Page 1
HSM2HOST 2-Way Wireless Transceiver V1.0 Installation Manual WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
Choose a Mounting Location............................ 6 Connect the HSM2HOST ............................6 Enroll The HSM2HOST ............................6 Delete the HSM2HOST............................6 Test HSM2HOST Location for RF Interference....................... 6 Permanently Mount ..............................7 Other Options................................7 Wireless Device Setup and Programming ....................7 [804][000] Enroll Wireless Devices .........................
Can be wired up to 1000 ft. / 230 m from the main panel with 22 AWG wire • Connects to Corbus • Compatibility: The HSM2HOST is used with PowerSeries Neo alarm panels • Operating temperature: 0°C to +49°C (32-122°F) •...
Tamper The HSM2HOST has separate built-in wall and case tampers. The case tamper is disabled by default on the NA version (enabled on EU version). Section [804][810] option 3 enables or disables the case tamper. Enable or disable the wall tamper by fastening the breakaway wall tamper bracket securely to the wall using one of the supplied screws.
The HSM2HOST must be enrolled onto the alarm panel before any wireless devices can be enrolled. At initial power-up of the alarm panel When the alarm system is powered up for the first time, the first keypad or the HSM2HOST (if using a wireless keypad as the first keypad) can be enrolled. To do this: Once the HSM2HOST is wired to the alarm panel and power has been applied, power up a wireless keypad.
This section describes how to enroll and program wireless devices such as contacts, motion sensors and sirens on the alarm panel. 3.2.1 [804][000] Enroll Wireless Devices Once the HSM2HOST is installed and enrolled on the alarm panel, wireless devices can be enrolled using the following method: Enter Installer Programming section [804][000]: When prompted, either activate the device (see device installation sheet) to enroll immediately or enter a device ID number.
H S M 2 H O S T I n s t a l l a t i o n M a n u a l W i r e l e s s D e v i c e S e t u p a n d P r o g r a m m i n g 3.2.2 [804][001]-[716] Wireless Device Configuration To configure wireless devices: Enter Installer Programming section [804] then select one of the following sub-sections:...
H S M 2 H O S T I n s t a l l a t i o n M a n u a l W i r e l e s s D e v i c e S e t u p a n d P r o g r a m m i n g 3.2.5 [804][810] Wireless Options To program wireless options: Enter Installer Programming section [804][810].
NOTE: This option is not fully supported by LED and ICON keypads. 3.2.10 [804][999] Reset to Factory Defaults Selecting this option resets HSM2HOST programming to factory default settings. 3.2.11 [904] Placement Testing Wireless Devices This test is used to determine RF signal status for wireless devices and can be performed at a system keypad or at the individual device. These instructions pertain to testing at the keypad.
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s [810] HSM2204 4 High-Current Output Label (1 x 14 Characters) [820] Siren Label (1 x 14 Characters) [821] Repeater Label (1 x 14 Characters)
Page 13
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s [804][000] Wireless Device Enrollment –...
Page 14
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s [804][000] Wireless Device Enrollment –...
Page 15
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s [804][001]-[128] Configure Wireless Zones 1-128 (copy sheet as needed) Zone # Toggle Options...
Page 16
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s [804][551]-[566] Configure Wireless Sirens 1-16 (Copy sheet as needed) Siren # Sub-section...
Page 17
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s [804][601]-[632] Configure Wireless Keys 1-32 (copy as needed) [000] Wireless Key Partition Assignment (Default: 01) [001]-[005] Wireless Key Button Programming (Defaults: Key 1: 04, Key 2: 03, Key 3: 01, Key 4: 52, Key 5: 21)
Page 18
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s [804]-[701]-[716] Wireless Keypad Programming (copy as needed) Keypad #: [000] Partition...
Page 19
H S M 2 H O S T I n s t a l l a t i o n M a n u a l P r o g r a m m i n g W o r k s h e e t s 1 ____ 13 ____ 25 ____ 37 ____ 49 ____ 61 ____ 73 ____ 85 ____ 97 ____ 109 ____ 121 ____...
English. of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this EULA, DSC 7. LIMITED WARRANTY is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative. www.dsc.com 2 9 0 0 8 9 8 8 R0 0 1...