Page 1
Indirecte boiler Indirect calorifier Ballon échangeur ITS - 300 0310 115 Installatie-, Gebruikers- en Servicehandleiding Installation, User and Service Manual Notice d’installation, Mode d’emploi, Notice d’entretien Innovation has a name.
Page 3
ITS 300 Inhoudsopgave / Table of contents / Table des matières Deze handleiding bestaat uit 3 talen. 1 - NL Handleiding ITS 300 ......................5 2 - UK Manual ITS 300 ........................21 3 - FR Notice ITS 300 ........................39 This manual consists of 3 languages.
Page 5
A.O. Smith Water Products Company. A.O. Smith Water Products Company behoudt zich het recht voor de specificaties zoals vermeld in deze handleiding te wijzigen.
ITS 300 Technische specificaties 1.1 Vloerbelasting Houd in verband met het gewicht van het toestel rekening met de maximale vloerbelasting, zie de tabel (1.4 "Algemene gegevens"). 1.2 Watersamen- Het toestel is bedoeld om drinkwater op te warmen. Het drinkwater moet voldoen aan de stelling regelgeving voor drinkwater voor menselijke consumptie.
ITS 300 Installatie 2.1 Aansluitschema De figuur geeft het aansluitschema weer. Dit schema wordt gebruikt in de paragrafen waarin het eigenlijke aansluiten wordt beschreven. Legenda 2. inlaatcombinatie (verplicht) 3. T&P-ventiel (aanbevolen) 4. afsluiter (aanbevolen) 5. terugslagklep (verplicht) 6. circulatiepomp (optioneel) A.
Page 14
ITS 300 Let op Een inlaatcombinatie is verplicht. Monteer deze zo dicht mogelijk bij het toestel. Waarschuwing Tussen inlaatcombinatie en het toestel mag nooit een afsluiter of terugslagklep geplaatst worden. Warmwaterzijdig 2.2.2 Zie (B) in het aansluitschema (2.1 "Aansluitschema"). Opmerking Isolatie van lange warmwaterleidingen voorkomt onnodig energieverlies.
ITS 300 Onderhoud Let op Onderhoud mag alleen door een erkend service- en onderhoudsmonteur worden uitgevoerd. Bij elke onderhoudsbeurt dient de boiler waterzijdig onderhouden te worden. Het onderhoud dient in de volgende volgorde te worden uitgevoerd. 1. Onderhoud voorbereiden 2. Waterzijdig onderhoud 3.
Page 16
ITS 300 Werkvolgorde: 1. Draai de bouten van de reiningsopening los. 2. Verwijder de deksel en de pakking. 3. Inspecteer de tank en verwijder de losse kalkaanslag en verontreinigingen. 4. Indien de kalkaanslag niet handmatig verwijderd kan worden, dient ontkalkt te worden met een ontkalkingmiddel.
Indien binnen één jaar na de oorspronkelijke installatiedatum van een door A.O. Smith algemeen geleverde boiler, na onderzoek en ter uitsluitende beoordeling van A.O. Smith, blijkt dat een deel of onderdeel, met uitzondering van de tank, niet of niet juist functioneert ten gevolge van fabricage- en/of materiaalfouten, zal A.O.
Een claim gebaseerd op de gegeven garantie moet worden gedeponeerd bij de handelaar bij wie de boiler is gekocht of bij een andere handelaar die de producten van A.O. Smith Water Products Company verkoopt. Het onderzoek van de boiler bedoeld in de artikelen 1 en 2 zal plaatsvinden in een laboratorium van A.O.
Page 21
Any brand names mentioned in this manual are registered trademarks of their respective Trademarks owners. A.O. Smith Water Products Company accepts no liability for claims from third parties arising Liability from unauthorised use, use other than that stated in this manual, and use other than in accordance with the General Conditions registered at the Chamber of Commerce.
Page 23
Preparation for maintenance ....................33 Water-side maintenance ....................33 Warranty ..........................35 General warranty ........................ 35 Tank warranty ........................35 Conditions for installation and use ..................35 Exclusions .......................... 35 Scope of warranty ......................36 Claims ..........................36 Obligations of A.O. Smith ....................36...
ITS 300 Technical specifications 1.1 Floor load Allow for the water heater's weight and the maximum floor load; refer to the table (1.4 "General specifications"). 1.2 Water composition The water heater is intended for heating drinking water. The drinking water must comply with the regulations governing drinking water for human consumption.
ITS 300 Installation 2.1 Installation diagram This figure shows the installation diagram. This diagram is referred to in the sections describing the actual connection procedure. VENTED UNVENTED Legend 1. pressure relief valve 11. service stop valve A. cold water supply (mandatory if mains water 12.
ITS 300 2.2 Unvented water Warning connections The installation should be carried out by a competent person, in compliance with general and locally applicable regulations. Cold water side 2.2.1 See (A) in the installation diagram (2.1 "Installation diagram"). 1. Fit an approved stop valve (4) on the cold water side as required by the applicable regulations.
Page 31
ITS 300 2.3.2 Hot Water side See (B) in the installation diagram (2.1 "Installation diagram"). Note Insulating long hot water pipes prevents unnecessary energy loss. 1. Optional: fit a temperature gauge (12) so you can check the temperature of the tap water.
ITS 300 Maintenance Warning Maintenance may only be carried out by a competent person. At each service, the water heater undergoes maintenance on water side. The maintenance must be carried out in the following order. 1. Preparation for maintenance 2. Water-side maintenance 3.
Page 34
ITS 300 Work order: 1. Undo bolts from the cover. 2. Remove cover and the gasket. 3. Inspect the tank and remove the loose scale deposits and contamination. 4. If the scale cannot be removed by hand, descale the water heater with a descaling agent.
Warranty 4.1 General warranty If within one year of the original installation date of a water heater supplied by A.O. Smith, following verification, and at the sole discretion of A.O. Smith, an assembly or part (with exclusion of the tank) proves to be defective or fails to function correctly due to manufacturing and/or material defects, then A.O.
Certificate. Under the terms of the supplied warranty, A.O. Smith is not liable for damage to persons or property caused by (assemblies or parts, or the glass-lined steel tank of) a (replacement)
Page 39
écrit préalable de A.O. Smith Water Products Company. A.O. Smith Water Products Company se réserve le droit de modifier les spécifications de ce manuel d'instructions. Toutes les marques mentionnées dans ce manuel d'instructions sont des marques Marques de commerce déposées par les fournisseurs concernés.
Page 41
Entretien côté eau ......................49 Garantie ..........................51 Garantie générale ......................51 Garantie sur la cuve ......................51 Conditions d'installation et d'utilisation ................51 Exclusions .......................... 52 Portée de la garantie ......................52 Réclamations ........................52 Obligations de A.O. Smith ....................52...
ITS 300 Spécifications techniques 1.1 Charge maximale Tenez compte de la charge maximale exercée sur le sol par le poids de l'appareil, voir le au sol de l'appareil tableau (1.4 "Données générales"). 1.2 Composition de L'appareil est destiné à réchauffer de l'eau potable. L'eau potable doit être conforme aux l'eau régulations d'eau potable pour la consommation humaine.
ITS 300 Installation 2.1 Schéma de raccor- Cette illustration représente le schéma de raccordement. Ce schéma est utilisé dans les dement paragraphes suivants contenant une description du raccordement proprement dit. Légende 2. groupe de sécurité (obligatoire) 3. soupape thermique (recommandée) 4.
Page 48
ITS 300 Attention Un groupe de sécurité est obligatoire. Montez-le le plus près possible de l'appareil. Avertissement Entre la combinaison d'entrée et l'appareil, vous ne pouvez jamais monter de vanne d'arrêt ou de clapet anti-retour. Côte eau chaude 2.2.2 Voir (B) du schéma de raccordement (2.1 "Schéma de raccordement").
ITS 300 Effecteur l'entretien Attention L'entretien ne peut êntre effectué que par un professionnel de la maintenance ou de l'entretien agréé. A chaque entretien, l'appareil doit être contrôlé côté eau et côté gaz. L'entretien doit s'effectuer dans l'ordre suivant. 1. Préparer l'entretien 2.
Page 50
ITS 300 Ordre du travail : 1. Faites tourner les boulons de l’ouverture de nettoyage. 2. Éliminez le couvercle et le joint. 3. Inspectez le réservoir. Éliminez la couche de calcaire accumulée et les saletés. 4. Si la couche de calcaire ne peut être éliminée manuellement, il convient de retirer le calcaire avec un détartrant.
Si, moins de trois ans après la date initiale de l'installation d'un chauffe-eau livré par cuve A.O. Smith, après examen par et sur l'appréciation exclusive de A.O. Smith, la cuve en acier thermo vitrifié présente des fuites suite à une formation de rouille ou de corrosion du côté de l'eau, A.O.
4.5 Portée de la Les obligations de A.O. Smith conformes à la garantie accordée se limite à la livraison garantie gratuite de l'entrepôt des pièces ou parties à remplacer ou de l'appareil à remplacer. Les frais de transport, de travail, d'installation et autres frais relatifs au remplacement ne viennent pas à...