Related Manuals for Hilti TE 2-A18
Summary of Contents for Hilti TE 2-A18
- Page 1 TE 2-A18 Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 07.07.2013 | Doc-Nr: PUB / 5140928 / 000 / 00...
- Page 2 This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado C US Printed: 07.07.2013 | Doc-Nr: PUB / 5140928 / 000 / 00...
- Page 3 Printed: 07.07.2013 | Doc-Nr: PUB / 5140928 / 000 / 00...
- Page 4 Printed: 07.07.2013 | Doc-Nr: PUB / 5140928 / 000 / 00...
-
Page 5: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the TE 2-A18 cordless rotary gether with the power tool. hammer. Ensure that the operating instructions are... -
Page 6: Description
Do not use the battery as a power source for other unspecified appliances. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. - Page 7 2.8 Items supplied as standard Power tool Side handle with depth gauge Operating instructions Hilti toolbox (optional) Cleaning cloth (optional) Grease (optional) 2.9 Additional items required for operating the tool B 18/1.6 Li-ion, B 18/2.6 Li-ion or B 18/3.3 Li‑ion battery. C 4/36‑90, C 4/36‑350, C 4/36‑ACS, C 4/36‑ACS TPS or C 4/36 battery charger.
-
Page 8: Insert Tools, Accessories
3 Insert tools, accessories Designation Description Hammer drill bits ∅ 4…16 mm (¹⁄₈" ... ⁵⁄₈") Anchor-setting tools C-type connection end Wood drill bits (auger bits) ∅ Max. 14 mm (¹⁄₂") Metal drill bits ∅ Max. 10 mm (³⁄₈") Keyless chuck 13 mm (¹⁄₂");... -
Page 9: Safety Instructions
Battery B 18/1.6 Li‑Ion B 18/2.6 Li‑Ion B 18/3.3 Li‑Ion Temperature monitoring Deep discharge protec- tion 5 Safety instructions NOTE If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) The safety rules in section 5.1 contain all general safety protected supply. - Page 10 preventive safety measures reduce the risk of 5.3 Additional safety precautions starting the power tool accidentally. 5.3.1 Personal safety d) Store idle power tools out of the reach of chil- a) Always hold the power tool securely with both dren and do not allow persons unfamiliar with the hands on the grips provided.
-
Page 11: Before Use
5.3.2 Power tool use and care flammable materials, and allow it to cool down. Contact Hilti Service after the battery has been a) Secure the workpiece. Use clamps or a vice to allowed to cool. - Page 12 DANGER (transport position). Use only the Hilti batteries and Hilti chargers listed If you disconnect a battery pack from the power tool under “Accessories”. for transport or storage, make sure that the contacts of the battery pack are not short-circuited.
-
Page 13: Operation
7 Operation Release the side grip clamping band by turning the grip counterclockwise. Pivot the side grip into the desired position. Adjust the depth gauge to the desired drilling depth. Tighten the side grip securely by turning the grip CAUTION section. -
Page 14: Care And Maintenance
Insert the battery. For reverse rotation, push the forward / reverse switch on Position the power tool and drill bit at the point the side of the power tool toward the grip in the direction where the hole is to be drilled. of the arrow. -
Page 15: Troubleshooting
Clean the sealing lip by wiping it in places subject to high ambient temperatures (e.g. at carefully and then grease it again lightly with Hilti grease. a window) as this has an adverse effect on battery life It is essential that the dust shield is replaced if the sealing and increases the rate of self-discharge. -
Page 16: Disposal
Dispose of defective batteries without delay. Keep them out of reach of children. Do not attempt to open or dismantle batteries and do not dispose of them by incineration. CAUTION Dispose of the batteries in accordance with national regulations or return them to Hilti. -
Page 17: Manufacturer's Warranty - Tools
Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information. - Page 18 Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 4118 | 0413 | 00-Pos. 3 | 1 Printed in China © 2013 Right of technical and programme changes reserved S. E. & O.