Table of Contents
Advertisement
Chapter 10
Function Mode
Metronome
This parameter has three settings: On, Rec or Off. The default setting is Off, or no metronome. If you choose On
the metronome sounds while playing or recording. To hear the metronome only while recording, choose Rec.
In Function Mode, press the Select▲ or ▼ button until the display reads
METRO: OFF (factory default). To change to On press the +Next button once. The
metronome sounds while playing or recording. To change to Rec press the +Next
button again. This allows you to hear the metronome only while recording. Pressing
the Prev- +Next button pair will reset the Metronome back to Off (factory default).
The Metronome setting is remembered across power cycles.
Rec Rhythm
This parameter controls whether a rhythm pattern plays during recording. The default for this parameter is Off. If you
record a song and want the rhythm pattern recorded as well, be sure to change this parameter to On.
Press the Select▲ or ▼ button until the display reads REC RHYTHM: OFF
(factory default). To change to On press the +Next button once. Press Prev- to
turn Rec Rhythm to Off.
The Rec Rhythm setting is remembered across power cycles.
Local Control
When you play the Andante CGP220 keyboard you hear the resident or "local" voices, because this parameter is
normally set to On. When using your Andante CGP220 with an external sequencer or computer, turn this setting to Off
to avoid creating a MIDI loop which may result in stuck notes or "echoes."
Auto Power Off
This energy-saving feature will automatically shut off power to the unit after a period of inactivity. Simply turning the
power switch off and on will power up the unit once again. This allows you to reduce overall power consumption, and
also extends the lifetime of the instrument. Press the Select▲ or ▼ button until the display reads AutoPowerOff.
Setting options are Enabled or Disabled.
Auto Power Off Time
With Auto Power Off Enabled, you may set the lenth of inactivity time until power is shut down. Use the Prev- +Next
buttons to select your setting. Options are 15 min, 30 min, 1 hour, 2 hours or 4 hours.
Once the AutoPowerOff inactivity period has begun, any human interaction (playing the keyboard, etc.) will reset the
timer.
Audio Input
The parameter enables or disables the audio input jack. In some situations, the user playing the Andante CGP220
may notice a high frequency noise when not using the Audio Input (that is, with no signal applied to the input jacks).
Setting Audio Input to Disabled will overcome this. The default setting for this parameter is Enabled. The chosen
setting will be remembered across power cycles.
page 30
Hard Reset (Restoring Factory Defaults)
This function resets the Andante CGP220 to the original factory default settings. All user changes, saved
Favorites, and user recorded songs are erased. This action cannot be undone.
METRO: OFF
If you want to cancel the Hard Reset and remain in Function Mode, press the Prev- button to confirm.
Press any other button to exit Function Mode.
There is an alternate method for a Hard Reset your Andante CGP220:
REC Rhythm:
OFF
OS/Objects Version
To check for possible updates to your operating system in Function Mode press the Select ▲ or ▼ buttons one
step past HARD RESET?. This will display the current operating software and objects version.
The display first shows the OS version, then the Object version. Visit the Kurzweil website (www.kurzweil.com) to
verify that your Andante CGP220 has the latest versions. These are located under the Downloads tab for the Andante
CGP220. Complete installation instructions are included in the downloaded files. A standard USB cable will be
required for this operation.
1. In Function Mode press the Select ▲ or ▼ buttons until the display reads HARD RESET?.
2. To perform the Hard Reset function press the +Next button once.
3. The display now reads CONFIRM?.
4. Press the +Next button again confirm and to reset the Andante CGP220. The unit will then erase its
user memory, restore all factory settings and reboot.
1. Hold the C8 key down while switching on the power.
2. Continue to hold C8 down until you see "RESETTING" (scrolling) in the display then release.
Chapter 10
Function Mode
page 31
Advertisement
Table of Contents
