Transportation Screws (Red) - Pioneer PD-F1004 Operating Instructions Manual

TROUBTESHOOTING
lncorrect operations are often mistaken for
trouble and malfunctions. lf
you think
that there
is something wrong with this component,
check
the
points below. Sometimes
the
trouble
may lie in
another component. lnvestigate the other
components and electrical appliances
being
used.
lf the trouble cannot be rectified even after exercising
the checks listed below,
ask
your nearest
PIONEER authorized
service center or your
dealer
to
carry
out
repair work.
Abnormal functioning of
this
unit may
be caused
by
static electr¡c¡ty,
or other external
interference.
To
restore normal operation, turn the
power
off and then on again,
or
unplug the
AC
power
cord and then
plug
it in
again.
24
<PRB
1
230>
En
o
Connect properly
o
Check
the power
and input settings
of
the
TV.
o
Clean dirt away.
o
Disconnect
the
PD-AP1
. (The On-Screen
Disc
Management operation
is
not
available
while the
PD-AP1
is
connected.)
o
Video cables are
connected incorrectly or
loosely.
o
lncorrect operation of the
TV set.
o
Pin
plugs and/or the W
input terminal are dirty
o
The
PD-AP1 is connected to this unit.
No picture.
o
Replace batteries.
o
Operate the remote control
unit
within
a range
of
about
7
meters
(23
feet) from the
remote
sensor, and within
angles
of
up
to
about
30
degrees.
o
Relocate remote
control unit or
remove
obstruction.
o
Dead batteries.
¡
Too far
from player or wrong
angle
r
Obstruction
between
player and remote control
unit.
Remote control
will
not
function
o
Turn off
POWER
of the player, or
move the
player away
from the
tuner.
o
lnterference
is being picked up
from the
CD
player.
FM
broadcast
has
noise
interf erence.
o
Replace the disc
o
Clean disc.
¡
Disc
has a bad scratch or
warp
¡
Disc
is
extremely
dirty.
With
certain discs, loud noise
is
produced, or play stops.
o
Connect to amplifier's
CD or AUX
terminals
Do
not
connect
to
PHONO terminals.
o
Clean away dirt.
o
lncorrect
connections.
o
Pin plugs and/or amplifier terminals
are
dirty
Sound is distorted, noise
rs
output.
o
Connect properly
¡
Check
the
settings
of
amplifier switches
and
sound volume controls.
o
Clean away dirt.
o
Press
>
or
tt.
.
lnsert
the
disc
correctly
with the label
side
rightward.
o
Audio
cables are connected incorrectly
or
loosely.
.
lncorrect
operation of stereo amplifier.
r
Pin plugs and/or amplifier
terminals are dirty
o
Player is in pause mode.
o
Disc is
inserted
the wrong
way.
No sound
¡
Remove
the three transportation screws. (See
page
4.)
¡
lnsert the
disc
correctly
with the label
side
rightward.
o
Clean
the
smudges
from the
disc and
then
play it
again.
o
Carefully wipe the
disc
with
the supplied
Elec-
trostatic charge removal sheet
(page g).
¡
The internal
mechanism
is
fixed with
transportation
screws.
o
Disc is
inserted
the wrong way.
o
Smudges, etc., on the disc
o
The
selected disc
has
an electrostatic charge
When playback
is
started,
it
stops
immediately.
Pauses or stops during playback.
o
Close
all
the
Racks and
the
front panel.
Then stop
playing
back
a
disc in
the
desired
Rack,
or start
playing
backadiscinanotherRack(formorethan
10
seconds).
o
Close
allthe
Racks and the front panel, and
wait
for
the Disc search to completely finish
or
more than 10 seconds after
finishing playback.
e
Connect the AC
power
plug securely to the wall
outlet.
o
A
disc in the desired Rack is being
played.
(The
RACK INDICATOR is blinking
)
o
A
disc
is being searched
or
10 seconds have
not elapsed since playback finished.
o
The
wal
AC
power
plug
is disconnected
from the
I
outlet.
The Rack
is not
opened when
EJ
ECT
button (A)
is pressed.
Remedy
Probable cause
Symptom