page 162 Internet Access server (PPPoE, PPTP, L2TP or DHCP server). Inter-LAN Routing Check the box to link two or more different subnets (LAN and LAN). When you finish the configuration, please click OK to save and exit this page. Vigor2860 Series User’s Guide...
Page 163: Ii-2-1-1 Details Page For Lan1 - Ethernet Tcp/Ip And Dhcp Setup
Disable Server – Let you manually assign IP address to every host in the LAN. Enable Relay Agent –Specify which subnet that DHCP server is located the relay agent should redirect the DHCP request  DHCP Server IP Address – It is available when Enable Vigor2860 Series User’s Guide...
Page 164 If the IP address of a domain name is already in the DNS cache, the router will resolve the domain name immediately. Otherwise, the router forwards the DNS query packet to the external DNS server by establishing a WAN (e.g. DSL/Cable) Vigor2860 Series User’s Guide...
Page 165: Ii-2-1-2 Details Page For Lan2 ~ Lan6 And Dmz
Enable Relay Agent - If you want to use another DHCP server in the network other than the Vigor Router’s, you can let Relay Agent help you to redirect the DHCP request to the specified location. DHCP Server IP Address – It is available when Enable Relay Vigor2860 Series User’s Guide...
Page 166 If the IP address of a domain name is already in the DNS cache, the router will resolve the domain name immediately. Otherwise, the router forwards the DNS query packet to the external DNS server by establishing a WAN (e.g. DSL/Cable) Vigor2860 Series User’s Guide...
Page 167: Ii-2-1-3 Details Page For Ip Routed Subnet
Start IP Address - Enter a value of the IP address pool for the DHCP server to start with when issuing IP addresses. If the 1st IP address of your router is 192.168.1.1, the starting IP address must be 192.168.1.2 or greater, but smaller than Vigor2860 Series User’s Guide...
Page 168: Ii-2-1-4 Details Page For Lan Ipv6 Setup
There are two configuration pages for LAN1/LAN2/LAN3/LAN4/LAN5/LAN6/DMZ Port, Ethernet TCP/IP and DHCP Setup (based on IPv4) and IPv6 Setup. Click the tab for each type and refer to the following explanations for detailed information. Below shows the settings page for IPv6. Vigor2860 Series User’s Guide...
Page 169 Such feature is used for the host without assigned IPv6 (ULA) configuration address to obtain IPv6 address automatically or have an IPv6 address specified manually via ULA configuration. It is convenient for communication among different subnets. Vigor2860 Series User’s Guide...
Page 170 Disable Server –Click it to disable DHCPv6 server. Start IPv6 Address / End IPv6 Address –Type the start and end address for IPv6 server. Advance setting More options are offered under the Advance setting. Click Edit to open the pop-up window. Vigor2860 Series User’s Guide...
Page 171 Extension WAN – Not only the IP address can be obtained from the primary WAN, but also the prefix for IPv6 LAN IP address can be assigned by extension WAN specified here. When you finish the configuration, please click OK to save and exit this page. Vigor2860 Series User’s Guide...
Page 172: Ii-2-2 Vlan
The multi-subnet can let a small businesses have much better isolation for multi-occupancy applications. Go to LAN page and select VLAN. The following page will appear. Click Enable to invoke VLAN function. Below is an example page in Vigor2860n: Vigor2860 Series User’s Guide...
Page 173 Choose one of them to make the selected VLAN mapping to the specified subnet only. For example, LAN1 is specified for VLAN0. It means that PCs grouped under VLAN0 can get the IP address(es) that specified by the subnet. Vigor2860 Series User’s Guide...
Page 174 Leave one VLAN untagged at least to prevent from not connecting to Vigor router due to unexpected error. Vigor2860 series features a hugely flexible VLAN system. In its simplest form, each of the Gigabit LAN ports can be isolated from each other, for example to feed different companies or departments but keeping their local traffic completely separated.
Page 175 (isolated) or common (able to communicate with each other). This is ideal for departmental or multi-occupancy applications. Info As for the VLAN applications, refer to “Appendix I: VLAN Application on Vigor Router” for more detailed information. Vigor2860 Series User’s Guide...
Page 176: Ii-2-3 Bind Ip To Mac
Each pair of IP and MAC address listed in ARP table can be selected and added to IP Bind List by clicking Add below. Select All Click this link to select all the items in the ARP table. Sort Reorder the table based on the IP address. Vigor2860 Series User’s Guide...
Page 177 PC. If not, no one of the PCs can access into Internet. And the web user interface of the router might not be accessed. When you finish the configuration, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 178: Ii-2-4 Lan Port Mirror
Select which ports are necessary to be mirrored for transmitting the packets. Mirrored Rx Port Select which ports are necessary to be mirrored for receiving the packets. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 179: Ii-2-5 Wired 802.1X
RADIUS or Local 802.1x) will be used for authenticating LAN user. 802.1x ports After enabling the function, simply specify the LAN port(s) to apply such function. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 180: Ii-2-6 Web Portal Setup
Display the number link which allows you to configure the profile. Status Display the content (Disable, URL Redirect or Message) of the profile. Interface Display the applied interface of the profile. Preview Open a preview window according to the configured settings. Vigor2860 Series User’s Guide...
Page 181 Position on Screen – The content of notice and the defined button can be shown upside (Top) or downside (Bottom) the text defined for message body. Vigor2860 Series User’s Guide...
Page 182 Check the box(es) representing different interfaces to be applied by such profile. The advantage is that each SSID (1/2/3/4) for wireless network can be applied with different web portal separately. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 183: Nat
Usually we use the 192.168.1.0/24 subnet for the router. As stated before, the NAT facility can map one or more IP addresses and/or service ports into different specified services. In other words, the NAT function can be achieved by using port mapping methods. Vigor2860 Series User’s Guide...
Page 184: Web User Interface
The port redirection can only apply to incoming traffic. To use this function, please go to NAT page and choose Port Redirection web page. The Port Redirection Table provides 40 port-mapping entries for the internal hosts. Vigor2860 Series User’s Guide...
Page 185 Display the IP address of the internal host providing the service. Status Display if the profile is enabled (v) or not (x). Press any number under Index to access into next page for configuring port redirection. Available settings are explained as follows: Vigor2860 Series User’s Guide...
Page 186 80 to avoid conflict, such as 8080. This can be set in the System Maintenance >>Management Setup. You then will access the admin screen of by suffixing the IP address with 8080, e.g., http://192.168.1.1:8080 instead of port 80. Vigor2860 Series User’s Guide...
Page 187 Vigor2860 Series User’s Guide...
Page 188: Ii-3-2 Dmz Host
Click DMZ Host to open the following page. You can set different DMZ host for each WAN interface. Click the WAN tab to switch into the configuration page for that WAN. Vigor2860 Series User’s Guide...
Page 189 IP address will be shown on the following screen. Click OK to save the setting. DMZ Host for WAN2, WAN3, or WAN4 is slightly different with WAN1. Active True IP selection is available for WAN1 only. See the following figure. Vigor2860 Series User’s Guide...
Page 190 When you have selected one private IP from the above dialog, the IP address will be shown on the screen. Click OK to save the setting. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 191: Ii-3-3 Open Ports
Inactive or Active state. To add or edit port settings, click one index number on the page. The index entry setup page will pop up. In each index entry, you can specify 10 port ranges for diverse services. Vigor2860 Series User’s Guide...
Page 192 Specify the starting port number of the service offered by the local host. End Port Specify the ending port number of the service offered by the local host. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 193: Ii-3-4 Port Triggering
Display the protocol for the incoming data of such triggering profile. Incoming Port Display the port for the incoming data of such triggering profile. Status Display if the rule is active or de-active. Click the index number link to open the configuration page. Vigor2860 Series User’s Guide...
Page 194 (TCP, UDP or TCP/UDP) for the incoming data of such triggering profile. Incoming Port Type the port or port range for the incoming packets. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 195: Applications
FTP, Mail or Web server inside LAN, you can specify specific private IP address (es) to correspondent servers. Thus, even the remote PC is adopting public DNS as the DNS server, the LAN DNS resolution on Vigor2860 series will respond the specified private IP address.
Page 196 Wake on LAN (WOL) of this router. In addition, such PC must have installed a network card supporting WOL function. By the way, WOL function must be set as “Enable” on the BIOS setting. Vigor2860 Series User’s Guide...
Page 197: Web User Interface
Account, and choose correct Service Provider: dyndns.org, type the registered hostname: hostname and domain name suffix: dyndns.org in the Domain Name block. The following two blocks should be typed your account Login Name: test and Password: test. Vigor2860 Series User’s Guide...
Page 198 WAN1/WAN2/WAN3/WAN4/LTE as the first channel for such account. If WAN1/WAN2/WAN3 /WAN4/LTE fails, the router will use another WAN interface instead. WAN1/WAN2/WAN3/WAN4/LTE Only - While connecting, the router will use WAN1/WAN2/WAN3/WAN4/LTE as the Vigor2860 Series User’s Guide...
Page 199 WAN IP. When the WAN IP used by Vigor router is private IP, this function can detect the public IP used by the NAT router and use the detected IP address for DDNS update. Vigor2860 Series User’s Guide...
Page 200 Uncheck Enable Dynamic DNS Setup, and click Clear All button to disable the function and clear all accounts from the router. Click the Index number you want to delete and then click Clear All button to delete the account. Vigor2860 Series User’s Guide...
Page 201: Ii-4-2 Lan Dns / Dns Forwarding
FTP, Mail or Web server inside LAN, you can specify specific private IP address (es) to correspondent servers. Thus, even the remote PC is adopting public DNS as the DNS server, the LAN DNS resolution on Vigor2860 series will respond the specified private IP address.
Page 202 In general, one domain name maps with one IP address. If required, you can configure two IP addresses mapping with the same domain name. Add – Click it to open a dialog to type the host’s IP address. Vigor2860 Series User’s Guide...
Page 203 Type the domain name for such profile. DNS Server IP Address Type the IP address of the DNS server you want to use for DNS forwarding. Click OK button to save the settings. A new LAN DNS profile has been created. Vigor2860 Series User’s Guide...
Page 204: Ii-4-3 Schedule
You can set up to 15 schedules. Then you can apply them to your Internet Access or VPN and Remote Access >> LAN-to-LAN settings. To add a schedule: Click any index, say Index No. 1. The detailed settings of the call schedule with index 1 are shown below. Vigor2860 Series User’s Guide...
Page 205 Click OK button to save the settings. Example Suppose you want to control the PPPoE Internet access connection to be always on (Force On) from 9:00 to 18:00 for whole week. Other time the Internet access connection should be disconnected (Force Down). Vigor2860 Series User’s Guide...
Page 206: Ii-4-4 Radius/Tacacs
RADIUS server. Then LAN user of Vigor router will be authenticated by such server for network application. Available settings are explained as follows: Item Description Enable Check to enable RADIUS client feature. Server IP Address Enter the IP address of RADIUS server Vigor2860 Series User’s Guide...
Page 207: Ii-4-4-2 Internal Radius
Allow to configure that clients under specified domain (IPv4 and IPv6) must be authenticated with the specified shared secret. Enable - Check to enable RADIUS client feature. Shared Secret - The RADIUS server and client share a secret Vigor2860 Series User’s Guide...
Page 208: Ii-4-4-3 External Tacacs
After finished the above settings, click OK button to save the settings. It means Terminal Access Controller Access-Control System Plus. It works like RADIUS does. Click the TACACS+ Setup to open the following page: Available settings are explained as follows: Vigor2860 Series User’s Guide...
Page 209 Both sides must be configured to use the same shared secret. Confirm Shared Secret Re-type the Shared Secret for confirmation. After finished the above settings, click OK button to save the settings. Vigor2860 Series User’s Guide...
Page 210: Ii-4-5 Ldap /Active Directory Setup
Regular Mode– Mostly it is the same with anonymous  mode. The different is that, the server will firstly check if you have the search authority. For the regular mode, you’ll need to type in the Regular DN Vigor2860 Series User’s Guide...
Page 211 After finished the above settings, click OK button to save the settings. You can configure eight AD/LDAP profiles. These profiles would be used with User Management for different purposes in management. Click any index number link to open the following page. Vigor2860 Series User’s Guide...
Page 212 AD/LDAP Server to assist you finish the setup. After finished the above settings, click OK to save and exit this page. A new profile has been created. Vigor2860 Series User’s Guide...
Page 213: Ii-4-6 Upnp
Non-privileged users can control some router functions, including removing and adding port mappings. The UPnP function dynamically adds port mappings on behalf of some UPnP-aware applications. When the applications terminate abnormally, these mappings may not be removed. Vigor2860 Series User’s Guide...
Page 214: Ii-4-7 Igmp
This field displays the ID port for the multicast group. The available range for IGMP starts from 224.0.0.0 to 239.255.255.254. P1 to P6 It indicates the LAN port used for the multicast group. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 215: Ii-4-8 Wake On Lan
MAC Address Type any one of the MAC address of the bound PCs. Wake Up Click this button to wake up the selected IP. See the following figure. The result will be shown on the box. Vigor2860 Series User’s Guide...
Page 216: Ii-4-9 Sms / Mail Alert Service
Schedule (1-15) Type the schedule number that the SMS will be sent out. You can click the Schedule(1-15) link to define the schedule. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 217 Schedule (1-15) Type the schedule number that the notification will be sent out. You can click the Schedule(1-15) link to define the schedule. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 218: Ii-4-10 Bonjour
Below shows an example for applying the bonjour feature that Vigor router can be used as the FTP server. 1. Here, we use Firefox and DNSSD to discover the service in such case. Therefore, just ensure the Bonjour client program and DNSSD for Firefox have been installed on the computer. Vigor2860 Series User’s Guide...
Page 219 5. Open the DNSSD page again. The available items will be changed as the follows. It means the Vigor router (based on Bonjour protocol) is ready to be used as a printer server, FTP server, SSH Server, Telnet Server, and HTTP Server. Vigor2860 Series User’s Guide...
Page 220 6. Now, any page or document can be printed out through Vigor router (installed with a printer). Vigor2860 Series User’s Guide...
Page 221: Application Notes
Create LDAP server profiles. Click the Active Directory /LDAP tab to open the profile web page and click any one of the index number link. If we have two groups “RD1” and “SHRD” on LDAP server, we can configure two LDAP server profiles with different Group Distinguished Name. Vigor2860 Series User’s Guide...
Page 222 Click OK to save the settings above. Open User Management>>General Setup. Select User-Based as the Mode option. Vigor2860 Series User’s Guide...
Page 223 Then open VPN and Remote Access>>PPP General Setup to check the profile(s) that will be authenticated with LDAP server. After above configurations, users belong to either “rd1” or “shrd” group can access Internet after inputting their credentials on LDAP server. Vigor2860 Series User’s Guide...
Page 224: How To Configure Customized Ddns
WAN connection is up. Note that, Username: jo*** Password: jo******** Host name: j*****.changeip.org WAN IP address: 1.169.185.242 Following is the screenshot of editing the HTML script on the browser to update your IP to the DDNS server. Vigor2860 Series User’s Guide...
Page 225 DDNS service is running. In this case the IP will be 1.169.185.242. After setting, the Customized DDNS service will be up, and our IP will be updated to the DDNS server. Username: bi******* Password: 88******** Host name: bi*******.3322.org Vigor2860 Series User’s Guide...
Page 226 Set the Provider Host as member.3322.net. Set the Service API as: /dyndns/update?hostname=yourhost.3322.org&myip=###IP###&wildcard=OFF&mx=mail .exchanger.ext&backmx=NO&offline=NO Enter your account and password. After the setting, the Customized DDNS service will be up, and our IP will be updated to the DDNS server automatically. Vigor2860 Series User’s Guide...
Page 227 The customized Service Provider is also eligible with the ClouDNS.net. Vigor2860 Series User’s Guide...
Page 228: Routing
Other routing Specify routing policy to determine the direction of the data transmission. Info For more detailed information about using policy route, refer to Support >>FAQ/Application Notes on www.draytek.com. Vigor2860 Series User’s Guide...
Page 229: Web User Interface
Displays the destination address of the static route. Status Displays the status of the static route. Set to Factory Default Clear all of the settings and return to factory default settings. Viewing Routing Table Displays the routing table for your reference. Vigor2860 Series User’s Guide...
Page 230 1st subnet (192.168.1.0/24). The second is that those hosts on the internal private subnets (ex. 192.168.10.0/24) can access the Internet via the router, and continuously exchange of IP routing information with different subnets. Vigor2860 Series User’s Guide...
Page 231 Use the drop down list to specify an interface for such static route. Return to Static Route Setup page. Click on another Index Number to add another static route as show below, which regulates all packets destined to 211.100.88.0 will be forwarded to 192.168.1.3. Click OK. Vigor2860 Series User’s Guide...
Page 232 Set to Factory Default Clear all of the settings and return to factory default settings. Viewing IPv6 Routing Displays the routing table for your reference. Table Click any underline of index number to get the following page. Vigor2860 Series User’s Guide...
Page 233 Type the gateway address for this entry. Network Interface Use the drop down list to specify an interface for this static route. When you finish the configuration, please click OK to save and exit this page. Vigor2860 Series User’s Guide...
Page 234: Ii-5-2 Load-Balance /Route Policy
Use Up or Down link to move the order of the policy. Wizard Mode Allow to configure frequently used settings of route policy via three setting pages Advance Mode Allow to configure detailed settings of route policy. Vigor2860 Series User’s Guide...
Page 235 Available settings are explained as follows: Item Description Interface Use the drop down list to choose a WAN or LAN interface or VPN profile. Packets match with the above criteria will be transferred to the interface chosen here. Vigor2860 Series User’s Guide...
Page 236 It determines which mechanism that the router will use to Routing forward the packet to WAN. 5. After choosing the mechanism, click Next to get the summary page for reference. 6. If there is no error, click Finish to complete wizard setting. Vigor2860 Series User’s Guide...
Page 237 To use Advance Mode, do the following steps: 1. Click the Advance Mode radio button. 2. Click Index 1 to access into the following page. Available settings are explained as follows: Item Description Enable Check this box to enable this policy. Vigor2860 Series User’s Guide...
Page 238 Static Route and Route Policy. The greater the value is, the lower the priority is. Default value for route policy is “200” which means it has higher priority than the default route. Vigor2860 Series User’s Guide...
Page 239: Ii-5-2-2 Diagnose
When you finish the configuration, please click OK to save and exit this page. With the analysis done by such page, possible path (static route, routing table or policy route) of the packets sent out of the router can be traced. Vigor2860 Series User’s Guide...
Page 240 If required, click export analysis to export the result as a file. Note that the analysis was based on the current "load-balance/route policy" settings, we do not guarantee it will be 100% the same as the real case. Vigor2860 Series User’s Guide...
Page 241: Application Notes
The web user interface will be revised later. Example 1: In the following figure, a LAN to LAN VPN tunnel is built between DrayTek VPN router (e.g., Vigor2860 series) and the remote router. Firewall Router can receive all of the traffic coming from remote PC which wants to access into Internet;...
Page 242 Table are fixed as “150”. You can adjust the value for such route policy with lower value, e.g., 100 to ensure it will be applied to packets transmission with the highest priority. After finished the above settings, click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 243 To route the packets coming from the Firewall Router back to the remote router, access into the web user interface of the Firewall Router. Then, set “192.168.1.1/24” as the gateway IP address and set “172.16.3.0/24” as the destination IP address. Vigor2860 Series User’s Guide...
Page 244 In the following web page, check Enable; type “192.168.1.10” as Src IP Range; type “213.57.89.100” as the Destination IP for the remote VPN server; and choose VPN as the Interface setting. Click OK to save the settings. Vigor2860 Series User’s Guide...
Page 245: How To Setup Address Mapping
We will take an example to introduce how to make use of this feature. Log into the web user interface of Vigor2860. Open WAN>>Internet Access. For WAN1, choose MPoA/Static or Dynamic IP as the Access Mode. Vigor2860 Series User’s Guide...
Page 246 WAN IP address as 202.211.100.10. Click the WAN IP Alias button to configure the other IP address which is 202.211.100.11. Make sure Join IP NAT Pool is not checked. Click OK to save the settings. Vigor2860 Series User’s Guide...
Page 247 After finished configuration for WAN1, open Load-Balance/Route Policy>>General Setup. Choose Advance Mode. Click Index number 1 and 2 to configure the details. After finished the settings, click OK to save the settings respectively. Vigor2860 Series User’s Guide...
Page 248 Upon completing the above configuration, you have specified the outgoing IP address(es) for some specific computers. Now, you bind some specific computers to some WAN IP alias for outgoing traffic. Vigor2860 Series User’s Guide...
Page 249: How To Setup Load Balance For Packets
Internet. The PC in LAN1 can send the data to the remote PC through the specified WAN1. Access into web user interface of Vigor2860 series. Open Load-Balance/Route Policy>>General Setup. From the following web page, simply click index number #1.
Page 250 203.65.1.35; choose WAN1 as the Interface; click default gateway; do not check Failover to. After finished the above settings, click OK to save the configuration. Now, the packets sent to the remote PC (IP address: 203.65.1.35) will be forced to pass through WAN1. Vigor2860 Series User’s Guide...
Page 251: Lte
SMS from a router to report router status, rebooting router remotely via SMS with taking security into consideration, and so on. This section can guide you to use the SIM card in LTE WAN to perform SMS related operations. Info This function is used for “L” models only. Vigor2860 Series User’s Guide...
Page 252: Web User Interface
Custom. The period of reset is between 1 day and 60 days. You can determine the cycle duration by specifying the days and the hours. Cycle duration: Specify the days to reset the number of  Vigor2860 Series User’s Guide...
Page 253 Today is day XX in the cycle –Specify the day in the cycle  duration as the starting point which Vigor router will reset the number of SMS sent. For example, 3 means the third day of the duration cycle. Vigor2860 Series User’s Guide...
Page 254: Ii-6-2 Sms Inbox
Details If you want to read the full content of the message, click the View link of that message to open the following page. It will change the message into "read" state. Vigor2860 Series User’s Guide...
Page 255 If you want to read the full content of the message of the SMS, click the index link of that SMS to open the following page. It will change all SMS of the message into "read" state. Vigor2860 Series User’s Guide...
Page 256 Message Content - Display the full content of the message. OK - Return to previous page. Delete - Click it to delete all SMS of this message and return to previous page. Next - Click it to see the content of next SMS index. Vigor2860 Series User’s Guide...
Page 257: Ii-6-3 Send Sms
The total number of characters that you can type in this field is 1024. Send Message Click it to send this SMS message to the recipient immediately. View SMS Outbox Cache Display the record of SMS messages sent from the Router. Vigor2860 Series User’s Guide...
Page 258: Ii-6-4 Router Commands
Go to LTE>>Router Commands to get the following page. Available settings are explained as follows: Item Description Reboot on SMS Message Enable with Password / To reboot Vigor router remotely via SMS, please check such box and type the password/PIN number (treated as Vigor2860 Series User’s Guide...
Page 259 SMS. SMS messages per status Display the total number of the type for status response. response Display the total number of SMS required to send the status message which contains the current selected Message Contents. Vigor2860 Series User’s Guide...
Page 260: Ii-6-5 Status
Location Area Code / Cell ID : Signal Signal strength of LTE connection. Active Channel Frequency of LTE connection. Interference with 2.4GHz Whether the current LTE frequency causes interference with 2.4G wireless. If Yes, the interfered 2.4G wireless channels Vigor2860 Series User’s Guide...
Page 261 Whether the SMS service of the LTE SIM card is ready. SMS Loading Whether the received SMS messages in the LTE SIM card have been loaded to the Router. New SMS The number of unread SMS in SMS Inbox. Vigor2860 Series User’s Guide...
Page 262: Part Iii Wireless Lan
Wireless LAN enables high mobility so WLAN users can simultaneously access all LAN facilities just like on a wired LAN as well as Internet access. Vigor2860 Series User’s Guide...
Page 263: Wireless Lan (2.4Ghz/5Ghz)
SSID as identification, located channel etc. Vigor router supports four SSID settings for wireless connections. Each SSID can be defined with different name and download/upload rate for selecting by stations connected to the router wirelessly. Vigor2860 Series User’s Guide...
Page 264 Internet without hassle of the confidential information leakage. For a more flexible deployment, you may add filters of MAC addresses to isolate users’ access from wired LAN. It will display all the stations in your wireless network and the status of their connection. Vigor2860 Series User’s Guide...
Page 265 In some countries, there are restrictions on DFS channels as well. We will implement country code to restrict uncertified channels. WPS (Wi-Fi Protected Setup) provides easy procedure to make network connection between wireless station and wireless access point (vigor router) with the encryption of WPA and WPA2. Vigor2860 Series User’s Guide...
Page 266: Web User Interface
2. The screen of wireless wizard will be shown as follows. This page will be used for internal users in a company or your home. Besides, the settings will change based on different model of Vigor2860 series. In this case, Vigor2860ac is used as an example. Available settings are explained as follows:...
Page 267 Exit the wireless wizard without saving any changes. 3. After typing the required information, click Next. The settings in the page limit the wireless station (guest) accessing into Internet but not being allowed to share the LAN network and VPN connection. Vigor2860 Series User’s Guide...
Page 268 The wireless mode offered by this wizard is WPA2/PSK. The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via Vigor2860 Series User’s Guide...
Page 269 Exit the wireless wizard without saving any changes. 4. After typing the required information, click Next. 5. The following page will display the configuration summary for wireless setting. 6. Click Finish to complete the wireless settings configuration. Vigor2860 Series User’s Guide...
Page 270: Iii-1-2 General Setup
Mixed (11b+11g+11n) stations simultaneously. Simply choose Mixed (11b+11g+11n) mode. For 5GHz: At present, the router can connect to 11a Only, 11n Only(5 GHz), Mixed (11a+11n), and Mixed (11a+11n+11ac) stations simultaneously. Simply choose Mixed (11a+11n+11ac) mode. Vigor2860 Series User’s Guide...
Page 271 You may choose up to 4 schedules out of the 15 schedules pre-defined in Applications >> Schedule setup. The default setting of this field is blank and the function will always work. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 272: Iii-1-3 Security
By clicking the Wireless LAN>>Security Settings, a new web page will appear so that you could configure the settings of WPA and WEP. Available settings are explained as follows: Item Description There are several modes provided for you to choose. Mode Vigor2860 Series User’s Guide...
Page 273 12345 (or 10 hexadecimal digitals leading by 0x, such as 0x4142434445.) 128-Bit - For 128 bits WEP key, either 13 ASCII characters, such as ABCDEFGHIJKLM (or 26 hexadecimal digits leading by 0x, such as 0x4142434445464748494A4B4C4D). Vigor2860 Series User’s Guide...
Page 274: Iii-1-4 Access Control
SSID 1 and SSID 2 at the same time if you check SSID 1 and SSID 2. MAC Address Filter Display all MAC addresses that are edited before. Client’s MAC Address Manually enter the MAC address of wireless client. Vigor2860 Series User’s Guide...
Page 275: Iii-1-5 Wps
He/she only needs to press a button on wireless client, and WPS will connect for client and router automatically. There are two methods to do network connection through WPS between AP and Stations: pressing the Start PBC button or using PIN Code. Vigor2860 Series User’s Guide...
Page 276 For WPS is supported in WPA-PSK or WPA2-PSK mode, if you do not choose such mode in Wireless LAN>>Security, you will see the following message box. Please click OK and go back Wireless LAN>>Security to choose WPA-PSK or WPA2-PSK mode and access WPS again. Vigor2860 Series User’s Guide...
Page 277 Start PIN button. The WPS LED on the router will blink fast when WPS is in progress. It will return to normal condition after two minutes. (You need to setup WPS within two minutes) Vigor2860 Series User’s Guide...
Page 278: Iii-1-6 Wds
In the following examples, hosts connected to Bridge 1 or 3 can communicate with hosts connected to Bridge 2 through WDS links. However, hosts connected to Bridge 1 CANNOT communicate with hosts connected to Bridge 3 through Bridge 2. Vigor2860 Series User’s Guide...
Page 279 Available settings are explained as follows: Item Description Mode Choose the mode for WDS setting. Disable mode will not invoke any WDS setting. Bridge mode is designed to fulfill the first type of application. Repeater mode is for the second one. Vigor2860 Series User’s Guide...
Page 280 Disable to cancel this function. Status It allows user to send “hello” message to peers. Yet, it is valid only when the peer also supports this function. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 281: Iii-1-7 Advanced Setting
802.11g or 802.11b wireless client is connected. Green Field – to get the highest throughput, please choose such mode. Such mode can make the data transmission happen between 11n systems only. In addition, it does not Vigor2860 Series User’s Guide...
Page 282 Note: Vigor N61 wireless adapter supports this function. Therefore, you can use and install it into your PC for matching with Packet-OVERDRIVE (refer to the following picture of Vigor N61 wireless utility window, choose Enable for TxBURST on the tab of Option). Vigor2860 Series User’s Guide...
Page 283 It allows devices to take more time in sleeping state and consume less power to improve the performance by minimizing transmission latency. The default setting is Disable. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 284: Iii-1-8 Station Control
SSID will be listed on Station Control List. WEB Portal Setup Click it to access in to LAN>>Web Portal Setup page for modifying the settings if required. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 285: Iii-1-9 Ap Discovery
AP’s MAC address on the bottom of the page and click Bridge or Repeater. Next, click Add to. Later, the MAC address of the AP will be added to Bridge or Repeater field of WDS settings page. Vigor2860 Series User’s Guide...
Page 286: Iii-1-10 Station List
WLAN station and click Add to Access Control below. Available settings are explained as follows: Item Description Refresh Click this button to refresh the status of station list. Click this button to add current typed MAC address into Access Control. Vigor2860 Series User’s Guide...
Page 287: Part Iv Voip
Voice over IP network (VoIP) enables you to use your broadband Internet connection to make toll quality voice calls over the Internet. Vigor2860 Series User’s Guide...
Page 288 Then, both parties’ SIP proxies will forward the sequence of messages to caller to establish the session. If you both register to the same SIP Registrar, then it will be illustrated as below: Vigor2860 Series User’s Guide...
Page 289 Internet. You will always have the required inbound and outbound bandwidth that is prioritized exclusively for Voice traffic over Internet but you just get your data a little slower and it is tolerable for data traffic. Vigor2860 Series User’s Guide...
Page 290: Voip
ISP which offers the VoIP service for your router. SIP Port – Use the default setting (5060). Set Account quickly Account Number/Name – Type the account number/name registered to your ISP. Password – Type the password for the account registered to your ISP. Vigor2860 Series User’s Guide...
Page 291 Click it to get into the next setting page. Cancel Click it to give up the VoIP wizard. 3. After finished the settings above, click Next for viewing summary of such connection. 4. Click Finish. A page of VoIP Wizard Setup OK!!! will appear. Vigor2860 Series User’s Guide...
Page 292: Vi-1-2 Dialplan
1. After the connection established, vigor router A will NOT send SAS voice prompt to vigor router A and vigor router B will NOT send the SAS voice prompt to vigor router B. 2. Even no voice prompt, but the RTP traffic is still secured until the call ends. Vigor2860 Series User’s Guide...
Page 293: Vi-1-1-1 Phone Book
“speed-dial” Phone Number. There are total 60 index entries in the phonebook for you to store all your friends and family members’ SIP addresses. Loop through and Backup Phone Number will be displayed if you are using Vigor2860 series for setting the phone book.
Page 294 If the incoming or outgoing calls do not match any entry on the phonebook, the router will try to make the call "being protected". But, if the call ends up "unprotected"(e.g. peer side does not support ZRTP+SRTP), the router will not play out a warning message. Vigor2860 Series User’s Guide...
Page 295: Vi-1-1-2 Digit Map
VoIP interface. Take the above picture (Prefix Table Setup web page) as an example, the prefix number of 03 will be replaced by 8863. For example: dial number of “031111111” will be changed to “88631111111” and sent to Vigor2860 Series User’s Guide...
Page 296: Vi-1-1-3 Call Barring
Click the link to move the selected entry up or down. After finishing all the settings here, please click OK to save the configuration. Call barring is used to block phone calls coming from the one that is not welcomed. Vigor2860 Series User’s Guide...
Page 297 Unknown Domain or Block IP Address. Simply click the relational links to open the web page. For Block Anonymous – this function can block the incoming calls without caller ID on the interface (Phone port) specified in the following window. Such control also can be done based on preconfigured schedules. Vigor2860 Series User’s Guide...
Page 298 SIP accounts. Such control also can be done based on preconfigured schedules. For Block IP Address – this function can block incoming calls (through Phone port) coming from IP address. Such control also can be done based on preconfigured schedules. Vigor2860 Series User’s Guide...
Page 299: Vi-1-1-4 Regional
Dial the number typed in this field to forward all the Ans][Act] incoming calls to the specified place while there is no answer of the connected phone. Do Not Disturb [Act] Dial the number typed in this field to invoke the function of DND. Vigor2860 Series User’s Guide...
Page 300: Vi-1-1-5 Pstn Setup
PSTN number available for dial whenever you need and type the number in the field of phone number for PSTN relay. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 301: Vi-1-3 Sip Accounts
Click this link to access into next page for setting SIP account. Profile Display the profile name of the account. Domain/Realm Display the domain name or IP address of the SIP registrar server. Proxy Display the domain name or IP address of the SIP proxy Vigor2860 Series User’s Guide...
Page 302 For example, if the domain name is draytel.org, then you might set draytel-1 in this field. Register via If you want to make VoIP call without register personal information, please choose None and check the box to Vigor2860 Series User’s Guide...
Page 303 Stun – Choose this option if there is Stun server provided for your router. Manual – Choose this option if you want to specify an external IP address as the NAT transversal support. Nortel – If the soft-switch that you use supports Nortel Vigor2860 Series User’s Guide...
Page 304 Single Codec – If the box is checked, only the selected Codec will be applied. Packet Size The amount of data contained in a single packet. The default value is 20 ms, which means the data packet will contain 20 ms voice information. Vigor2860 Series User’s Guide...
Page 305 If not, the router will do something to save the bandwidth for other using. Click On to invoke this function; click off to close the function. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 306: Vi-1-4 Phone Settings
Dynamic RTP Port End - Specifies the end port for RTP stream. The default value is 15000. RTP TOS – It decides the level of VoIP package. Use the drop down list to choose any one of them. Vigor2860 Series User’s Guide...
Page 307 Check the box to enable the function. In the limited time that you set in this field, if there is no response, the connecting call will be closed automatically. T.38 Fax Function Check the box to enable T.38 fax function. Vigor2860 Series User’s Guide...
Page 308 ID type automatically. Or you can adjust tone settings manually if you choose User Defined. TOn1, TOff1, TOn2 and TOff2 mean the cadence of the tone pattern. TOn1 and TOn2 represent sound-on; TOff1 and TOff2 represent the sound-off. Vigor2860 Series User’s Guide...
Page 309 Congestion tone will be shown automatically on the page. If you cannot find out a suitable one, please choose User Defined and fill out the corresponding values for dial tone, ringing tone, busy tone, congestion tone by yourself for VoIP phone. Vigor2860 Series User’s Guide...
Page 310 This function is very useful when the network traffic congestion occurs and it still can remain the accuracy of DTMF tone. Vigor2860 Series User’s Guide...
Page 311: Vi-1-5 Status
CONNECTING - Indicates that the user is calling out. WAIT_ANS - Indicates that a connection is launched and waiting for remote user’s answer. ALERTING - Indicates that a call is coming. ACTIVE-Indicates that the VoIP connection is launched. Vigor2860 Series User’s Guide...
Page 312 Accumulation for the times of in call. Out Calls Accumulation for the times of out call. Miss Calls Accumulation for the times of missing call. Speaker Gain The volume of present call. Display logs of VoIP calls. Vigor2860 Series User’s Guide...
Page 313: Part V Vpn
Here Vigor router support digital certificates conforming to standard X.509. Vigor2860 Series User’s Guide...
Page 314: Vpn And Remote Access
The VPN built is suitable for: Communication between home office and customer   Secure connection between Teleworker, staff on business trip and main office Exchange data between remote office and main office  POS between chain store and headquarters  Vigor2860 Series User’s Guide...
Page 315: Web User Interface
Route Mode/NAT Mode – If the remote network only allows you to dial in with single IP, please choose NAT mode, otherwise please choose Route Mode. Please choose a There are 32 VPN profiles for users to set. LAN-to-LAN Profile Vigor2860 Series User’s Guide...
Page 316 Info The following descriptions for VPN Type are based on the Route Mode specified in LAN-to-LAN Client Mode Selection. When you choose PPTP (None Encryption) or PPTP (Encryption), you will see the following graphic: Vigor2860 Series User’s Guide...
Page 317 When you choose IPsec, you will see the following graphic: When you choose SSL, you will see the following graphic: When you choose L2TP over IPsec (Nice to Have) or L2TP over IPsec (Must), you will see the following graphic: Vigor2860 Series User’s Guide...
Page 318 Type a name for such profile. The length of the file is limited to 10 characters. VPN Dial-Out Through Use the drop down menu to choose a proper WAN interface for this profile. This setting is useful for dial-out only. Vigor2860 Series User’s Guide...
Page 319 By default, this option is active. High - Encapsulating Security Payload (ESP) means payload (data) will be encrypted and authenticated. You may select encryption algorithm from Data Encryption Standard (DES), Triple DES (3DES), and AES. Vigor2860 Series User’s Guide...
Page 320 Click this radio button to set another profile of VPN Server Server Wizard Setup through VPN Server Wizard. View more detailed Click this radio button to access VPN and Remote configuration Access>>LAN to LAN for viewing detailed configuration. Vigor2860 Series User’s Guide...
Page 321: V-1-2 Vpn Server Wizard
This item is available after you choose any one of dial-in user account profiles. Next, you have to select suitable dial-in type for the VPN server profile. There are several types provided here (similar to VPN Client Wizard). Vigor2860 Series User’s Guide...
Page 322 When you check PPTP/SSL, you will see the following graphic: When you check PPTP & IPsec & L2TP (three types) or PPTP & IPsec (two types) or L2TP with Policy (Nice to Have/Must), you will see the following graphic: Vigor2860 Series User’s Guide...
Page 323 The length of the name is limited to 11 characters. Password This field is used to authenticate for connection when you select PPTP or L2TP with or without IPsec policy above. The length of the name is limited to 11 characters. Vigor2860 Series User’s Guide...
Page 324 Go to the VPN Click this radio button to access VPN and Remote Connection Access>>Connection Management for viewing VPN Management Connection status. Do another VPN Click this radio button to set another profile of VPN Server Vigor2860 Series User’s Guide...
Page 325: V-1-3 Remote Access Control
LAN, you should disable the VPN service of Vigor Router to allow VPN tunnel pass through, as well as the appropriate NAT settings, such as DMZ or open port. Open VPN and Remote Access>>Remote Access Control. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 326: V-1-4 Ppp General Setup
 Maximum MPPE - This option indicates that the router will use the MPPE encryption scheme with maximum bits (128-bit) to encrypt the data. Mutual Authentication The Mutual Authentication function is mainly used to Vigor2860 Series User’s Guide...
Page 327 While using Radius or If PPP connection will be authenticated via RADIUS server or LDAP Authentication LDAP profiles, it is necessary to specify the LAN profile for the dial-in user to get IP from. Vigor2860 Series User’s Guide...
Page 328: V-1-5 Ipsec General Setup
(LAN-to-LAN) which uses dynamic IP address and IPsec-related VPN connections such as L2TP over IPsec and IPsec tunnel. There are two methods offered by Vigor router for you to authenticate the incoming data coming from remote dial-in user, Certificate (X.509) and Pre-Shared Vigor2860 Series User’s Guide...
Page 329: V-1-6 Ipsec Peer Identity
32 entries of digital certificates for peer dial-in users. Available settings are explained as follows: Item Description Set to Factory Default Click it to clear all indexes. Index Click the number below Index to access into the setting page Vigor2860 Series User’s Guide...
Page 330 The field includes Country (C), State (ST), Location (L), Organization (O), Organization Unit (OU), Common Name (CN), and Email (E). After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 331: V-1-7 Remote Dial-In User
Click each index to edit one remote user profile. Each Dial-In Type requires you to fill the different corresponding fields on the right. If the fields gray out, it means you may leave it untouched. The following explanation will guide you to fill all the necessary fields. Vigor2860 Series User’s Guide...
Page 332 Specify Remote Node -You can specify the IP address of the remote dial-in user, ISDN number or peer ID (used in IKE aggressive mode). Uncheck the checkbox means the connection type you select above will apply the authentication methods and security Vigor2860 Series User’s Guide...
Page 333 Triple DES (3DES), and AES. Local ID (Optional)- Specify a local ID to be used for Dial-in setting in the LAN-to-LAN Profile setup. This item is optional and can be used only in IKE aggressive mode. Vigor2860 Series User’s Guide...
Page 334: V-1-8 Lan To Lan
The router supports up to 32 VPN tunnels simultaneously. The following figure shows the summary table. The following figure shows the summary table according to the item (All/Trunk) selected for View. The following shows profiles joined into VPN Load Balance and VPN Backup mechanism. Vigor2860 Series User’s Guide...
Page 335 Click each index to edit each profile and you will get the following page. Each LAN-to-LAN profile includes 4 subgroups. If the fields gray out, it means you may leave it untouched. The following explanations will guide you to fill all the necessary fields. Vigor2860 Series User’s Guide...
Page 336 WAN1 Only: Only establish VPN if WAN2 down - If WAN2 failed, the router will use WAN1 for VPN connection. WAN2 Only: Only establish VPN if WAN1 down - If  WAN1 failed, the router will use WAN2 for VPN Vigor2860 Series User’s Guide...
Page 337 L2TP with IPsec Policy - Build a L2TP VPN connection through the Internet. You can select to use L2TP alone or with IPsec. Select from below: None: Do not apply the IPsec policy. Accordingly, the  Vigor2860 Series User’s Guide...
Page 338 MD5 or SHA-1 authentication algorithm.  3DES without Authentication-Use triple DES encryption algorithm and not apply any authentication scheme.  3DES with Authentication-Use triple DES encryption algorithm and apply MD5 or SHA-1 authentication algorithm.  AES without Authentication-Use AES encryption Vigor2860 Series User’s Guide...
Page 339 Index(1-15) - Set the wireless LAN to work at certain time interval only. You may choose up to 4 schedules out of the 15 schedules pre-defined in Applications >> Schedule setup. The default setting of this field is blank and the function will always work. Vigor2860 Series User’s Guide...
Page 340 VPN connection becomes one pure L2TP connection. Must - Specify the IPsec policy to be definitely  applied on the L2TP connection. SSL Tunnel- Allow the remote dial-in user to trigger an  SSL VPN connection through Internet. Vigor2860 Series User’s Guide...
Page 341 IPsec packet after configuring IPsec Dial-Out setting. Both ends must match for each other by setting same virtual IP address for communication. Logical Traffic: Such technique comes from RFC2890. Define logical traffic for data transmission between both sides of Vigor2860 Series User’s Guide...
Page 342 VPN connection. This is usually used when you find there are several subnets behind the remote VPN router. RIP Direction - The option specifies the direction of RIP (Routing Information Protocol) packets. You can Vigor2860 Series User’s Guide...
Page 343 Remote Network IP Addresses/ Remote Network Mask through the VPN connection. This is usually used when you find there are several subnets behind the remote VPN router. Translated Type – There are two types for you to choose. Vigor2860 Series User’s Guide...
Page 344 Virtual IP Mapping – A pop up dialog will appear for you to specify the local IP address and the mapping virtual IP address. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 345: V-1-9 Vpn Trunk Management
The TCP Session transmitted by using VPN TRUNK-VPN Load Balance mechanism will not be lost due to one of VPN Tunnels disconnected. Users do not need to reconnect with setting TCP/UDP Service Port again. The VPN Load Balance function can keep the transmission for internal data on tunnel stably Vigor2860 Series User’s Guide...
Page 346 IPsec, PPTP, L2TP, L2TP over IPsec (NICE), L2TP over IPsec(MUST) and so on. Member2 - Display the dial-out profile selected from the Member2 drop down list below. Advanced – This button is available only when LAN to LAN profile (or more) is created. Vigor2860 Series User’s Guide...
Page 347 Member2 drop down list below. Advanced – This button is only available when there is one or more profiles created in this page. Detailed information for this dialog, see later section - Advanced Load Balance and Backup. Vigor2860 Series User’s Guide...
Page 348 For there is one Tunnel created and connected successfully, to keep the load balance effect between two tunnels, auto-dial will be executed within two seconds. To close two tunnels of load balance after connecting, please click Disable for Status in General Setup field. Vigor2860 Series User’s Guide...
Page 349 If the router will be used as the VPN Server (i.e., with virtual address 192.168.50.200). Please type 192.168.50.200 in the field of My GRE IP. Type IP address (192.168.50.100) of the client in the field of Peer GRE IP. See the following graphic for an example. Vigor2860 Series User’s Guide...
Page 350 IP address of the server (192.168.50.200) in the field of Peer GRE IP. After setting profiles for load balance, you can choose any one of them and click Advance for more detailed configuration. The windows for advanced load balance and backup are different. Refer to the following explanation: Vigor2860 Series User’s Guide...
Page 351 Below shows the algorithm for Load Balance. Edit – Click this radio button for assign a blank table for configuring Binding Tunnel. Insert after – Click this radio button to adding a new binding tunnel table. Vigor2860 Series User’s Guide...
Page 352 TCP Service Port/UDP Service Port/ICMP/IGMP, such binding tunnel table can be established. Detail Information This field will display detailed information for Binding Tunnel Policy. Below shows a successful binding tunnel policy for load balance: Vigor2860 Series User’s Guide...
Page 353 Binding Protocol. Available settings are explained as follows: Item Description Profile Name List the backup profile name. ERD Mode ERD means “Environment Recovers Detection”. Normal – choose this mode to make all dial-out VPN TRUNK Vigor2860 Series User’s Guide...
Page 354: V-1-10 Connection Management
VPN backup function. Backup Mode - This filed displays the profile name saved in VPN TRUNK Management (with Index number and VPN Server IP address). The VPN connection built by Backup Mode supports VPN backup function. Vigor2860 Series User’s Guide...
Page 355 Dial - Click this button to execute dial out function. Refresh Seconds - Choose the time for refresh the dial information among 5, 10, and 30. Refresh - Click this button to refresh the whole connection status. Vigor2860 Series User’s Guide...
Page 356: Application Notes
(in this case, type VPN Server), and check the box of Enable This Profile. For Vigor router will be set as a server, the call direction shall be set as Dial-in and set 0 as Idle Timeout. Vigor2860 Series User’s Guide...
Page 357 Continue to navigate to the TCP/IP Network Settings for setting the LAN IP for remote side. Click OK to save the settings. Open VPN and Remote Access>>Connection Management to check the dial-in connection status (from branch office). Vigor2860 Series User’s Guide...
Page 358 (in this case, type VPN Client), and check the box of Enable This Profile. For such Vigor router will be set as a client, the call direction shall be set as Dial-out. Check the box of Always on for a permanent VPN connection. Vigor2860 Series User’s Guide...
Page 359 IKE Pre-Shared Key button to set the PSK; and select Medium (AH) or High (ESP) as the security method. Continue to navigate to the TCP/IP Network Settings for setting the LAN IP for the remote side. Click OK to save the settings. Vigor2860 Series User’s Guide...
Page 360 Open VPN and Remote Access>>Connection Management to check the dial-in connection status (from head office). Vigor2860 Series User’s Guide...
Page 361: Ssl Vpn
There are two benefits that SSL VPN provides:  It is not necessary for users to preinstall VPN client software for executing SSL VPN connection.  There are less restrictions for the data encrypted through SSL VPN in comparing with traditional VPN. Vigor2860 Series User’s Guide...
Page 362: Web User Interface
Self-signed to use the router’s built-in default certificate. The default certificate can be used in SSL VPN server and HTTPS Web Proxy. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 363: V-2-2 Ssl Web Proxy
Type the address (function variation or IP address) or path of the proxy server. Host IP Address If you type function variation as URL, you have to type corresponding IP address in this filed. Such field must match with URL setting. Vigor2860 Series User’s Guide...
Page 364 In addition, users must execute “Connect” manually in SSL Client Portal page. SSL – if you choose such selection, web proxy over SSL will be applied for VPN. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 365: V-2-3 Ssl Application
To create a new SSL application profile: 1. Click number link under Index filed to set detailed configuration. 2. The following page will appear. Available settings are explained as follows: Item Description Enable Application Check the box to enable such profile. Vigor2860 Series User’s Guide...
Page 366 Screen Size such application. If you choose SMB, you have to specify the path of the SMB SMB Path service. 3. Enter the required information. 4. After finished the above settings, click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 367: V-2-4 User Account
With SSL VPN, Vigor2860 series let teleworkers have convenient and simple remote access to central site VPN. The teleworkers do not need to install any VPN software manually. From regular web browser, you can establish VPN connection back to your main office even in a guest network or web cafe.
Page 368 Internet. You should set the User Name and Password of remote dial-in user below. IPSec Tunnel - Allow the remote dial-in user to make an IPSec VPN connection through Internet. L2TP with IPSec Policy - Allow the remote dial-in user to Vigor2860 Series User’s Guide...
Page 369 IPSec Security Method This group of fields is a must for IPSec Tunnels and L2TP with IPSec Policy when you specify the remote node. Check the Medium, DES, 3DES or AES box as the security method. Vigor2860 Series User’s Guide...
Page 370 Local ID - Specify a local ID to be used for Dial-in setting in the LAN-to-LAN Profile setup. This item is optional and can be used only in IKE aggressive mode. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 371: V-2-5 User Group
Click to clear all indexes. Index Display the number of the client which connecting to FTP server. Name Display the name of the group profile. Click any index number link to open the following page for detailed configuration. Vigor2860 Series User’s Guide...
Page 372 If the above three options are enabled, the system will do the authentication based on them in sequence. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 373: V-2-6 Online User Status
If you have finished the configuration of SSL Web Proxy (server), users can find out corresponding settings when they access into DrayTek SSL VPN portal interface. Next, users can open SSL VPN>> Online Status to view logging status of SSL VPN.
Page 374: Certificate Management
Here you can manage generate and manage the local digital certificates, and set trusted CA certificates. Remember to adjust the time of Vigor router before using the certificate so that you can get the correct valid period of certificate. Below shows the menu items for Certificate Management. Vigor2860 Series User’s Guide...
Page 375: Web User Interface
Click this button to open Generate Certificate Signing Request window. Type in all the information that the window request such as certifcate name (used for identifying different certificate), subject alternative name type and relational settings for subject name. Then click GENERATE again. Vigor2860 Series User’s Guide...
Page 376 The supported types are PKCS12 Certificate and Certificate with a private key. Click this button to import a saved file as the certification information. There are three types of local certificate supported by Vigor router. Vigor2860 Series User’s Guide...
Page 377 Netscape and Microsoft Internet Explorer with their import and export options. Upload Certificate and It is useful when users have separated certificates and private Private Key keys. And the password is needed if the private key is encrypted. Vigor2860 Series User’s Guide...
Page 378 Next, access your CA server and enter the page of certificate request, copy the information into it and submit a request. A new certificate will be issued to you by the CA server. You can save it. Click this button to remove the selected certificate. Vigor2860 Series User’s Guide...
Page 379: V-3-2 Trusted Ca Certificate
Therefore, Vigor router offers a mechanism which allows you to generate root CA to save time and provide convenience for general user. Later, such root CA generated by DrayTek server can perform the issuing of local certificate. Info Root CA can be deleted but not edited.
Page 380 Trusted CA Certificate window. For viewing each trusted CA certificate, click View to open the certificate detail information window. If you want to delete a CA certificate, choose the one and click Delete to remove all the certificate information. Vigor2860 Series User’s Guide...
Page 381: V-3-3 Certificate Backup
Please click Backup on the following screen to save them. If you want to set encryption password for these certificates, please type characters in both fields of Encrypt password and Confirm password. Also, you can use Restore to retrieve these two settings to the router whenever you want. Vigor2860 Series User’s Guide...
Page 382: Central Vpn Management
Vigor2860 can build virtual private network (VPN) between itself and any other TR-069 CPE by the function of central VPN management. In addition, it can be treated as a server (called CVM server) which can manage TR-069 CPE for periodical firmware upgrade, configuration backup and restoring configuration. Vigor2860 Series User’s Guide...
Page 383: Web User Interface
Type the port number in the box. WAN IP for Remote For Vigor router can manage only the client from WAN Connection interface, therefore you have to specify which interface will be used for such function. If you choose MANUALLY, you have Vigor2860 Series User’s Guide...
Page 384: V-4-1-2 Ipsec Vpn Settings
Encryption Type Choose one of the selections as the encryption type. Local Subnet Type the IP address and subnet mask of local host. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 385: V-4-2-1 Managed Device List
All the CPEs managed by Vigor2860 series can be seen with icons from this page. Before using such feature, make sure the CVM port has been enabled and configured properly. This page allows you to manage the CPEs connected to Vigor2860 series.
Page 386 Delete – To disconnect the management of any CPE, click the CPE icon you want and click the Delete button. Double-clicking the CPE icon also can pop up the Managed Device Detail window. However, you cannot modify any data on the window. Vigor2860 Series User’s Guide...
Page 387: V-4-2 Cpe Management
Only eight remote devices can be managed by Vigor2860 at one time. Therefore, other remote devices detected by Vigor2860 series might not be displayed in such field. Add – Move the selected device from Unmanaged Devices List to Managed Devices List.
Page 388: V-4-2-2 Cpe Maintenance
Index Display the number of the profile that you can edit. Profile Name Display the name of the maintenance profile. Device Name Display the name of the managed CPE that the maintenance profile will apply to. Vigor2860 Series User’s Guide...
Page 389 Check it to enable such profile. Device Name The drop down list will display all the CPE devices detected by Vigor2860 series. Choose the one which will be applied with such new created profile. Action Type There are three actions for you to choose for such profile.
Page 390: V-4-2-3 Google Map
Click Select to locate the file you want to save, restore or upgrade for CPE. Index in Schedule Vigor2860 series will perform the specified action to the selected CPE based on the schedule configured here. Specify one or two schedule profiles (represented by number) here.
Page 391: V-4-3 Vpn Management
UP Time Display the connection time of such VPN. Once the device is managed (controlled) by Vigor2860 series, it will be displayed on such screen automatically. If not, refer to sections “How to manage the CPE (router) through Vigor2860?” for more detailed information.
Page 392: V-4-4 Log & Alert
Vigor2860 series. Action Type Display the action that Vigor2860 series will perform for the managed CPE. Message Display the information for each event. The Alert page offers brief information to identify the CPE connected to Vigor2860 series. Vigor2860 Series User’s Guide...
Page 393: Application Notes
To manage CPEs through Vigor2860 series, you have to set URL on CPE first and set username and password for Vigor2860 series. For this section, we use Vigor2850 series as the example. All the CPE configuration will be done through Vigor2850 series.
Page 394 In the field of ACS Server, type the URL (IP address with port number) of Vigor2860 series and type the same Username and Password defined on the page of Central VPN Management>>General Setup in Vigor2860 series. Then, click Enable for CPE Client and then click OK to save the settings.
Page 395 Open WAN>>Internet Access. Use the drop down list of Access Mode on WAN1 to select MPoA (RFC1483/2684). Then, click Details Page. Click Specify an IP address. Type correct WAN IP address, subnet mask and gateway IP address for your CPE. Then click OK. Vigor2860 Series User’s Guide...
Page 396 Info Reboot the CPE device and re-log into Vigor2860 series. CPE which has registered to Vigor2860 series will be captured and displayed on the page of Central VPN Management>>CPE Management. Return to the web user interface of Vigor2860 series. Open Central VPN Management>>VPN Management. Now there is one CPE displayed on the field of Unmanaged Devices List.
Page 397: Series
When a remote device is managed by Vigor2860 series, it is easy to build VPN between these two devices. Access into the web user interface of Vigor2860 series. Open Central VPN Management>>CPE Management. Click the device icon (marked with ) and click the PPTP/IPsec button.
Page 398 VPN and Remote Access>>LAN to LAN of the remote device for viewing the detailed information. Note: The profile name is created automatically by the system. Do not modify any value in such page to avoid VPN error. Vigor2860 Series User’s Guide...
Page 399: Cvm Application - How To Upgrade Cpe Firmware Through Vigor2860 Series
Vigor2850, as an example, is chosen for Vigor2860 to perform the CPE firmware upgrade remotely in this case. Plug in USB storage disk onto Vigor2860 series via USB interface. Make sure the USB disk has been installed correctly, otherwise, the firmware upgrade will not be successful.
Page 400 Select to locate it. Specify the Schedule profile. At last, click OK. Now, a new maintenance profile has been created. Click Now to perform the firmware upgrade immediately for Vigor2850. Wait for several minutes for firmware upgrade. Vigor2860 Series User’s Guide...
Page 401 Click Managed Devices List. Click the icon of Vigor2850 and click Edit and view the software version. Another way to check if the firmware upgrade is completed or not, simply open Central VPN Management>>Log & Alert. Vigor2860 Series User’s Guide...
Page 402: Part Vi Security
It also restricts users in the local network from accessing the Internet. CSM is an abbreviation of Central Security Management which is used to control IM/P2P usage, filter the web content and URL content to reach a goal of security management. Vigor2860 Series User’s Guide...
Page 403: Firewall
It will check packets according to the filter rules. If legal, the packet will pass the router. The following illustrations are flow charts explaining how router will treat incoming traffic and outgoing traffic respectively. Vigor2860 Series User’s Guide...
Page 404 3. ICMP flood attack 11. TCP flag scan 4. Port Scan attack 12. Tear drop attack 5. IP options 13. Ping of Death attack 6. Land attack 14. ICMP fragment 7. Smurf attack 15. Unassigned Numbers 8. Trace route Vigor2860 Series User’s Guide...
Page 405: Web User Interface
Click Firewall and click General Setup to open the general setup page. Such page allows you to enable / disable Call Filter and Data Filter, determine general rule for filtering the incoming and outgoing data. Available settings are explained as follows: Item Description Vigor2860 Series User’s Guide...
Page 406 IPv4 - To prevent remote client accessing into the PCs on LAN, check the box to make the incoming packets via IPv4 being blocked by such router. It is effective only for the packets routed but not for packets translated by NAT. Vigor2860 Series User’s Guide...
Page 407 For detailed information of setting QoS, please refer to the related section later. User Management Such item is available only when Rule-Based is selected in User Management>>General Setup. The general firewall rule will be applied to the user/user group/all users specified here. Vigor2860 Series User’s Guide...
Page 408 CSM>> Web Content Filter web page first. Or click the DNS Filter link in this page to create a new profile. Advance Setting Click Edit to open the following window. However, it is strongly recommended to use the default settings here. Vigor2860 Series User’s Guide...
Page 409 However, if the network is not stable, small value will be proper. Session timeout – Setting timeout for sessions can make the best utilization of network resources. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 410: Vi-1-2 Filter Setup
Set the link to the next filter set to be executed after the current filter run. Do not make a loop with many filter sets. To edit Filter Rule, click the Filter Rule index button to enter the Filter Rule setup page. Vigor2860 Series User’s Guide...
Page 411 Call Filter, this setting is not available since Call Filter is only applied to outgoing traffic. Note: RT means routing domain for 2nd subnet or other LAN. Source/Destination IP Click Edit to access into the following dialog to choose the source/destination IP or IP ranges. Vigor2860 Series User’s Guide...
Page 412 Service Type and type them in this dialog. In addition, if you want to use the service type from defined groups or objects, please choose Group and Objects as the Service Type. Protocol - Specify the protocol(s) which this filter rule will Vigor2860 Series User’s Guide...
Page 413 No-Strict - no limitation. Quality of Service Choose one of the QoS rules to be applied as firewall rule. For detailed information of setting QoS, please refer to the related section later. Vigor2860 Series User’s Guide...
Page 414 CSM>> Web Content Filter web page first. Or click the DNS Filter link from the drop down list in this page to create a new profile. Advance Setting Click Edit to open the following window. However, it is Vigor2860 Series User’s Guide...
Page 415 TCP protocol only; session timeout is configured for the data flow which matched with the firewall rule. DrayTek Banner – Please uncheck this box and the following screen will not be shown for the unreachable web page. The default setting is Enabled.
Page 416 Each filter set is composed by 7 filter rules, which can be further defined. After that, in General Setup you may specify one set for call filter and one set for data filter to execute first. Vigor2860 Series User’s Guide...
Page 417: Vi-1-3 Dos Defense
Once detecting the Threshold of the UDP packets from the Internet has exceeded the defined value, the Vigor router will start to randomly discard the subsequent UDP packets for a period defined in Timeout. The default setting for threshold and timeout are 2000 Vigor2860 Series User’s Guide...
Page 418 Activating the DoS/DDoS defense functionality might block some legal packets. For example, when you activate the fraggle attack defense, all broadcast UDP packets coming from the Internet are blocked. Therefore, the RIP packets from the Internet might be dropped. Vigor2860 Series User’s Guide...
Page 419 All the warning messages related to DoS Defense will be sent to user and user can review it through Syslog daemon. Look for the keyword DoS in the message, followed by a name to indicate what kind of attacks is detected. Vigor2860 Series User’s Guide...
Page 420 Vigor2860 Series User’s Guide...
Page 421: Application Notes
Firewall>>Filter Setup is used as the default setting, we have to create a new rule starting from Filter Rule 2 of Set 2. Access into the web user interface of Vigor router. Open Firewall>>Filter Setup. Click the Set 2 link and choose the Filter Rule 2 button. Vigor2860 Series User’s Guide...
Page 422 Next, set another rule. Just open Firewall>>Filter Setup. Click the Set 2 link and choose the Filter Rule 3 button. Check the box of Check to enable the Filter Rule. Type the comments (e.g., open_ip). Click the Edit button for Source IP. Vigor2860 Series User’s Guide...
Page 423 End IP. Then, click OK to save the settings. The computers within the range can access into the Internet. Now, check the content of Source IP is correct or not. The action for Filter shall be set with Pass Immediately. Then, click OK to save the settings. Vigor2860 Series User’s Guide...
Page 424 Both filter rules have been created. Click OK. Now, all the settings are configured well. Only the computers with the IP addresses within 192.168.1.10 ~ 192.168.1.20 can access to Internet. Vigor2860 Series User’s Guide...
Page 425: Central Security Management (Csm)
Please note that this action will not introduce any delay in your Web surfing because each of multiple load balanced database servers can handle millions of requests for categorization. Info The priority of URL Content Filter is higher than Web Content Filter. Vigor2860 Series User’s Guide...
Page 426: Web User Interface
Click the number under Index column for settings in detail. There are four tabs IM, P2P, Protocol and Others displayed on this page. Each tab will bring out different items with supported versions that you can choose to disallow people using. Vigor2860 Series User’s Guide...
Page 427 A button under Enable check box allows you to open a pop up window to specify activity for that APP. The profiles configured here can be applied in the Firewall>>General Setup and Firewall>>Filter Setup pages as the standard for the host(s) to follow. Vigor2860 Series User’s Guide...
Page 428 Below shows the items which are categorized under Protocol. The items categorized under P2P ----- Vigor2860 Series User’s Guide...
Page 429 The items categorized under OTHERS----- Vigor2860 Series User’s Guide...
Page 430: Vi-2-2 Appe Signature Upgrade
The APPE Enforcement Profile adopted by Vigor router will be treated as the APPE signature. DrayTek will periodically upgrade versions for all of the APPs supported by Vigor router. However, it might be inconvenient for users to upgrade the APP version one by one. This feature is specially designed to offer a quick method to execute APP version upgrade.
Page 431 Upgrade Automatically Scheduled Update - Check the box to make Vigor router upgrading the APPE signature based on the schedule configured here. After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 432: Vi-2-3 Url Content Filter Profile
You can type the message manually for your necessity. Default Message - You can type the message manually for your necessity or click this button to get the default message which will be displayed on the field of Administration Message. Vigor2860 Series User’s Guide...
Page 433 URL Access Control and Web Feature below, such function can determine the priority for the actions executed. For this one, the router will process the packages with the conditions set below for web feature first, then URL second. Vigor2860 Series User’s Guide...
Page 434 After specifying keywords, the Vigor router will decline the connection request to the website whose URL string matched to any user-defined keyword. It should be noticed that the more simplified the blocking keyword list is, the more efficiently the Vigor router performs. Vigor2860 Series User’s Guide...
Page 435 File Extension Profile – Choose one of the profiles that you configured in Object Setting>> File Extension Objects previously for passing or blocking the file downloading. After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 436: Vi-2-4 Web Content Filter Profile
Please refer to section of creating MyVigor account. WCF adopts the mechanism developed and offered by certain service provider (e.g., DrayTek). No matter activating WCF feature or getting a new license for web content filter, you have to click Activate to satisfy your request.
Page 437 Setup Test Server It is recommended for you to use the default setting, auto-selected. Find more Click it to open http://myvigor.draytek.com for searching another qualified and suitable server. Test a site to verify Click this link to do the verification.
Page 438 Group/Object Selections – Click Edit to choose the group or object profile as the content of white/black list. Pass - allow accessing into the corresponding webpage with the characters listed on Group/Object Selections. If the web Vigor2860 Series User’s Guide...
Page 439 Block – Only the log about Block will be recorded in Syslog. All – All the actions (Pass and Block) will be recorded in Syslog. After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 440: Vi-2-5 Dns Filter Profile
It displays a list of different DNS filter profiles (with specified WCF and UCF). Click the profile link to open the following page. Then, type the name of the profile and specify WCF/UCF based on your requirement. Vigor2860 Series User’s Guide...
Page 441 Message button to get the default text displayed on the field of Administration Message. Preview – A dialog will appear to display the message typed in the Administration Message. After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 442: Application Notes
The website of MyVigor (a server located on http://myvigor.draytek.com) provides several useful services (such as Anti-Spam, Web Content Filter, Anti-Intrusion, and etc.) to filtering the web pages for the sake of protecting your system. To access into MyVigor for getting more information, please create an account for MyVigor.
Page 443 2. Click the Activate link. A login page for MyVigor web site will pop up automatically. 3. Click the link of Create an account now. 4. Check to confirm that you accept the Agreement and click Accept. Vigor2860 Series User’s Guide...
Page 444 5. Type your personal information in this page and then click Continue. 6. Choose proper selection for your computer and click Continue. Vigor2860 Series User’s Guide...
Page 445 8. Check to see the confirmation email with the title of Letter from myvigor.draytek.com. 9. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register process is finished. Please click Login. Vigor2860 Series User’s Guide...
Page 446 11. Now, click Login. Your account has been activated. You can access into MyVigor server to activate the service (e.g., WCF) that you want. 1. Access into http://myvigor.draytek.com. Find the line of Not registered yet?. Then, click the link Click here! to access into next page.
Page 447 2. Check to confirm that you accept the Agreement and click Accept. 3. Type your personal information in this page and then click Continue. 4. Choose proper selection for your computer and click Continue. 5. Now you have created an account successfully. Click START. Vigor2860 Series User’s Guide...
Page 448 6. Check to see the confirmation email with the title of New Account Confirmation Letter from myvigor.draytek.com. 7. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register process is finished. Please click Login. Vigor2860 Series User’s Guide...
Page 449 UserName and Password. Then type the code in the box of Auth Code according to the value displayed on the right side of it. Now, click Login. Your account has been activated. You can access into MyVigor server to activate the service (e.g., WCF) that you want. Vigor2860 Series User’s Guide...
Page 450: How To Block Facebook Service Accessed By The Users Via Web Content Filter / Url Content Filter
Benefits: Easily and quickly implement the category/website that you want to block. Note: License is required. URL Content Filter, Benefits: Free, flexible for customize webpage. Note: Manual setting (e.g., one keyword for one website.) Make sure the Web Content Filter (powered by Commtouch) license is valid. Vigor2860 Series User’s Guide...
Page 451 Open CSM >> Web Content Filter Profile to create a WCF profile. Check Social Networking with Action, Block. Enable this profile in Firewall>>General Setup>>Default Rule. Next time when someone accesses facebook via this router, the web page would be blocked and the following message would be displayed instead. Vigor2860 Series User’s Guide...
Page 452 In the field of Contents, please type facebook. Configure the settings as the following figure. Open CSM>>URL Content Filter Profile. Click an index number to open the setting page. Configure the settings as the following figure. When you finished the above steps, click OK. Then, open Firewall>>General Setup. Vigor2860 Series User’s Guide...
Page 453 B. Disallow users to play games on Facebook Open Object Settings>>Keyword Object. Click an index number to open the setting page. In the field of Contents, please type apps.facebook. Configure the settings as the following figure. Vigor2860 Series User’s Guide...
Page 454 When you finished the above steps, please open Firewall>>General Setup. Click the Default Rule tab. Choose the profile just configured from the drop down list in the field of URL Content Filter. Now, users cannot open any web page with the word “facebook” inside. Vigor2860 Series User’s Guide...
Page 455: Part Vii Management
Sessions Limit, Bandwidth Limit, and Quality of Servie (QoS). It is a security feature which disallows any IP traffic (except DHCP-related packets) from a particular host until that host has correctly supplied a valid username and password. Vigor2860 Series User’s Guide...
Page 456: System Maintenance
For the system setup, there are several items that you have to know the way of configuration: System Status, TR-069, Administrator Password, User Password, Login Page Greeting, Configuration Backup, Syslog /Mail Alert, Time and Date, Management, Reboot System, Firmware Upgrade and Activation. Below shows the menu items for System Maintenance. Vigor2860 Series User’s Guide...
Page 457: Web User Interface
IP Address - Display the IP address of the LAN interface. Subnet Mask - Display the subnet mask address of the LAN interface. DHCP Server - Display the current status of DHCP server of the LAN Vigor2860 Series User’s Guide...
Page 458 Scope - Display the scope of IPv6 address. For example, IPv6 Link Local could only be used for direct IPv6 link. It can't be used for IPv6 internet. Internet Access Mode – Display the connection mode chosen for accessing into Internet. Vigor2860 Series User’s Guide...
Page 459: Vii-1-2 Tr-069
CPE is able to communicate with VigorACS SI server. Event Code – Use the drop down menu to specify an event to perform the test. Last Inform Response Time – Display the time that VigorACS Vigor2860 Series User’s Guide...
Page 460 VigorAP.  AP Password – Type the password of the VigorAP that you want to apply Vigor2860’s TR-069 settings. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 461: Vii-1-3 Administrator Password
Local User – Check the box to enable the local user configuration. Local User List – It displays the username of the local user. User Name – Give a user name for the local user. Vigor2860 Series User’s Guide...
Page 462 LDAP Profile Setup. LDAP Profile Setup – It allows you to create a new LDAP profile. When you click OK, the login window will appear. Please use the new password to access into the web user interface again. Vigor2860 Series User’s Guide...
Page 463: Vii-1-4 User Password
Below shows an example for accessing into User Operation with User Password. 1. Open System Maintenance>>User Password. 2. Check the box of Enable User Mode for simple web configuration to enable user mode operation. Type a new password in the field of New Password and click OK. Vigor2860 Series User’s Guide...
Page 464 4. Log out Vigor router web user interface by clicking the Logout button. 5. The following window will be open to ask for username and password. Type the new user password in the filed of Password and click Login. Vigor2860 Series User’s Guide...
Page 465 Settings to be configured in User Mode will be less than settings in Admin Mode. Only basic configuration settings will be available in User Mode. Info Setting in User Mode can be configured as same as in Admin Mode. Vigor2860 Series User’s Guide...
Page 466: Vii-1-5 Login
Enable Check this box to enable the login customization function. Login Page Title Type a brief description (e.g., Welcome to DrayTek) which will be shown on the heading of the login dialog. Welcome Message and Type words or sentences here. It will be displayed for Bulletin bulletin message.
Page 467 Vigor2860 Series User’s Guide...
Page 468: Vii-1-6 Configuration Backup
Backup Click it to perform the configuration backup of this router. Protect with password- For the sake of security, the configuration file for the router can be encrypted. Vigor2860 Series User’s Guide...
Page 469  confirmation. Support Model List Web configuration file from other Vigor router can be applied to Vigor2860 series. At present, the configuration file of Vigor2820/Vigor2830/Vigor2850 is accepted for Vigor 2860. This field displays model name(s) and firmware which web configuration file saved can be used by such router.
Page 470 Click Choose File button to choose the correct configuration file for uploading to the router. Click Restore button and wait for few seconds, the following picture will tell you that the restoration procedure is successful. Vigor2860 Series User’s Guide...
Page 471: Vii-1-7 Syslog/Mail Alert
VPN, User Access, Call, WAN, Router/DSL information to Syslog. AlertLog Setup Check Enable to activate function of alert log. AlertLog Port - Type the port number for alert log. The Vigor2860 Series User’s Guide...
Page 472 For viewing the Syslog, please do the following: Just set your monitor PC’s IP address in the field of Server IP Address Install the Router Tools in the Utility within provided CD. After installation, click on the Router Tools>>Syslog from program menu. Vigor2860 Series User’s Guide...
Page 473 From the Syslog screen, select the router you want to monitor. Be reminded that in Network Information, select the network adapter used to connect to the router. Otherwise, you won’t succeed in retrieving information from the router. Vigor2860 Series User’s Guide...
Page 474: Vii-1-8 Time And Date
Advanced – Click it to open a pop up dialog. Use the default time setting or set user defined time for your requirement. Automatically Update Select a time interval for updating from the NTP server. Interval Click OK to save these settings. Vigor2860 Series User’s Guide...
Page 475: Vii-1-9 Snmp
The maximum length of the text is limited to 23 characters. Set Community Set community by typing a proper name. The default setting is private. The maximum length of the text is limited to 23 characters. Vigor2860 Series User’s Guide...
Page 476 Privacy Algorithm Choose one of the methods listed below as the privacy algorithm. Privacy Password Type a password for privacy. The maximum length of the text is limited to 23 characters. Click OK to save these settings. Vigor2860 Series User’s Guide...
Page 477: Vii-1-10 Management
The management pages for IPv4 and IPv6 protocols are different. Available settings are explained as follows: Item Description Router Name Type in the router name provided by ISP. Default: Disable If it is enabled, the function of auto-logout for web user Vigor2860 Series User’s Guide...
Page 478 SSL 3.0 to make sure you can connect, however, it's not recommended. CVM Access Control CVM Port – Check the box to enable such port setting. CVM SSL Port – Check the box to enable such port setting. Vigor2860 Series User’s Guide...
Page 479 A maximum of three IPs/subnet masks is allowed. IPv6 Address /Prefix Length- Indicate the IP address(es) allowed to login to the router. After finished the above settings, click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 480: Vii-1-11 Reboot System
When the system pops up Reboot System web page after you configure web settings, please click Reboot Now to reboot your router for ensuring normal operation and preventing unexpected errors of the router in the future. Vigor2860 Series User’s Guide...
Page 481: Vii-1-12 Firmware Upgrade
Download the newest firmware from DrayTek's web site or FTP site. The DrayTek web site is www.DrayTek.com (or local DrayTek's web site) and FTP site is ftp.DrayTek.com. Click System Maintenance>> Firmware Upgrade to launch the Firmware Upgrade Utility. Choose the right firmware by clicking Select. Then, click Upgrade. The system will upgrade the firmware of the router automatically.
Page 482: Vii-1-13 Modem Code Upgrade
The Activate link brings you accessing into www.vigorpro.com to finish the activation of the account and the router. Authentication Message As for authentication information of web filter, the process of authenticating will be displayed on this field for your reference. Vigor2860 Series User’s Guide...
Page 483 Below shows the successful activation of Web Content Filter: Vigor2860 Series User’s Guide...
Page 484: Vii-1-15 Internal Service User List
For the detailed setting (such as IP address, port number) configuration of internal RADIUS, refer to Applications>>RADIUS/TACACS+. For the detailed setting (such as IP address, port number) configuration of Local 802.1X, refer to LAN>>Wired 802.1X and Wireless LAN>>Security. Vigor2860 Series User’s Guide...
Page 485: Bandwidth Management
This is called per-hop-behavior (PHB). The definition of PHB includes Expedited Forwarding (EF), Assured Forwarding (AF), and Best Effort (BE). AF defines the four classes of delivery (or forwarding) classes and three levels of drop precedence in each class. Vigor2860 Series User’s Guide...
Page 486 However, each node may take different attitude toward packets with high priority marking since it may bind with the business deal of SLA among different DS domain owners. It’s not easy to achieve deterministic and consistent high-priority QoS traffic throughout the whole network with merely Vigor router’s effort. Vigor2860 Series User’s Guide...
Page 487: Web User Interface
Description Session Limit Enable - Click this button to activate the function of limit session. Disable - Click this button to close the function of limit session. Default session limit - Defines the default session number Vigor2860 Series User’s Guide...
Page 488 All the schedules can be set previously in Application >> Schedule web page and you can use the number that you have set in that web page. After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 489: Vii-2-2 Bandwidth Limit
Default RX limit - Define the default speed of the downstream for each computer in LAN. Allow auto adjustment…- Check this box to make the best utilization of available bandwidth. Limitation List Display a list of specific limitations that you set on this web page. Vigor2860 Series User’s Guide...
Page 490 Index (1-15) in Schedule Setup - You can type in four sets of time schedule for your request. All the schedules can be set previously in Application >> Schedule web page and you can use the number that you have set in that web page. Vigor2860 Series User’s Guide...
Page 491: Vii-2-3 Quality Of Service
Rule – Allow to configure detailed settings for the selected Class. Service Type – Allow to configure detailed settings for the service type. Enable the First Priority When this feature is enabled, the VoIP SIP/UDP packets will be Vigor2860 Series User’s Guide...
Page 492 You can configure general setup for the WAN interface, edit the Class Rule, and edit the Service Type for the Class Rule for your request. Display an online statistics for quality of service for your reference. This feature is available only when the Quality of Service for WAN interface is enabled. Vigor2860 Series User’s Guide...
Page 493 Check this and set the limited bandwidth ratio on the right Control field. This is a protection of TCP application traffic since UDP application traffic such as streaming video will exhaust lots of bandwidth. Outbound TCP ACK The difference in bandwidth between download and upload Vigor2860 Series User’s Guide...
Page 494 Edit link of that one. After you click the Edit link, you will see the following page. Now you can define the name for that Class. In this case, “Test” is used as the name of Class Index #1. Vigor2860 Series User’s Guide...
Page 495 Service Type drop down list. Those types are predefined in factory. Simply choose the one that you want for using by current QoS. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 496 Edit to open the rule edit page for modification. To add a new service type, edit or delete an existed service type, please click the Edit link under Service Type field. After you click the Edit link, you will see the following page. Vigor2860 Series User’s Guide...
Page 497 For example, in the following illustration, the VoIP packets in LAN go into Vigor router without any header. However, when they go forward to the Server on ISP through Vigor router, all of the packets are tagged with AF (configured in Bandwidth >>QoS>>Class) automatically. Vigor2860 Series User’s Guide...
Page 498: Application Notes
Internet connection line? The advanced bandwidth management technology-QoS (Quality of Service) helps you to well allocate the bandwidth upon your demand of Voice, Video, or Data transferring. Let's see how to get the optimum bandwidth per your request by using DrayTek Vigor router as below.
Page 499 In the pop-up window, choose Range Address as the Address Type and type the start IP address and end IP address in relational fields. Click OK to save the settings and exit the window. Click OK again to save the settings. Vigor2860 Series User’s Guide...
Page 500 The class rule for VoIP has been set. Click OK to return to previous page. Do the same steps to add class rules for IPTV and Data/Email with IP addresses as shown below. Vigor2860 Series User’s Guide...
Page 501 10. In the Setup page, check the box of Enable the QoS Control. Type 30, 50 and 15 in the boxes for VoIP, IPTV and Data/Email respectively. Check the box of Enable UDP Bandwidth Control. 11. Click OK to save the settings. The class rules for WAN1 are defined as shown below. Vigor2860 Series User’s Guide...
Page 502: Qos Setting Example
Skype in the restroom. Go to Bandwidth Management>>Quality of Service. Click Setup link of WAN(1/2/3). Make sure the QoS Control on the left corner is checked. And select BOTH in Direction. Set Inbound/Outbound bandwidth. Vigor2860 Series User’s Guide...
Page 503 E-mail using protocol POP3 and SMTP. Click OK to save the settings. Return to previous page. Enter the Name of Index Class #2 by clicking Edit link. In this index, the user will set reserved bandwidth for HTTPS. And click OK. Vigor2860 Series User’s Guide...
Page 504 Click OK. If the worker has connected to the headquarter using host to host VPN tunnel. (Please refer to Chapter 3 VPN for detail instruction), he may set up an index for it. Enter the Vigor2860 Series User’s Guide...
Page 505 Class Name of Index 3. In this index, he will set reserved bandwidth for 1 VPN tunnel. 10. Click Edit for Class 3 to open a new window. In this index, the user will set reserved bandwidth for VPN. 11. Click Add to open the following window. Check the ACT box, first. Vigor2860 Series User’s Guide...
Page 506 12. Then click Edit of Local Address to set a worker’s subnet address. Click Edit of Remote Address to set headquarter’s IP address. Leave other fields and click OK. Vigor2860 Series User’s Guide...
Page 507: User Management
Filter rules configured under Firewall usually are applied to the host (the one that the router installed) only. With user management, the rules can be applied to every user connected to the router with customized profiles. Vigor2860 Series User’s Guide...
Page 508: Web User Interface
User-Based - If you choose such mode, the router will apply the filter rules configured in User Management>>User Profile to the users. Rule-Based –If you choose such mode, the router will apply the filter rules configured in Firewall>>General Setup and Vigor2860 Series User’s Guide...
Page 509 Landing Page Type the information to be displayed on the first web page when the LAN user accessing into Internet via such router. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 510: Vii-3-2 User Profile
To set the user profile, please click any index number link to open the following page. Notice that profile 1 (admin) and profile 2 (Dial-In User) are factory default settings. Profile 2 is reserved for future use. Vigor2860 Series User’s Guide...
Page 511 Firewall can be adopted for such user profile. Create New Policy – If you choose such item, the following page will be popped up for you to define another filter rule as a new policy. Vigor2860 Series User’s Guide...
Page 512 Alert Tool – If it is selected, the user can open Alert Tool and type the user name and password for authentication. A window with remaining time of connection for such user will Vigor2860 Series User’s Guide...
Page 513 Next, the user can access Internet through any browser on Windows. Note that Alert Tool can be downloaded from DrayTek web site. Telnet – If it is selected, the user can use Telnet command to perform the authentication job.
Page 514 RADIUS Check the box to enable security authenticated via RADIUS server. Local 802.1X Check the box to enable security authenticated via 802.1X server. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 515: Vii-3-3 User Group
All the available user objects that you have created will be shown in this box. Notice that user object, Admin and Dial-In User are factory settings. User defined profiles will be numbered with 3, 4, 5 and so on. Vigor2860 Series User’s Guide...
Page 516: Vii-3-4 User Online Status
Display the login time that such user connects to the router last time. Expired Time Display the expired time of the network connection for the user. Data Quota Display the quota for data transmission. Idle Time Display the idle timeout setting for such profile. Vigor2860 Series User’s Guide...
Page 517 Action Block - can avoid specified user accessing into Internet. Unblock – allow the user to access into Internet. Logout – the user will be logged out forcefully. Vigor2860 Series User’s Guide...
Page 518: Application Notes
If a LAN client who hasn’t passed the authentication opens an external web site in his browser, he will be redirected to the router’s Web authentication interface first. Then, the client is trying to access http://www.draytek.com and but brought to the Vigor router. Since this is an SSL connection, some web browsers will display warning messages.
Page 519 With Microsoft Internet Explorer, you may get the following warning message.  Please press Continue to this website (not recommended). With Mozilla Firefox, you may get the following warning message. Select I  Understand the Risks. Vigor2860 Series User’s Guide...
Page 520 If the authentication is successful, the client will be redirected to the original web site that he tried to access. In this example, it is http://www.draytek.com . Furthermore, you will get a popped up window as the following. Then you can access the Internet.
Page 521 192.168.1.1 with your router’s real IP address, and add the port number if the default management port has been modified. If the authentication is successful, you will get the Welcome Message that is set in the User Management >> General Setup page. Vigor2860 Series User’s Guide...
Page 522 With the default setup <body stats=1><script language='javascript'> window.location='http://www.draytek.com'</script></body>, you will be redirected to http://www.draytek.com . You may change it if you want. For example, you will get the following welcome message if you enter Login Successful in the Welcome Message table.
Page 523 If SSL Tunnel or SSL Web Proxy is disabled in the VPN profile, a User Management account and a remote dial-in VPN profile can use the same Username, even with different passwords. However, we recommend you to use different usernames for different user profiles in User Management and VPN profiles. Vigor2860 Series User’s Guide...
Page 524 Here expired time is “Unlimited” means the Time Quota function is not enabled for this account. After login, this account will not be expired until it is logout. In the Web interface of router, the configuration page of Time Quota is shown as below. Vigor2860 Series User’s Guide...
Page 525 You will get the following message. The expired time is shown after you login. After you run out the available time, you can’t use this account any more until the administrator manually adds additional time for you. Vigor2860 Series User’s Guide...
Page 526 Any modification to the Firewall policy will break down the connections of all current users. They all have to authenticate again for Internet access. Info 2 The administrator may check the current users from User Online Status page. Vigor2860 Series User’s Guide...
Page 527: How To Use Landing
Landing Page is a special feature configured under User Management. It can specify the message, content to be seen or specify which website to be accessed into when users try to access into the Internet by passing the authentication. Here, we take Vigor2860 series router as an example.
Page 528 Open any browser (e.g., FireFox, Internet Explorer). The logging page will appear and asks for username and password. Please type the correct username and password. Click Login. If the logging is successful, you will see the message of Login Success from the browser you use. Vigor2860 Series User’s Guide...
Page 529 Next, enable the Landing Page function. Open User Management -> User Profile and click one of the index number (e.g., index number 3) links. In the following page, check the box of Landing page and click OK to save the settings. Vigor2860 Series User’s Guide...
Page 530 Open any browser (e.g., FireFox, Internet Explorer). The logging page will appear and asks for username and password. Please type the correct username and password. Click Login. If the logging is successful, you will be directed into the website of www.draytek.com. Vigor2860 Series User’s Guide...
Page 531: Central Ap Management (Cam)
The parameters configured for Load Balance can help to distribute the traffic for all of the access points registered to Vigor router. Thus, the bandwidth will not be occupied by certain access points. Vigor2860 Series User’s Guide...
Page 532: Web User Interface
To access into the web user interface of VigorAP, simply move your mouse cursor on the VigorAP icon and click it. The system will guide you to access into the web user interface of VigorAP. Vigor2860 Series User’s Guide...
Page 533: Vii-4-2 Status
Display the firmware version used by the access point. Password Vigor2860 can get related information of the access point by accessing into the web user interface of the access point. This button is used to modify the logging password of the connected access point. Vigor2860 Series User’s Guide...
Page 534: Vii-4-3 Wlan Profile
It can copy settings from an existing WLAN profile to another WLAN profile. First, you have to check the box of the existing profile as the original profile. Second, click Clone. The following dialog will appear. Vigor2860 Series User’s Guide...
Page 535 Simply choose the device you want from Existing Device field. Click >> to move the device to Selected Device field. Then, click OK. The selected WLAN profile will be applied to the selected access point immediately. Later the access point will reboot. Vigor2860 Series User’s Guide...
Page 536 2. Click the Edit button to display the following page. Info The function of Auto Provision is available for the default WLAN profile. 3. After finished the general settings configuration, click Next to open the following page for 2.4G wireless security settings. Vigor2860 Series User’s Guide...
Page 537 4. After finished the above web page configuration, click Next to open the following page for 5G wireless security settings. 5. When you finished the above web page configuration, click Finish to exit and return to the first page. The modified WLAN profile will be shown on the web page. Vigor2860 Series User’s Guide...
Page 538: Vii-4-4 Ap Maintenance
Specify the file and the path which will be used to perform Config Restore or Firmware Upgrade. Select Device Display all the available access points managed by Vigor router. Simply click << or >> to move the device(s) between Vigor2860 Series User’s Guide...
Page 539: Vii-4-5 Ap Map
View Click it to review the layout for the selected AP map. Edit Click it to modify the geographic settings for the selected AP Map profile. Cancel Click it to cancel the configuration in such page. Vigor2860 Series User’s Guide...
Page 540 PNG are supported) for floor plan. Cancel Click it to cancel the configuration. Next Click it to go to the next configuration page. Click Next. The configuration page with floor plan will be shown as follows. Vigor2860 Series User’s Guide...
Page 541 Choose the signal strength (e.g., 30% in this case) from User Define drop down list. Click Apply. Adjust the AP on the map to find out which place can have the best wireless coverage. At last, click Save. Vigor2860 Series User’s Guide...
Page 542: Vii-4-6 Traffic Graph
LAN-B, daily or weekly for viewing data transmission chart. Click Refresh to renew the graph at any time. The horizontal axis represents time; the vertical axis represents the transmission rate (in kbps). Info Enabling/Disabling such function will also enable/disable the External Devices function. Vigor2860 Series User’s Guide...
Page 543: Vii-4-7 Rogue Ap Detection
Available settings are explained as follows: Item Description Enable Neighbor AP Detection – The access point(s) registered to Vigor2860 will be used to detect other access points and send the scanned results to Vigor2860. Later, the scanned result Vigor2860 Series User’s Guide...
Page 544 AP is friendly and which one is Rogue respectively. Follow the steps below to perform the classification of access points. 1. Click the radio button on one of the access points. In this case, DrayTek-LAN-A is selected. 2. Later, some options will appear on the bottom of the page.
Page 545 AP, simply choose the one and click Delete. Later, the page will refresh and the one will be classified as Unknown. 3. Click OK to save the settings. The following figure shows the APs classified and displayed in different colors. Vigor2860 Series User’s Guide...
Page 546: Vii-4-8 Event Log
Time and event log for all of the APs managed by Vigor router will be shown on this page. It is userful for troubleshooting if required. Such page will display the total traffic of data receiving and data transmitting for VigorAPs managed by Vigor router. Vigor2860 Series User’s Guide...
Page 547: Vii-4-10 Station Number
The purpose is to prevent lots of stations connecting to access point at the same time and causing traffic unbalanced. Please define the required station number for WLAN (2.4GHz) and WLAN (5GHz) separately. Vigor2860 Series User’s Guide...
Page 548: Vii-4-12 Function Support List
Click the Client tab to list the AP management functions that the Access Points support under different firmware versions. Click the Server tab to list the AP management functions that Vigor router supports under different firmware versions. Vigor2860 Series User’s Guide...
Page 549: Application Notes
Edit button be available. Then, click the Edit button. When the following configuration page appears, make the changes you want and check Apply to All APs. Then, click Next to access into the next page. Vigor2860 Series User’s Guide...
Page 550 “plug and play” and “zero-configuration”. The following page allows you to modify related settings for 2.4G SSID of managed AP. Make the changes you want for 2.4G SSID. Click Next for next page. Vigor2860 Series User’s Guide...
Page 551 AP. Continue to make any changes you want. After finished all of the changes, simply click Finish. Now, the AP (represented with AP800_00507F6EE4980) detected by Vigor router will be applied with the settings modified by Vigor router. Vigor2860 Series User’s Guide...
Page 552: External Devices
You can change the device name if required or remove the information for off-line device whenever you want. When you finished the configuration, click OK to save it. Vigor2860 Series User’s Guide...
Page 553 Info Only DrayTek products can be detected by this function. Vigor2860 Series User’s Guide...
Page 554: Part Viii Others
USB device connected on Vigor router can be regarded as a server or WAN interface. By way of Vigor router, clients on LAN can access, write and read data stored in USB storage disk with different applications. Vigor2860 Series User’s Guide...
Page 555: Viii-1 Objects Settings
Later, we can select that object/group that can apply it. For example, all the IPs in the same department can be defined with an IP object (a range of IP address). Vigor2860 Series User’s Guide...
Page 556: Web User Interface
Display the name of the object profile. To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Vigor2860 Series User’s Guide...
Page 557 Type the MAC address of the network card which will be controlled. Start IP Address Type the start IP address for Single Address type. End IP Address Type the end IP address if the Range Address type is Vigor2860 Series User’s Guide...
Page 558 If it is checked, all the IP addresses except the ones listed above will be applied later while it is chosen. After finishing all the settings here, please click OK to save the configuration. Below is an example of IP objects settings. Vigor2860 Series User’s Guide...
Page 559: Viii-1-2 Ip Group
Display the name of the group profile. To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Vigor2860 Series User’s Guide...
Page 560: Viii-1-3 Ipv6 Object
You can set up to 64 sets of IPv6 Objects with different conditions. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the object profile. Vigor2860 Series User’s Guide...
Page 561 Invert Selection If it is checked, all the IPv6 addresses except the ones listed above will be applied later while it is chosen. After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 562: Viii-1-4 Ipv6 Group
Display the name of the group profile. To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Vigor2860 Series User’s Guide...
Page 563: Viii-1-5 Service Type Object
You can set up to 96 sets of Service Type Objects with different conditions. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the object profile. Vigor2860 Series User’s Guide...
Page 564 (>) – the port number greater than this value is available. (<) – the port number less than this value is available for this profile. Vigor2860 Series User’s Guide...
Page 565: Viii-1-6 Service Type Group
This page allows you to bind several service types into one group. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the group profile. Vigor2860 Series User’s Guide...
Page 566 Objects Setting>>Service Type Object will be shown in this box. Selected Service Type Click >> button to add the selected IP objects in this box. Objects After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 567: Viii-1-7 Keyword Object
You can set 200 keyword object profiles for choosing as black /white list in CSM >>URL Web Content Filter Profile. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the object profile. Vigor2860 Series User’s Guide...
Page 568 Contents. When you browse the webpage, the page with gambling information will be watched out and be passed/blocked based on the configuration on Firewall settings. After finishing all the settings, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 569: Viii-1-8 Keyword Group
Display the name of the group profile. To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Vigor2860 Series User’s Guide...
Page 570: Viii-1-9 File Extension Object
All the files with the extension names specified in these profiles will be processed according to the chosen action. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the object profile. Vigor2860 Series User’s Guide...
Page 571 Type a name for this profile. The maximum length of the name you can set is 7 characters. Type a name for such profile and check all the items of file extension that will be processed in the router. Finally, click OK to save this profile. Vigor2860 Series User’s Guide...
Page 572: Viii-1-10 Sms/Mail Service Object
Display the service provider which offers SMS service. To set a new profile, please do the steps listed below: 1. Click the SMS Provider tab, and click the number (e.g., #1) under Index column for configuration in details. Vigor2860 Series User’s Guide...
Page 573 Note that one credit equals to one SMS text message on the standard route. Sending Interval To avoid quota being exhausted soon, type time interval for sending the SMS. 3. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 574 Provider. You have to contact your SMS provider to obtain the exact URL string. Username Type a user name that the sender can use to register to selected SMS provider. The maximum length of the name you can set is 31 characters. Vigor2860 Series User’s Guide...
Page 575 Each item is explained as follows: Item Description Set to Factory Default Clear all of the settings and return to factory default settings. Index Display the profile number that you can configure. Profile Display the name for such mail server profile. Vigor2860 Series User’s Guide...
Page 576 Username – Type a name for authentication. The maximum length of the name you can set is 31 characters. Password – Type a password for authentication. The maximum length of the password you can set is 31 characters. Vigor2860 Series User’s Guide...
Page 577: Viii-1-11 Notification Object
You can set an object with different monitoring situation. To set a new profile, please do the steps listed below: 1. Open Object Setting>>Notification Object, and click the number (e.g., #1) under Index column for configuration in details. Vigor2860 Series User’s Guide...
Page 578 Central VPN Management is checked. Once such profile is enabled, Vigor router system will send out notification to the recipient via SMS. 3. After finishing all the settings here, please click OK to save the configuration. Vigor2860 Series User’s Guide...
Page 579: Application Notes
Choose any index number (e.g., Index 1 in this case) to configure the SMS Provider setting. In the following page, type the username and password and set the quota that the router can send the message out. Vigor2860 Series User’s Guide...
Page 580 Choose any index number (e.g., Index 1 in this case) to configure conditions for sending the SMS. In the following page, type the name of the profile and check the Disconnected and Reconnected boxes for WAN to work in concert with the topic of this paper. Vigor2860 Series User’s Guide...
Page 581 Click OK to save the settings. Later, if one of the WAN connections fails in your router, the system will send out SMS to the phone number specified. If the router has only one WAN interface, the system will send out SMS to the phone number while reconnecting the WAN interface successfully. Vigor2860 Series User’s Guide...
Page 582 URL string of the SMS provider and type the username and password. After clicking OK, the new added SMS provider will be added and will be available for you to specify for sending SMS out. Vigor2860 Series User’s Guide...
Page 583: Viii-2 Usb Application
USB ports on Vigor router are allowed to connect to USB modem. Models of the modems supported by Vigor router can be seen from USB Application>>Modem Support List. For network connection via USB modem, refer to WAN>>Internet Access and WAN>>General Setup for detailed information. Vigor2860 Series User’s Guide...
Page 584: Web User Interface
FTP sessions. The router allows up to 6 FTP sessions connecting to USB storage disk at one time. Default Charset - At present, Vigor router supports four types of character sets. Default Charset is for English based file name. Vigor2860 Series User’s Guide...
Page 585: Viii-2-2 Usb User Management
USB storage disk must type the same username and password configured in this page. Before adding or modifying settings in this page, please insert a USB storage disk first. Otherwise, an error message will appear to warn you. Click index number to access into configuration page. Vigor2860 Series User’s Guide...
Page 586 ON, you cannot type any new folder name in this field. Only “/” can be used in such case. You can click to open the following dialog to add any new folder which can be specified as the Home Folder. Vigor2860 Series User’s Guide...
Page 587: Viii-2-3 File Explorer
Available settings are explained as follows: Item Description Click this icon to refresh files list. Refresh Click this icon to return to the upper directory. Back Click this icon to add a new folder. Create Current Path Display current folder. Vigor2860 Series User’s Guide...
Page 588: Viii-2-4 Usb Device Status
FTP server. Username It displays the username that user uses to login to the FTP server. When you insert USB device into the Vigor router, the system will start to find out such device within several seconds. Vigor2860 Series User’s Guide...
Page 589: Viii-2-5 Temperature Sensor
A USB Thermometer is now available. It complements your installed DrayTek router installations which will help you monitor the server or data communications room environment and notify you if the server room or data communications room is overheating. During summer in particular, it is important to ensure that your server or data communications equipment are not overheating due to cooling system failures.
Page 590 Enable Syslog Alarm - The temperature log will be recorded on Syslog if it is enabled. Upper temperature limit/Lower temperature limit - Type the upper limit and lower limit for the system to send out temperature alert. Below shows an example of temperature graph: Vigor2860 Series User’s Guide...
Page 591: Viii-2-6 Modem Support List
Such page provides the information about the brand name and model name of the USB modems which are supported by Vigor router. Vigor2860 Series User’s Guide...
Page 592: Viii-2-7 Smb Client Support List
SMB Client Support List provides the test status information for applications with file sharing operated under different platforms. Vigor2860 Series User’s Guide...
Page 593: Application Notes
Plug the USB device to the USB port on the router. Make sure Disk Connected appears on the Connection Status as the figure shown below: Then, please open USB Application >> USB General Settings to enable SMB service. Vigor2860 Series User’s Guide...
Page 594 "user1" and assign authorities “Read”, “Write” and “List” to it. Click OK to save the configuration. Make sure the FTP service is running properly. Please open a browser and type ftp://192.168.1.1. Use the account "user1" to login. Vigor2860 Series User’s Guide...
Page 595 Now, users in LAN of Vigor2860 can access into the USB storage device by typing ftp://192.168.1.1 on any browser. They can add or remove files / directories, depending on the Access Rule for FTP account settings in USB Application >>USB User Management. Vigor2860 Series User’s Guide...
Page 596: Part Ix Troubleshooting
This part will guide you to solve abnormal situations if you cannot access into the Internet after installing the router and finishing the web configuration. Vigor2860 Series User’s Guide...
Page 597: Ix-1Diagnostics
Backing to factory default setting if necessary.  If all above stages are done and the router still cannot run normally, it is the time for you to contact your dealer or DrayTek technical support for advanced help. Vigor2860 Series User’s Guide...
Page 598: Web User Interface
(e.g., PPPoE) is triggered by a package sending from the source IP address. Available settings are explained as follows: Item Description Decoded Format It shows the source IP address (local), destination IP (remote) address, the protocol and length of the package. Refresh Click it to reload the page. Vigor2860 Series User’s Guide...
Page 599: Ix-1-2 Routing Table
Click Diagnostics and click Routing Table to open the web page. Available settings are explained as follows: Item Description Refresh Click it to reload the page. Vigor2860 Series User’s Guide...
Page 600: Ix-1-3 Arp Cache Table
Available settings are explained as follows: Item Description Show Specify LAN and VLAN to display related information. In default, this page will display all of the information about LAN and VLAN. Refresh Click it to reload the page. Vigor2860 Series User’s Guide...
Page 601: Ix-1-4 Ipv6 Neighbour Table
Click it to reload the page. The facility provides information on IP address assignments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click DHCP Table to open the web page. Vigor2860 Series User’s Guide...
Page 602: Ix-1-6 Nat Sessions Table
HOST ID It displays the host ID name of the specified PC. Refresh Click it to reload the page. Click Diagnostics and click NAT Sessions Table to open the list page. Available settings are explained as follows: Vigor2860 Series User’s Guide...
Page 603 Click OK to enable such function. It means when the TTL value of each DNS query reaches the threshold of the value specified here, the corresponding record will be deleted from router’s Cache automatically. Vigor2860 Series User’s Guide...
Page 604 Use the drop down list to choose the WAN/LTE interface that you want to ping through or choose Unspecified to be determined by the router automatically. Ping to Use the drop down list to choose the destination that you want to ping. Vigor2860 Series User’s Guide...
Page 605 Flow Monitor. If not, a notification dialog box will appear to remind you enabling it. Click Diagnostics and click Data Flow Monitor to open the web page. You can click IP Address, TX rate, RX rate or Session link for arranging the data display. Vigor2860 Series User’s Guide...
Page 606 Peak means the highest peak value detected by the router in data transmission. Speed means line speed specified in WAN>>General Setup. If you do not specify any rate at that page, here will display Auto for instead. Vigor2860 Series User’s Guide...
Page 607 WAN1/WAN2/WAN3/LTE/WAN4 Bandwidth chart, the numbers displayed on vertical axis represent the numbers of the transmitted and received packets in the past. For Sessions chart, the numbers displayed on vertical axis represent the numbers of the NAT sessions during the past. Vigor2860 Series User’s Guide...
Page 608 Available settings are explained as follows: Item Description IPv4 / IPv6 Click one of them to display corresponding information for it. Trace through Use the drop down list to choose the interface that you want to ping through. Vigor2860 Series User’s Guide...
Page 609 Click this link to refresh this page manually. Clear Click this link to clear information on this page. Display Mode There are two modes for you to choose. Stop record when fulls – when the capacity of syslog is full, Vigor2860 Series User’s Guide...
Page 610 If TSPC has configured properly, the router will display the following page when the user connects to tunnel broker successfully. Available settings are explained as follows: Item Description Refresh Click this link to refresh this page manually. Vigor2860 Series User’s Guide...
Page 611 When the mouse cursor moves to the name link under User Name, the connection message (including authentication failed information) about internal RADIUS or local 802.1X service will be shown by a popped up dialog box. This page will display the complete authentication log information. Vigor2860 Series User’s Guide...
Page 612 Always record the new event – only the newest events  will be recorded by the system. Time Display the time the user authenticated by Vigor2860 series. Message Display authentication information done by Vigor2860 series. Vigor2860 Series User’s Guide...
Page 613 Moreover, IP address detected and suspected to attack the network system can be blocked shortly by clicking the Block button shown on pages of SYN Flood, UDP Flood and ICMP Flood. Info The icon - - means there is something wrong (e.g., attacking the system) with that IP address. Vigor2860 Series User’s Guide...
Page 614 IP list in the right frame will be blocked by Vigor system permanatly. Remove – It is used to remove selected IP address from the Blocking IP List. Refresh Click this link to refresh current page. Vigor2860 Series User’s Guide...
Page 615 Turn on the router. Make sure the ACT LED blink once per second and the correspondent LAN LED is bright. If not, it means that there is something wrong with the hardware status. Simply back to “I-2 Hardware Installation” to execute the hardware installation again. And then, try again. Vigor2860 Series User’s Guide...
Page 616 Open All Programs>>Getting Started>>Control Panel. Click Network and Sharing Center. In the following window, click Change adapter settings. Icons of network connection will be shown on the window. Right-click on Local Area Connection and click on Properties. Vigor2860 Series User’s Guide...
Page 617 Select Internet Protocol Version 4 (TCP/IP) and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically. Finally, click OK. Vigor2860 Series User’s Guide...
Page 618 Double click on the current used Mac OS on the desktop. Open the Application folder and get into Network. On the Network screen, select Using DHCP from the drop down list of Configure IPv4. Vigor2860 Series User’s Guide...
Page 619 Open the Application folder and get into Utilities. Double click Terminal. The Terminal window will appear. Type ping 192.168.1.1 and press [Enter]. If the link is OK, the line of “64 bytes from 192.168.1.1: icmp_seq=0 ttl=255 time=xxxx ms” will appear. Vigor2860 Series User’s Guide...
Page 620 Vigor2860 Series User’s Guide...
Page 621  If the problem of LEDs cannot be solved by the above measures, please contact with the nearest reseller, or send an e-mail to DrayTek FAE for technical support.  Check if the settings offered by ISP are configured well or not.
Page 622 PIN code and try again. If it still fails, it might be the compliance problem of system. Please open DrayTek Syslog Tool to capture the connection information (WAN Log) and send the page (similar to the following graphic) to the service center of DrayTek.
Page 623 While the router is running (ACT LED blinking), press the Factory Reset button and hold for more than 5 seconds. When you see the ACT LED blinks rapidly, please release the button. Then, the router will restart with the default configuration. Vigor2860 Series User’s Guide...
Page 624 After restore the factory default setting, you can configure the settings for the router again to fit your personal request. Vigor2860 Series User’s Guide...
Page 625 If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@DrayTek.com. Vigor2860 Series User’s Guide...
Page 626 VLAN helps you to solve these situations, and DrayTek’s products support bellow two popular types:...
Page 627 P1 and P2 are doing NAT flow to access to the internet, but P3 and P4 will forward the packets between WAN and LAN ports directly. So far, there are two kinds of open system on Vigor router. One is DrayOS, which is DrayTek owned, and another is Linux-like which customized by DrayTek from OpenWRT. Here DrayOS system is going to be introduced to you because it is the most stable and superfast booting system in DrayTek products.
Page 628 Vigor2860 Series User’s Guide...
Page 629  Multi Subnet (VLAN of LAN) Vigor2860 Series User’s Guide...
Page 630 Port-based is able to extend the wired ports by installing a cheaper dumb switch as many as you need, but Tag-based offers you a flexible and well-managed network. The networks are isolated, secured and reduce the broadcasting storm effectively in each of networks with VLAN.  Guest Network Vigor2860 Series User’s Guide...
Page 631 Tag enabled.  Triple Play (Multi-WAN) NAT mode with VLAN Following settings, the set-top box (STB) is able to attach with any LAN port. Video streaming which your ISP provided will be played on your monitor. Vigor2860 Series User’s Guide...
Page 632 Vigor2860 Series User’s Guide...
Page 633 Set-top box (STB) or the other kinds of media devices are able to attach with Port4 or Port5 of LAN. Those devices that attached with Port4 or Port5 are able to access the services network directly which your ISP provided. Vigor2860 Series User’s Guide...
Page 634 Vigor2860 Series User’s Guide...
Page 635 If you have changed the default, enter the current IP address of the router. Next, type admin/admin for Account/Password. Then, type ?. You will see a list of valid/common commands depending on the router that your use. Vigor2860 Series User’s Guide...
Page 636 For users using previous Windows system (e.g., 2000/XP), simply click Start >> Run and type Telnet 192.168.1.1 in the Open box as below. Next, type admin/admin for Account/Password. And, type ? to get a list of valid/common commands. Vigor2860 Series User’s Guide...
Page 637 : 00000000 DSLAM CHIPSET VENDOR : < ADI > > This command can set the Internet Access mode for the router. adsl ppp [ ? | pvc_no vci vpi Encap Proto modu acqIP idle [Username Password] Vigor2860 Series User’s Guide...
Page 638 This parameter is used only for PPPoE/PPPoA Password This parameter is used only for PPPoE/PPPoA You have to reboot the system when you set it on Route mode. > adsl ppp o 35 8 1 1 4 1 -1 draytek draytek pvc no.=0 vci=35 vpi=8...
Page 639 It means the number of LAN port (x=2~4). Port 1 is locked for NAT. > adsl bridge 4 on p2 p3 PVC Bridge Service Type ------------------------------------------------------------ Normal -1(OFF) PVC 0 & 1 can't set for bridge mode. Please use 'save' to save config. Vigor2860 Series User’s Guide...
Page 640 4. Now, it is on continuous sending mode, and adsl2/2+ led is always ON. 5. Use 'adsl reboot' to restart dsl to normal mode. This command can reboot the router. > adsl reboot % Adsl is Rebooting... Vigor2860 Series User’s Guide...
Page 641 Some ISP might set the vci value under 32. In such case, we can cancel such limit manually by using this command. Do not set the number greater than 254. adsl vcilimit [n] The number shall be between 1 ~ 254. > adsl vcilimit 33 change VCI limitation from 32 to 33. Vigor2860 Series User’s Guide...
Page 642 This command can display the allocation for each Bin (Tone) SNR, Gain, and Bits. adsl showbins [startbin endbin | up] Parameter Description startbin The number is between 0 ~ 4092. endbin The number is between 4 ~ 4095. Show upstream information. > adsl showbins 2 30 DOWNSTREAM : Vigor2860 Series User’s Guide...
Page 643 [0: default(=3), 2: OFF, 3: ON , 4: DYNAMIC_SOS] retx [US] = ON, [DS] = aelem G.Vector This command can save the configuration into FLASH with a file format of cfg. > adsl savecfg % Xdsl Cfg Save OK! Vigor2860 Series User’s Guide...
Page 644 It means Sustainable Cell Rate. It means Maximum Burst Size. status It means to display PCR/SCR/MBS setting. > adsl atm pcr 1 200 max % PCR is 200 for pvc 1. > adsl atm pcr status channel --------------------------- Vigor2860 Series User’s Guide...
Page 645 This command is used to display information about CO or CPE. adsl inventory [co|cpe] Parameter Description It means DSLAM (Digital Subscriber Line Access Multiplexer) or CO (Central Office). It means CPE (Customer Premise Equipment). > adsl inventory co xDSL inventory info only available in showtime. Vigor2860 Series User’s Guide...
Page 646 This command can make the router accessing into the idle status. If you want to invoke the router again, you have to reboot the router by using “reboot” command. vdsl idle [on | tcpmessage | tcpmessage_off] Parameter Description DSL is under test mode. DSL debug tool mode is off. Vigor2860 Series User’s Guide...
Page 647 This command can display the allocation for each Bin (Tone) SNR, Gain, and Bits. vdsl showbins [startbin endbin | up] Parameter Description startbin The number is between 0 ~ 4092. endbin The number is between 4 ~ 4095. Show upstream information. Vigor2860 Series User’s Guide...
Page 648 ON, [DS] = aelem G.Vector This command can save the configuration into FLASH with a file format of cfg. > vdsl savecfg % Xdsl Cfg Save OK! This command allows you to configure user-defined CPE vendor ID. Vigor2860 Series User’s Guide...
Page 649 : 0XB5004946544E0000 System country code : 0XB500 System provider code : IFTN System vendor info : 0X000 Version number : 3.8.2_RC4a_STD Version number(16 octets) : 0X332E382E325F524334615F5354440000 Self-test result : PASS Transmission mode capability : 0X40004004C010400 > Vigor2860 Series User’s Guide...
Page 650 5 : WA(61.9.240.13) -l <List> List all settings configured. > bpa 1 -a 1 -n testUser -p testPassword -s 4 > bpa -l -------index: 1 active------ UserName[1]: testUser PassWord[1]: testPassword ServerIP[1]:4 -------index: 2 inactive------ UserName[2]: PassWord[2]: ServerIP[2]:0 > Vigor2860 Series User’s Guide...
Page 651 ACTION Specify the action of the application, 0 or 1. 0: Block. All of the applications meet the CSM rule will be blocked. 1: Pass. All of the applications meet the CSM rule will be passed. Vigor2860 Series User’s Guide...
Page 652 Specify the index number of CSM profile, from 1 to 32. View the configuration status of IM group. View the configuration status of P2P group. View the configuration status of protocol group. View the configuration status of Others group. > csm appe config -v 1 -m Vigor2860 Series User’s Guide...
Page 653 Vigor router specifies WAN interface automatically. Specify the WAN interface for signature downloading. > csm appe interface wan1 Download interface is set as "WAN1" now. > csm appe interface auto Download interface is set as "auto-selected" now. Vigor2860 Series User’s Guide...
Page 654 It means to specify the index number of CSM profile, from 1 to 8. It means to set the profile name. PROFILE_NAME It means to specify the name of the profile (less than 16 characters) Set the priority (defined by the number specified in VALUE) for the profile. Vigor2860 Series User’s Guide...
Page 655 INDEX uac -i E|D csm ucf obj INDEX uac -o KEY_WORD_Object_Index csm ucf obj INDEX uac -g KEY_WORD_Group_Index Parameter Description INDEX It means to specify the index number of CSM profile, from 1 to 8. Vigor2860 Series User’s Guide...
Page 656 Profile Name:[game] Log:[none] Priority Select : [Bundle : Pass] [ ]Enable URL Access Control Action:[block] [v]Prevent web access from IP address. No Obj NO. Object Name --- -------- --------------------------------- No Grp NO. Group Name --- -------- --------------------------------- Vigor2860 Series User’s Guide...
Page 657 Log:[none] Priority Select : [Bundle : Pass] [ ]Enable URL Access Control Action:[block] [v] Prevent web access from IP address. No Obj NO. Object Name --- -------- --------------------------------- No Grp NO. Group Name --- -------- --------------------------------- Vigor2860 Series User’s Guide...
Page 658 P: Pass. The web access meets the web feature will be passed. It means to set the profile name. PROFILE_NAME It means to specify the name of the profile (less than 16 characters) It means the log type of the profile. They are: Vigor2860 Series User’s Guide...
Page 659 Transportation, Compromised, Dating & Personals, , Education, Finance, Government,Health & Medcine, News, Non-profits & NGOs, Personal Sites,Politics, Real Estate, Rligion, Restaurants & Dining,Shopping, Translators, General, Cults,Greetig cards, Image Sharing, Network Errors, Parked Domains, Private IP Addresses) Vigor2860 Series User’s Guide...
Page 660 CACHE_TIME csm dnsf blockpage show/on/off csm dnsf profile_show csm dnsf profile_edit INDEX csm dnsf profile_edit INDEX -n PROFILE_NAME csm dnsf profile_edit INDEX -l N|P|B|A csm dnsf profile_edit INDEX -w WCF_PROFILE csm dnsf profile_edit INDEX -u UCF_PROFILE Vigor2860 Series User’s Guide...
Page 661 1 to 24; 1 is one hour, 2 is two hours, and so on ...) for DNS filter. > csm dnsf service 2 dns service set up!!! >csm dnsf service 3 wcf profile 3 is empty..>csm dnsf cachetime 1 dns cache time set up!!! Vigor2860 Series User’s Guide...
Page 662 It means to specify the name of flooding attack(s) or portscan, e.g., synflood, udpflood, icmpflood, or postscan. THRESHOLD It means the packet rate (packet/second) that a flooding attack will be detected. Set a value larger than 20. Vigor2860 Series User’s Guide...
Page 663 It means to set PPP Authentication Type and n means different types (represented by 0-1). n=0: PAP/CHAP (this is default setting) n=1: PAP Only -t n It means to set connection duration and n means different conditions. Vigor2860 Series User’s Guide...
Page 664 -N <apn name> Set (DHCP mode) APN Name (max. 47 characters) -U n (DHCP mode) MTU(1000-1440) >internet -M 1 -S tcom -u username -p password -a 0 -t -1 -i 0.0.0.0 WAN1 Internet Mode set to PPPoE/PPPoA Vigor2860 Series User’s Guide...
Page 665 Display an IP address which allows users set as the public subnet IP address. public subnet IP address Specify an IP address. The system will set the one that you specified as the public subnet IP address. > ip pubaddr ? % ip addr <public subnet IP address> Vigor2860 Series User’s Guide...
Page 666 0 (disable) or 1 (enable). wanX Add or remove an address for WAN interface. index Type the index number of the table displayed on your screen. > ip aux add 192.168.1.65 1 % 192.168.1.65 has added in index 2. Vigor2860 Series User’s Guide...
Page 667 IP address of the PC must be fixed with the same LAN IP address (network segment) set by this command for accessing into the web user interface of the router. Later, modify the start addresses for the DHCP server. Vigor2860 Series User’s Guide...
Page 668 3: enable to accept illegal dest mac address 4: Decline VRRP mac into arp table 5: Accept VRRP mac into arp table status: display the setting status. Time Available settings will be 10, 20, 30,..2550 seconds. Vigor2860 Series User’s Guide...
Page 669 It means to release current WAN IP address. renew It means to renew the WAN IP address and obtain another new one. status It displays current status of DHCP client. >ip dhcpc status I/F#3 DHCP Client Status: Vigor2860 Series User’s Guide...
Page 670 [Host/IP address] [WAN1/WAN2/WAN3/WAN4/WAN5] [Udp/Icmp] Parameter Description IP address It means the target IP address. WAN1/WAN2 It means the WAN port that the above IP address passes through. Udp/Icmp It means the UDP or ICMP. Vigor2860 Series User’s Guide...
Page 671 This command allows users to set the RIP (routing information protocol) of IP. ip rip [0/1/2] Parameter Description 0/1/2 0 means disable; 1 means first subnet and 2 means second subnet. > ip rip 1 %% Set RIP 1st subnet. Vigor2860 Series User’s Guide...
Page 672 <ifno> 1: WAN1,2: WAN2 3: PVC3,4: PVC4,5: PVC5 -e <0/1> 0: disable, 1: enable Now status: WAN[1] Rip Protocol disable WAN[2] Rip Protocol disable WAN[3] Rip Protocol disable WAN[4] Rip Protocol disable WAN[5] Rip Protocol enable Vigor2860 Series User’s Guide...
Page 673 > ip route add 172.16.2.0 255.255.255.0 172.16.2.4 3 static > ip route status Codes: C - connected, S - static, R - RIP, * - default, ~ - private 192.168.1.0/ 255.255.255.0 is directly connected, LAN1 172.16.2.0/ 255.255.255.0 via 172.16.2.4, WAN1 Vigor2860 Series User’s Guide...
Page 674 %IGMP Proxy Interface: WAN5(PVC) %WAN5 for Router-borne Application/ IPTV on/off: ON > ip igmp_proxy query 130000 This command is for setting IGMP General Query Interval The default value is 125000 ms Current Setting is:130000 ms > Vigor2860 Series User’s Guide...
Page 675 It means to display the current settings. show It means to display all session limit settings in the IP range. timer [num] It means to set when the IP session block works. The unit is second. Vigor2860 Series User’s Guide...
Page 676 It means to display all the bandwidth limits settings within the IP range. It means to add the bandwidth within the IP range. It means to delete the bandwidth within the IP range. IP1-IP2 It means the range of IP address specified for this command. Vigor2860 Series User’s Guide...
Page 677 It means to type the IP address for binding with specified MAC address. It means to type the MAC address for binding with the IP address specified. Comment It means to type words as a brief description. It means to delete all the IP bindmac settings. Vigor2860 Series User’s Guide...
Page 678 > ip bindmac add 192.168.1.46 00:50:7f:22:33:55 just for test > ip bindmac show ip bind mac function is turned ON IP : 192.168.1.46 bind MAC : 00-50-7f-22-33-55 Comment : just Vigor2860 Series User’s Guide...
Page 679 It means to type a fixed value as the length of the prefix. LAN|WAN1|WAN2|iface# It means to specify LAN or WAN interface for such address. > ip6 addr -a Unicast Address: FE80::250:7FFF:FE00:0/64 (Link) Multicast Address: FF02::2 FF02::1:FF00:0 FF02::1 Vigor2860 Series User’s Guide...
Page 680 % Interface WAN2 is set to request following DHCPv6 options: sip name > This command allows you to use DHCPv6 protocol to obtain IPv6 address from server. ip6 dhcp client [WAN1|WAN2|iface#] [-<command> <parameter>| ... ] Parameter Description client It means the dhcp client settings. Vigor2860 Series User’s Guide...
Page 681 It means to set the second DNS IPv6 address. -c<parameter> It means to send rapid commit to server. 1: Enable 0: Disable -e<parameter> It means to enable or disable the DHCPv6 server. 1: Enable 0: Disable Vigor2860 Series User’s Guide...
Page 682 It means to set Username. <username>= type a name as the username (maximum 63 characters). -p <password> It means to set Password. <password> = type a password (maximum 63 characters). -s <server> It means to set Tunnel Server IP. Vigor2860 Series User’s Guide...
Page 683 Specify an interface for the neighbor. > ip6 neigh -s 2001:2222:3333::1111 00:50:7F:11:ac:22:WAN2 Neighbour 2001:2222:3333::1111 successfully added! > ip6 neigh -a I/F ADDR STATE ------------------------------------------------------------------------- LAN FF02::1 33-33-00-00-00-01 CONNECTED WAN2 2001:5C0:1400:B::10B8 00-00-00-00-00-00 CONNECTED WAN2 2001:2222:3333::1111 00-00-00-00-00-00 CONNECTED WAN2 2001:2222:6666::1111 00-00-00-00-00-00 CONNECTED Vigor2860 Series User’s Guide...
Page 684 WAN2 :: 00-00-00-00-00-00 CONNECTED LAN :: NONE > Vigor2860 Series User’s Guide...
Page 685 It means the gateway of the router. LAN|WAN1|WAN2|iface# It means to specify LAN or WAN interface for such address. > ip6 route -s FE80::250:7FFF:FE12:500 16 FE80::250:7FFF:FE12:100 LAN Route FE80::250:7FFF:FE12:500/16 successfully added! > ip6 route -a LAN Vigor2860 Series User’s Guide...
Page 686 Receive reply from 2001:4860:4860::8888, time=330ms Receive reply from 2001:4860:4860::8888, time=330ms Receive reply from 2001:4860:4860::8888, time=330ms Receive reply from 2001:4860:4860::8888, time=330ms Receive reply from 2001:4860:4860::8888, time=330ms Packets: Sent = 5, Received = 5, Lost = 0 <% loss> > Vigor2860 Series User’s Guide...
Page 687 > ip6 tspc 2 Local Endpoint v4 Address : 111.243.177.223 Local Endpoint v6 Address : 2001:05c0:1400:000b:0000:0000:0000:10b9 Router DNS name : 8886666.broker.freenet6.net Remote Endpoint v4 Address :81.171.72.11 Remote Endpoint v6 Address : 2001:05c0:1400:000b:0000:0000:0000:10b8 Tspc Prefixlen : 56 Tunnel Broker: Amsterdam.freenet.net Vigor2860 Series User’s Guide...
Page 688 Description list It means to show the setting information of the access list. status It means to show the status of IPv6 management. It means to add an IPv6 address which can be used to execute Vigor2860 Series User’s Guide...
Page 689 It means the connection interface. 0=LAN1 1=WAN1 2=WAN2 > ip6 online 0 % LAN 1 online status : % Interface : UP % IPv6 DNS Server: :: Static % IPv6 DNS Server: :: Static % IPv6 DNS Server: :: Static Vigor2860 Series User’s Guide...
Page 690 > ip6 aiccu subnet add 2 2001:1111:0000::1111 64 > ip6 aiccu 2 Status: Connecting >ip6 aiccu subnet show 2 IPv6 WAN2 AICCU Subnet Prefix Config: 2001:1111::1111/64 > This command allows you to set IPv6 settings for NTP (Network Time Protocols) server. Vigor2860 Series User’s Guide...
Page 691 > ipf view -V -c -d ipf: IP Filter: v3.3.1 (1824) Kernel: IP Filter: v3.3.1 Running: yes Log Flags: 0x80947278 = nonip Default: pass all, Logging: available This command is used to set general rule for firewall. Vigor2860 Series User’s Guide...
Page 692 Setting saved. > ipf set -d 2 #set data filter start from set 2 Setting saved. > ipf set -v Call Filter: Enable (Start Filter Set = 1) Data Filter: Enable (Start Filter Set = 2) Vigor2860 Series User’s Guide...
Page 693 It means to configure source IP address including address type, Address> <End IP Address> | start IP address, end IP address and address mask. <Address Mask> u – It means “user defined”. Address Type - Type the number (representing different address Vigor2860 Series User’s Guide...
Page 694 4 – Port range of the Start Port Number, range is 1-65535. 6 – Port range of the End Port Number, range is 1-65535. It means the Filter action you can specify. 0 –Pass Immediately, 1 – Block Immediately, Vigor2860 Series User’s Guide...
Page 695 It is used to show current filter/rule settings. > ipf rule 2 1 -e 1 -s "o 1" -d "o 2" -S "o 1" -F 2 > ipf rule 2 1 -v Filter Set 2 Rule 1: Vigor2860 Series User’s Guide...
Page 696 [-i][-p][-t] Parameter Description It means to refresh the flowtrack. It means to enable or disable the flowtrack. 0: Disable 1: Enable It means to show the sessions state of flowtrack. If you do not Vigor2860 Series User’s Guide...
Page 697 It means to show the flush log buffer. a: flush all logs c: flush the call log f: flush the IP filter log w: flush the WAN log It means to show this usage help. It means to show PPP/MP log. Vigor2860 Series User’s Guide...
Page 698 FTP port It means to type the number for FTP port. The default setting is > mngt ftpport 21 % Set FTP server port to 21 done. This command allows users to set HTTP port for management. Vigor2860 Series User’s Guide...
Page 699 It means to type the number for telnet port. The default setting is > mngt telnetport 23 % Set Telnet server port to 23 done. This command allows users to set SSH port for management. mngt sshport [ssh port] Vigor2860 Series User’s Guide...
Page 700 All PING packets will be blocked from LAN PC to Internet. viewlog It means to display a log of ping action, including source MAC and source IP. clearlog It means to clear the log of ping action. Vigor2860 Series User’s Guide...
Page 701 > mngt noping off No Ping Packet Out is OFF!! Vigor2860 Series User’s Guide...
Page 702 Description status It means to display current setting for your reference. enable It means to allow the system administrators to login from the Internet. disable It means to deny the system administrators to login from the Vigor2860 Series User’s Guide...
Page 703 It means to flush all of the settings. It means to restore the factory default settings. It means to view current settings. It means to get the usage of such command. > mngt lanaccess -e 1 > mngt lanaccess -s FTP,TELNET Vigor2860 Series User’s Guide...
Page 704 This command allows you to specify that the system administrator can login from a specific host or network. A maximum of three IPs/subnet masks is allowed. mngt accesslist list mngt accesslist add [index][ip addr][mask] mngt accesslist remove [index] mngt accesslist flush Vigor2860 Series User’s Guide...
Page 705 It means to set the IPv4 address of the host that will receive the trap community. -T <seconds> It means to set the trap timeout <0~999>. It means to list SNMP setting. > mngt snmp -e 1 -g draytek -s DK -m 192.168.1.1 -t trapcom -n 10.20.3.40 Vigor2860 Series User’s Guide...
Page 706 -T 88 SNMP Agent Turn on!!! Get Community set to draytek Set Community set to DK Manager Host IP set to 192.168.1.1 Trap Community set to trapcom Notification Host IP set to 10.20.3.40 Trap Timeout set to 88 seconds This command is used to configure multi-subnet.
Page 707 This setting will take effect after rebooting. Please use "sys reboot" command to reboot the router. This command is used to display current status of subnet. msubnet status [2/3/4/5/6] Parameter Description 2/3/4/5/6 It means LAN interface. 2=LAN2 3=LAN3 4=LAN4 5=LAN5 6=LAN6 Vigor2860 Series User’s Guide...
Page 708 2=LAN2 3=LAN3 4=LAN4 5=LAN5 6=LAN6 On/Off On – It means the subnet will be configured for NAT usage. Off - It means the subnet will be configured for Routing usage. > > msubnet nat 2 off Vigor2860 Series User’s Guide...
Page 709 [2/3/4] [IP counts] Parameter Description 2/3/4/5/6 It means LAN interface. 2=LAN2 3=LAN3 4=LAN4 5=LAN5 6=LAN6 IP counts Specify a total number of IP address allowed for each LAN interface. The available range is from 0 to 220. Vigor2860 Series User’s Guide...
Page 710 LAN3 LAN4 LAN5 LAN6 % LAN1 % LAN2 % LAN3 % LAN4 % LAN5 % LAN6 > This command is used to configure a starting IP address for DCHP. msubnet startip [2/3/4/5/6] [Gateway IP] Parameter Description Vigor2860 Series User’s Guide...
Page 711 This setting will take effect after rebooting. Please use "sys reboot" command to reboot the router. > msubnet pppip ? % msubnet pppip <2/3/4/5/6> <Start IP> % Now: LAN2 192.168.2.250; LAN3 192.168.3.200; LAN4 192.168.4.200; LAN5 192.168.5.200; LAN6 192.168.6.200 Vigor2860 Series User’s Guide...
Page 712 % Now: LAN2 1; LAN3 0; LAN4 0; LAN5 0; LAN6 0 % count: 1. B-node 2. P-node 4. M-node 8. H-node This command is used to configure primary WINS server. msubnet primWINS [2/3/4/5/6] [WINS IP] Parameter Description 2/3/4/5/6 It means LAN interface. 2=LAN2 3=LAN3 4=LAN4 Vigor2860 Series User’s Guide...
Page 713 > > msubnet secWINS 2 192.168.3.89 % Set LAN2 Dhcp Secondary WINS IP done !!! > msubnet secWINS ? % msubnet secWINS <2/3/4/5/6> <WINS IP> % Now: LAN2 192.168.3.89; LAN3 0.0.0.0; LAN4 0.0.0.0; LAN5 0.0.0.0; LAN6 0.0.0.0 Vigor2860 Series User’s Guide...
Page 714 LAN4 LAN5 LAN6 This command allows you to configure MTU value for LAN/DMZ/IP Routed Subnet. msubnet mtu [interface][value] Parameter Description interface Available settings include LAN1~LAN6, IP_Routed_Subnet, and DMZ. value 1000 ~ 1508 (Bytes), default: 1500 (Bytes) Vigor2860 Series User’s Guide...
Page 715 NAME: Type a name with less than 15 characters. Example: object ip obj 9 -n bruce -i INTERFACE It means to define an interface for the IP object. INTERFACE=0, means any INTERFACE=1, means LAN INTERFACE=3, means WAN Example: object ip obj 8 -i 0 Vigor2860 Series User’s Guide...
Page 716 It means to define a name for the IP group. NAME: Type a name with less than 15 characters. Example: object ip grp 8 -n bruce -i INTERFACE It means to define an interface for the IP group. Vigor2860 Series User’s Guide...
Page 717 [6:][0] [7:][0] > object ip grp 2 -i 1 > object ip grp 2 -a 1 2 IP Group Profile 2 Name :[First] Interface:[Lan] Included ip object index: [0:][1] [1:][2] [2:][0] [3:][0] [4:][0] [5:][0] [6:][0] [7:][0] Vigor2860 Series User’s Guide...
Page 718 Type an IP address (different with START_IP) as the end IP address. > object ip obj 1 -n marketing > object ip obj 1 -a 1 192.168.1.45 > object ip obj 1 -v IP Object Profile 1 Name :[marketing] Vigor2860 Series User’s Guide...
Page 719 The IP object profiles with index number 1,2,3,4 and 5 will be group under such profile. > object ip grp 2 -n First IP Group Profile 2 Name :[First] Interface:[Any] Included ip object index: [0:][0] [1:][0] [2:][0] [3:][0] [4:][0] [5:][0] [6:][0] Vigor2860 Series User’s Guide...
Page 720 PROTOCOL =255, means TCP/UDP Other values mean other protocols. Example: object service obj 8 -i 0 It means the check action for the port setting. 0=equal(=), when the starting port and ending port values are the Vigor2860 Series User’s Guide...
Page 721 It means the index number of the specified group profile. It means to view the information of the specified group profile. Example: object service grp 1 -v -n NAME It means to define a name for the service group. Vigor2860 Series User’s Guide...
Page 722 INDEX -n NAME object kw obj INDEX -a CONTENTS Parameter Description setdefault It means to return to default settings for all profiles. show PAGE It means to show the contents of the specified profile. Vigor2860 Series User’s Guide...
Page 723 It means to view the information of the specified file extension object profile. -n NAME It means to define a name for the file extension object profile. NAME: Type a name with less than 15 characters. It means to enable the specific CATEGORY or FILE_EXTENSION. Vigor2860 Series User’s Guide...
Page 724 [ ].ocx [ ].olb [ ].ole [ ].tlb [ ].viv [ ].vrm ------------------------------------------------------------------------- ------ Compression category: [ ].ace [ ].arj [ ].bzip2 [ ].bz2 [ ].cab [ ].gz [ ].gzip [ ].rar [ ].sit [ ].zip Vigor2860 Series User’s Guide...
Page 725 ------------------------------------------------------------------------- ------ Executation category: [ ].bas [ ].bat [ ].com [ ].exe [ ].inf [ ].pif [ ].reg [ ].scr Vigor2860 Series User’s Guide...
Page 726 The available commands with parameters are listed below. <parameter>|…] […] means that you can type in several commands in one line. -t <sec> It means “TCP” protocol. <sec>: Type a number to set the TCP session timeout. Vigor2860 Series User’s Guide...
Page 727 > prn status Interface: USB bus 2.0 Printer: NotReady > prn debug conn[0] : none conn[1] : none conn[2] : none conn[3] : none LPD_data_total=0 usblp_ptr=0 UsbPrintReady=0, UsbIsPrinting=0 This command allows user to set general settings for QoS. Vigor2860 Series User’s Guide...
Page 728 WAN1 class 3 ratio set to 20 WAN1 udp bandwidth control set to enable WAN1 udp bandwidth limit ratio set to 50 WAN1 Outbound TCP ACK Prioritizel set to enable QoS WAN1 set complete; restart QoS > Vigor2860 Series User’s Guide...
Page 729 Specify the service type by typing the number. The available types are listed as below: 1:ANY 2:DNS 3:FTP 4:GRE 5:H.323 6:HTTP 7:HTTPS 8:IKE 9:IPSEC-AH 10:IPSEC-ESP 11:IRC 12:L2TP 13:NEWS 14:NFS 15:NNTP 16:PING 17:POP3 18:PPTP 19:REAL-AUDIO 20:RTSP 21:SFTP 22:SIP 23:SMTP 24:SNMP 25:SNMP-TRAPS 26:SQL-NET 27:SSH 28:SYSLOG 29:TELNET 30:TFTP Vigor2860 Series User’s Guide...
Page 730 Show the rule in the specified class. […] It means that you can type in several commands in one line. > qos class -c 2 -n draytek -a -m 1 -l 192.168.1.50:192.168.1.80 Following setting will set in the class2 class 2 name set to draytek...
Page 731 > qos type -a draytek -t 6 -p 510:1330 service name set to draytek service type set to 6:TCP Port type set to Range Service Port set to 510 ~ 1330 > This command can exit the telnet command screen.
Page 732 ******************************************************** No data entry. This command displays current status of NAT. > show nat Port Redirection Running Table: Index Protocol Public Port Private IP Private Port 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 Vigor2860 Series User’s Guide...
Page 733 % Maximum Session Number: 10000 % Maximum Session Usage: 49 % Current Session Usage: 0 % Current Session Used(include waiting for free): 0 % WAN1 Current Session Usage: 0 This command displays current status of LAN and WAN connections. Vigor2860 Series User’s Guide...
Page 734 This command displays statistics for WAN interface. show statistic show statistic reset [interface] Parameter Description reset It means to reset the transmitted/received bytes to Zero. interface It means to specify WAN1 ~WAN5 (including multi-PVC) interface for displaying related statistics. Vigor2860 Series User’s Guide...
Page 735 WAN1 total TX: 0 Bytes ,RX: 0 Bytes WAN2 total TX: 0 Bytes ,RX: 0 Bytes WAN3 total TX: 0 Bytes ,RX: 0 Bytes WAN4 total TX: 0 Bytes ,RX: 0 Bytes WAN5 total TX: 0 Bytes ,RX: 0 Bytes > Vigor2860 Series User’s Guide...
Page 736 It means all of the MAC addresses. Vigor> ip route add 192.168.1.56 255.255.255.0 192.168.1.12 3 default Vigor> srv dhcp public status Index MAC Address This command allows users to set Primary IP Address for DNS Server in LAN. srv dhcp dns1 [?] Vigor2860 Series User’s Guide...
Page 737 Note: The IP Routed Subnet DNS must be the same as NAT Subnet DNS). > srv dhcp dns2 10.1.1.1 % srv dhcp dns2 <DNS IP address> % Now: 10.1.1.1 (IP Routed Subnet dns same as NAT Subnet dns) Vigor2860 Series User’s Guide...
Page 738 It means to display current gateway that you can use. Gateway IP It means to specify a gateway address used for DHCP server. > srv dhcp gateway 192.168.2.1 This setting will take effect after rebooting. Please use "sys reboot" command to reboot the router. Vigor2860 Series User’s Guide...
Page 739 1 or 2 specified here. > srv dhcp relay servip 192.168.1.46 > srv dhcp relay subnet 2 > srv dhcp relay servip ? % srv dhcp relay servip <server ip> % Now: 192.168.1.46 Vigor2860 Series User’s Guide...
Page 740 This command can display general information for the DHCP server, such as IP address, MAC address, leased time, host ID and so on. > srv dhcp status DHCP server: Relay Agent Default gateway: 192.168.1.1 Index IP Address MAC Address Leased Time HOST ID 192.168.1.113 00-05-5D-E4-D8-EE 17:20:08 A1000351 Vigor2860 Series User’s Guide...
Page 741 It means to specify a type for node. 1. B-node 2. P-node 4. M-node 8. H-node > srv dhcp nodetype 1 > srv dhcp nodetype ? %% srv dhcp nodetype <count> %% 1. B-node 2. P-node 4. M-node 8. H-node % Now: 1 Vigor2860 Series User’s Guide...
Page 742 It means to remove the IP address settings of second WINS server. > srv dhcp secWINS 192.168.1.180 > srv dhcp secWINS ? %% srv dhcp secWINS <WINS IP address> %% srv dhcp secWINS clear % Now: 192.168.1.180 Vigor2860 Series User’s Guide...
Page 743 -e [1 or 0] -c [option number] -v [option value] srv dhcp option -e [1 or 0] -c [option number] -a [option value] srv dhcp option -e [1 or 0] -c [option number] -x [option value] srv dhcp option -u [idx unmber] Vigor2860 Series User’s Guide...
Page 744 It means the index number of the option value. > srv dhcp option -e 1 -c 18 -v /path > srv dhcp option -l % state idx interface opt type data % enable 1 ALL LAN 18 ASCII /path Vigor2860 Series User’s Guide...
Page 745 The available commands with parameters are listed below. It means to enable IPSec ESP tunnel passthrough and IKE source port (500) preservation. It means to disable IPSec ESP tunnel passthrough and IKE source port (500) preservation. Vigor2860 Series User’s Guide...
Page 746 It means to return to factory settings for all the open ports profiles. > srv nat openport 1 1 -a 1 -c games -i 192.168.1.100 -w 1 -p TCP -s 23 -e 83 > srv nat openport -v Vigor2860 Series User’s Guide...
Page 747 It means to remove the selected port redirection setting. disable [idx] It means to inactivate the selected port redirection setting. enable [idx] It means to activate the selected port redirection setting. flush It means to clear all the port mapping settings. Vigor2860 Series User’s Guide...
Page 748 Protocol: 0 = Disable, 6 = TCP, 17 = UDP This command allows users to view NAT Port Redirection Running Table. > srv nat status NAT Port Redirection Running Table: Index Protocol Public Port Private IP Private Port 192.168.1.11 0.0.0.0 0.0.0.0 0.0.0.0 Vigor2860 Series User’s Guide...
Page 749 This command is used to obtain the TX (transmitted) or RX (received) data for each connected switch. switch -i [switch idx_no] [option] Parameter Description switch idx_no It means the index number of the switch profile. option The available commands with parameters are listed below. Vigor2860 Series User’s Guide...
Page 750 This command is used to reset the switch table and reboot the router. switch clear [idx] Parameter Description It means the index number of each item shown on the table. The range is from 1 to 8. It means to clear all of the data. Vigor2860 Series User’s Guide...
Page 751 Username – Type a new name for local user. Password – Type a password for local user. delete [INDEX] Delete a local user account. view [INDEX] Show the user account/password detail information. > > sys adminuser Local 1 Vigor2860 Series User’s Guide...
Page 752 It is used to disable/enable SSH service (0: disable, 1: enable). -p <enable> It is used to disable/enable printer service (0: disable, 1: enable). -6 <enable> It is used to disable/enable IPv6 (0: disable, 1: enable). > sys bonjour -s 1 > Vigor2860 Series User’s Guide...
Page 753 Parameter Description It means to turn on the FTP server of the system. It means to turn off the FTP server of the system. > sys ftpd on % sys ftpd turn on !!! Vigor2860 Series User’s Guide...
Page 754 Interface 4 Ethernet: Status: DOWN IP Address: 0.0.0.0 Netmask: 0x00000000 MAC: 00-50-7F-00-00-02 Interface 5 Ethernet: Status: DOWN IP Address: 0.0.0.0 Netmask: 0x00000000 MAC: 00-50-7F-00-00-03 Interface 6 Ethernet: Status: DOWN IP Address: 0.0.0.0 Netmask: 0x00000000 MAC: 00-50-7F-00-00-04 Vigor2860 Series User’s Guide...
Page 755 Interface 8 Ethernet: Status: DOWN IP Address: 0.0.0.0 Netmask: 0x00000000 MAC: 00-50-7F-00-00-06 Interface 9 Ethernet: Status: DOWN IP Address: 0.0.0.0 Netmask: 0x00000000 MAC: 00-50-7F-00-00-07 --- MORE --- ['q': Quit, 'Enter': New Lines, 'Space Bar': Next Page] > Vigor2860 Series User’s Guide...
Page 756 Description ASCII string It means the password for administrator. The maximum character that you can set is 23. > sys passwd admin123 > This command allows users to restart the router immediately. > sys reboot > Vigor2860 Series User’s Guide...
Page 757 This command can turn on TFTP server for upgrading the firmware. > sys tftpd % TFTP server enabled !!! This command can display current country code and wireless region of this device. > sys cc Country Code : 0x 0 [International] Wireless Region Code: 0x30 > Vigor2860 Series User’s Guide...
Page 758 # of lost by siganture = 0 # of lost by list = 0 This command can turn on or turn off polling buffer for the router. sys pollbuf [on] sys pollbuf [off] Parameter Description It means to turn on pulling buffer. Vigor2860 Series User’s Guide...
Page 759 [on/off] sys tr069 save sys tr069 inform [event code] sys tr069 port [port num] sys tr069 cert_auth [on/off] Parameter Description get [parm] [option] It means to get parameters for tr-069. option=<nextlevel>: only gets nextlevel for GetParameterNames. Vigor2860 Series User’s Guide...
Page 760 > sys tr069 get Int. nextlevel Total number of parameter is 24 Total content length of parameter is 915 InternetGatewayDevice.LANDeviceNumberOfEntries InternetGatewayDevice.WANDeviceNumberOfEntries InternetGatewayDevice.DeviceInfo. InternetGatewayDevice.ManagementServer. InternetGatewayDevice.Time. InternetGatewayDevice.Layer3Forwarding. InternetGatewayDevice.LANDevice. InternetGatewayDevice.WANDevice. InternetGatewayDevice.Services. InternetGatewayDevice.X_00507F_InternetAcc. InternetGatewayDevice.X_00507F_LAN. InternetGatewayDevice.X_00507F_NAT. InternetGatewayDevice.X_00507F_Firewall. InternetGatewayDevice.X_00507F_Bandwidth. InternetGatewayDevice.X_00507F_Applications. InternetGatewayDevice.X_00507F_VPN. InternetGatewayDevice.X_00507F_VoIP. InternetGatewayDevice.X_00507F_WirelessLAN. InternetGatewayDevice.X_00507F_System. InternetGatewayDevice.X_00507F_Status. InternetGatewayDevice.X_00507F_Diagnostics. Vigor2860 Series User’s Guide...
Page 761 It means the license register server setting. licera It means to erase license setting. licifno It means license and signature download interface setting. lic_wiz [set/reg/qry] It means the license wizard setting. qry: query service support status Vigor2860 Series User’s Guide...
Page 762 DRVTAPI, DRVVMMC, DRVMPS, DRVFXO, DRVHAL, PSMPHONE, PSMSUPP, PSM, FXO, PSMISDN, DTMFPSER, CALLERID (Case-Insensitive). It means the dump log buffer. > sys diag_log status Status: diag_log is Enabled. lineno : 10000. Vigor2860 Series User’s Guide...
Page 763 This command is used to display current settings for sending test mail. > testmail Send out test mail Mail Alert:[Disable] SMTP_Server:[0.0.0.0] Mail to:[] Return-Path:[] This command can close UPnP function. >upnp off UPNP say bye-bye This command can enable UPnP function. Vigor2860 Series User’s Guide...
Page 764 This command can display the information of the UPnP service. UPnP service must be enabled first. > upnp on UPNP start. > upnp service >>>>> SERVICE TABLE1 <<<<< serviceType urn:schemas-microsoft-com:service:OSInfo:1 serviceId urn:microsoft-com:serviceId:OSInfo1 SCPDURL /upnp/OSInfo.xml controlURL /OSInfo1 eventURL /OSInfoEvent1 uuid:774e9bbe-7386-4128-b627-001daa843464 >>>>> SERVICE TABLE2 <<<<< serviceType urn:schemas-upnp-org:service:WANCommonInterfaceConfig:1 serviceId urn:upnp-org:serviceId:WANCommonIFC1 Vigor2860 Series User’s Guide...
Page 765 >>>> (2) serviceType urn:schemas-upnp-org:service:WANCommonInterfaceConfig:1 ----- Subscribtion1 ------- sid = d9cd47a5-d9c9-4d3d-8043-d03a82f27983 eventKey =1, ToSendEventKey = 1 This command can display current status of temp Virtual Server of your router. Vigor> upnp tmpvs ****************** Temp virtual server status **************** ((0)) Vigor2860 Series User’s Guide...
Page 766 Aiko Aiko 83D 3.5G BandRich Bandluxe C170 3.5G BandRich Bandluxe C270 3.5G BandRich Bandluxe C321 3.5G BandRich Bandluxe C330 3.5G BandRich Bandluxe C331 3.5G BandRich Bandluxe C502 3.5G Huawei Huawei E169u 3.5G Huawei Huawei E220 3.5G Vigor2860 Series User’s Guide...
Page 767 This command can disable vigor bridge function. > vigbrg off %Disable Vigor Bridge Function! This command can show whether the Vigor Bridge Function is enabled or disabled. > vigbrg status %Vigor Bridge Function is enable! %Wan1 management is disable! Vigor2860 Series User’s Guide...
Page 768 [list index] peerid [peerid] vpn l2lset [list index] localid [localid] vpn l2lset [list index]main [auto/proposal index] vpn l2lset [list index] aggressive [g1/g2] vpn l2lset [list index]pfs [on/off] vpn l2lset [list index] phase1[lifetime] vpn l2lset [list index] phase2[lifetime] Vigor2860 Series User’s Guide...
Page 769 It means to enable or disable the profile. on – Enable. off – Disable. motp <on/off> It means to enable or disable the authentication with mOTP function. on – Enable. off – Disable. pin_secret<pin> <secret> It means to set PIN code with secret. Vigor2860 Series User’s Guide...
Page 770 Idle Timeout: 300 sec This command allows users to specify a subnet selection for the specified remote dial-in VPN profile. vpn subnet [index] [1/2/3/4/5/6] Parameter Description <index> It means the index number of the VPN profile. Vigor2860 Series User’s Guide...
Page 771 It means the IP address to dial to. <key> It means the value of IPsec Pre-Shared Key. <nip> <nmask> It means the remote network IP and the mask. e.g., vpn setup 1 name1 ipsec_out 1.2.3.4 1234 192.168.1.0 255.255.255.0 For L2TP Dial-Out Vigor2860 Series User’s Guide...
Page 772 % Remote NEtwork Mask : 255.255.255.0 > This command allows users to configure settings for LAN to LAN profile. vpn option <index> <cmd1>=<param1> [<cmd2>=<para2> | ... ] Parameter Description <index> It means the index number of the profile. Vigor2860 Series User’s Guide...
Page 773 “ctype= l” means L2TP(IPSec Policy None). “ctype= l1” means L2TP(IPSec Policy Nice to Have). “ctype= l2” means L2TP(IPSec Policy Must). dialto It means Server IP/Host Name for VPN. (such as draytek.com or 123.45.67.89). ltype It means Link Type. “ltype=0” means “Disable”.
Page 774 Type “off” means any remote IP is allowed to dial in. peerid It means the peer ID for Remote VPN Gateway. Type “draytek” means the word is used as local ID. iname It means Dial-in Username. “iname=admin” means to set username as “admin”.
Page 775 It means to add a new route. It means to delete specified route. <index> It means the index number of the profile. Available index numbers: 1 ~ 32 <network ip>/<mask> Type the IP address with the network mask address. Vigor2860 Series User’s Guide...
Page 776 % Password % PPP Authentication : PAP/CHAP % VJ Compression : on % Pre-Shared Key % IPSec Security Method : AH % Schedule : 0,0,0,0 % Remote Callback : off % Provide ISDN Number : off Vigor2860 Series User’s Guide...
Page 777 Set PPTP VPN Service : On Please restart the router!! This command allows users to enable second subnet IP as VPN server IP. vpn 2ndsubnet on vpn 2ndsubnet off Parameter Description on/off It means to enable or disable second subnet. Vigor2860 Series User’s Guide...
Page 778 It means to display current setting status. default TCP maximum segment size for all the VPN connection will be set as 1360 bytes. Use it to specify the connection type and value of MSS. <connection type> 1~4 represent various type. Vigor2860 Series User’s Guide...
Page 779 # of free M-Buffer=529, minimum=529 leak=3 # of free S-Buffer=1199, minimum=1198, leak=1 # of free Msgid-Buffer=1024, minimum=1024 This command allows users to pass or block the multi-cast packet via VPN. vpn Multicast set <H2l/L2l> <index> <Block/Pass> Parameter Description Vigor2860 Series User’s Guide...
Page 780 [off] Parameter Description on/off on – the packets can pass through NAT. off – the packets cannot pass through NAT. > vpn pass2nat on % Packets would go through by NAT when VPN disconnect!! Vigor2860 Series User’s Guide...
Page 781 For PPPoE, the maximum number will be 1492. For PPTP/L2TP, the maximum number will be 1460. > wan mtu 1100 > wan mtu ? Static IP/DHCP (Max MSS: 1500) PPPoE(Max MSS: 1492) PPTP/L2TP(Max MSS: 1460) % wan ppp_mss <MSS size: 1000 ~ 1500> Vigor2860 Series User’s Guide...
Page 782 This command allows you to enable or disable the function of WAN forwarding. The packets are allowed to be transmitted between different WANs. wan forward [on] wan forward [off] Parameter Description on/off It means to enable or disable WAN forward. Vigor2860 Series User’s Guide...
Page 783 [init/init2/dial/pin][string] wan modem paponly [on/off] wan modem backup_wait [value] wan modem pipe [Int][Din][Dout] (for USB WAN3 only) wan modem wakeup [on/off/value] (for USB WAN3 only) wan modem vid [id] wan modem pid [id] wan modem status Vigor2860 Series User’s Guide...
Page 784 [show basic] wan vdsl[fbk_mode] Parameter Description show basic It means to display current VDSL status. fbk_mode It means to display current status of Fallback Mode used. Available modes to be set as fallback mode include, Auto Vdsl_only Vigor2860 Series User’s Guide...
Page 785 Use “all” to delete all. pass Set the password of LTE WAN. quota Set settings of SMS Quota Limit function. [-<command><parameter>l… Available commands with parameter are listed below: [...] means that you can type in several commands in one line. Vigor2860 Series User’s Guide...
Page 786 -p <password>: Set the Password / PIN. This setting is necessary if this function is enabled. -u <0/1>: Set whether to reply with Router system uptime. (0: no 1: yes) -v <0/1>: Set whether to reply with Router firmware version. (0: no 1: yes) Vigor2860 Series User’s Guide...
Page 787 [wan1/wan2/wan3/wan4][on/off/always_on] wan detect [wan1/wan2/wan3/wan4] target [ip addr] wan detect [wan1/wan2/wan3/wan4] target2[ip addr] wan detect [wan1/wan2/wan3/wan4] target_gw [1/0] wan detect [wan1/wan2/wan3/wan4] ttl [value] wan detect [wan1/wan2/wan3/wan4] interval [interval] wan detect [wan1/wan2/wan3/wan4] retry [retry] wan detect status Vigor2860 Series User’s Guide...
Page 788 > wan detect status WAN1: on, Target=192.168.1.78, TTL=255 WAN2: off WAN3: off WAN4: off WAN5: off > This command allows you to Enable/Disable for each WAN to join auto load balance member. wan lb [wan1/wan2/…] on Vigor2860 Series User’s Guide...
Page 789 -1: No need to add tag number. 1-4095: Available setting numbers used as tagged number. service type It means to specify the service type for VLAN. 0: Normal. 1: IGMP. vlan priority It means to specify the priority for the VALN setting. Vigor2860 Series User’s Guide...
Page 790 % Channel 4 uplink ifno: 3 % Channel 5 uplink ifno: 3 % Channel 6 uplink ifno: 3 % Channel 7 uplink ifno: 3 > This command allows you to configure the VLAN tag of WAN1 or WAN2. Vigor2860 Series User’s Guide...
Page 791 E.g., wan budget wan 1 rdate 5 10 If monthy mode is selected: WAN budget will be refreshed on 5th day at 10:00 in each month If periodic mode is selected: WAN budget will be refreshed every 5 Vigor2860 Series User’s Guide...
Page 792 Set the maximum times of ping failure during a Discovery. count: Available settings are 1 ~ 10. Default value is 3. > wan detect_mtu -w 2 -i 8.8.8.8 -s 1500 -d 30 -c 10 detecting mtu size:1500!!! mtu size:1470!!! Vigor2860 Series User’s Guide...
Page 793 The isolate setting will limit the wireless client's network capabilities to accessing the wireless LAN only. [MAC] format: xx-xx-xx-xx-xx-xx or xx:xx:xx:xx:xx:xx or xx.xx.xx.xx.xx.xx del [MAC] It means to delete a MAC address entry defined in the access control list. Vigor2860 Series User’s Guide...
Page 794 [ssid_num lan member] Parameter Description mode[value] It means to select connection mode for wireless connection. Available settings are: "11bgn", "11gn", "11n", "11bg", "11g", or "11b". mode show It means to display what the current wireless mode is. Vigor2860 Series User’s Guide...
Page 795 It means to isolate the wireless connection for LAN and/or Member. member] lan – It can make the wireless clients (stations) with remote-dial and LAN to LAN users not accessing for each other. member – It can make the wireless clients (stations) with the same Vigor2860 Series User’s Guide...
Page 796 Access Point and Station (in wireless client) invoke this function at the same time. 0: disable the function. 1: enable the function. > wl set MKT 2 on % New Wlan Setting is: % SSID=MKT % Chan=2 Vigor2860 Series User’s Guide...
Page 797 – scanning the AP based on SSID setting. channel - scanning the AP based on channel setting. mac - scanning the AP based on MAC address setting.. show [0/1/2/3] It is used to show AP list. 0 - display white list Vigor2860 Series User’s Guide...
Page 798 > wl stamgt set 1 60 60 > wl stamgt show 1 NO. SSID BSSID Connect time Reconnect time Draytek 00:11:22:aa:bb:cc 0d:0:58:26 0d:0:0 This command allows users to activate the function of VPN isolation. wl iso_vpn [ssid] [En] Parameter Description Vigor2860 Series User’s Guide...
Page 799 Que0_Ack Que1_Ack Que2_Ack Que3_Ack wl wmm enable SSID0 SSID1 SSID2 SSID3 wl wmm apsd value wl wmm show Parameter Description It means to set WMM for access point. It means to set WMM for wireless clients. Vigor2860 Series User’s Guide...
Page 800 QueIdx=0: BSSAifsn=3,BSSCwmin=4,BSSCwmax=10, BSSTxop=0,BSSACM=0 QueIdx=1: BSSAifsn=7,BSSCwmin=4,BSSCwmax=10, BSSTxop=0,BSSACM=0 QueIdx=2: BSSAifsn=2,BSSCwmin=3,BSSCwmax=4, BSSTxop=94,BSSACM=0 QueIdx=3: BSSAifsn=2,BSSCwmin=2,BSSCwmax=3, BSSTxop=47,BSSACM=0 AckPolicy[0]=0: AckPolicy[1]=0,AckPolicy[2]=0,AckPolicy[3]=0 This command allows you to configure wireless settings. wl ht bw value wl ht gi value wl ht badecline value wl ht autoba value Vigor2860 Series User’s Guide...
Page 801 Wireless restart....This command allows you to restart wireless setting. > wl restart Wireless restart....This command allows you to enable or disable wireless button control. wl btnctl [value] Parameter Description value 0: disable 1: enable Vigor2860 Series User’s Guide...
Page 802 IP addresses/Subnets will be eligible to pass through NAT and wake up the LAN client. You also need to set NAT rule for LAN client. wol up [MAC Address]/[IP Address] wol fromWan [on/off/any] wol fromWan_Setting [idx][ip address][mask] Vigor2860 Series User’s Guide...
Page 803 User name- type the user name that you want it to pass. IP_Address- type the IP address that you want it to pass. -l all Show online user. -l userl all – all of the users will be displayed on the screen. Vigor2860 Series User’s Guide...
Page 804 -q 200 It means to set data quota. e.g., -r 1000 It means to specify the data quota unit (MB/GB). e.g., -w MB It means to set schedule index. Available settings are” sch_idx1,sch_idx2,sch_idx3, and sch_idx4. Vigor2860 Series User’s Guide...
Page 805 -r 1000 It means to enable /disable time quota limitation for user account. 0:Disable 1:Enable It means to set data quota unit (MB/GB). > user account admin -d 1 Enable the [admin] data quota limited Vigor2860 Series User’s Guide...
Page 806 It is used to query any VigorAP which has been registered to APM (Central AP Management) in Vigor2860. Information related to the registered AP will be send back to Vigor2860 for updating the web page of Central AP Management. > apm clear ? Clear all clients ... done Vigor2860 Series User’s Guide...
Page 807 VigorAP. > apm profile clone 1 2 forcarrie (Done) > apm profile summary # Name SSID Security RateCtrl(U/D) - ---------------- ---------------- ------------ ------- ------ 0 Default DrayTek-LAN-A WPA+WPA2/PSK x DrayTek-LAN-B WPA+WPA2/PSK x 2 forcarrie DrayTek Disable Vigor2860 Series User’s Guide...
Page 808 0 – disable traffic limit. [4] – The forth number means the limit num of station. Available range is 3~64. [5] – The fifth number means the upload limit function. Type 1 – enable upload limit, Vigor2860 Series User’s Guide...
Page 809 5. Upload limit : 0 6. Download limit : 0 7. Enable disassociation by idle time : 0 8. Enable disassociation by Signal strength : 0 9. Traffic limit unit (upload) 10.Traffic limit unit (download) : 1 flag : 49 Vigor2860 Series User’s Guide...
Page 810 8d 03:03:12 syslog: [APM] Run AP Detection / Discovery. 8d 03:06:09 syslog: [APM] Send Rogue AP Detection data. 8d 03:13:21 syslog: [APM] Run AP Detection / Discovery. 8d 03:16:10 syslog: [APM] Send Rogue AP Detection data. 8d 03:16:41 kernel: 60:fa:cd:55:f5:ea had associated successfully Vigor2860 Series User’s Guide...
Page 811 % Show the APM AP Station Number data. % apm stanum AP_Index. ex : apm stanum 1 Idx Nearby(2.4/5G) Conn(2.4/5G) This command is used to display general setting of of VigorSwitch which connecting to Vigor router in LAN. swm show [LAN_port] Parameter Description Vigor2860 Series User’s Guide...
Page 812 Vigor router in LAN. swm post [LAN_port] Parameter Description LAN_port Specify the LAN port number (1 to 6). > swm post 1 Start post cfg to LAN (1) external switch with currect settings. Please wait a few seconds... Vigor2860 Series User’s Guide...
Page 813 System will cover the original VLAN settings on your VigorSwitch. Please backup the configuration file before you run this function. System also will select the physical connect port as trunk port and let it join each VLAN group. Vigor2860 Series User’s Guide...
Page 814 Before using such command, please use [swm show] to check valid VLAN index firstly. Vigor2860 Series User’s Guide...

Draytek Vigor2860 series User Manual

Part I Installation

Part II Connectivity

Part III Wireless LAN

Part IV Voip

Part V VPN

Part VI Security

Part VII Management

Part VIII Others

Part IX Troubleshooting

Quick Links

Related Manuals for Draytek Vigor2860 series

Summary of Contents for Draytek Vigor2860 series