Hilti dx 2 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Power Tool
  5. dx 2
  6. Operating instructions manual

Hilti dx 2 Operating Instructions Manual

Powder-actuated fastening tool
Hide thumbs Also See for dx 2:
Table of Contents

Advertisement

Quick Links

See also: Operating Instructions Manual
Printed: 14.08.2014 | Doc-Nr: PUB / 5193679 / 000 / 00
DX 2
Operating instructions
Mode d'emploi
Manual de instrucciones
Manual de instruções
en
fr
es
pt

Advertisement

Table of Contents
loading

Related Manuals for Hilti dx 2

Summary of Contents for Hilti dx 2

  • Page 1 DX 2 Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 14.08.2014 | Doc-Nr: PUB / 5193679 / 000 / 00...
  • Page 2 Printed: 14.08.2014 | Doc-Nr: PUB / 5193679 / 000 / 00...
  • Page 3 Printed: 14.08.2014 | Doc-Nr: PUB / 5193679 / 000 / 00...
  • Page 4 Printed: 14.08.2014 | Doc-Nr: PUB / 5193679 / 000 / 00...
  • Page 5 Printed: 14.08.2014 | Doc-Nr: PUB / 5193679 / 000 / 00...
  • Page 6 Printed: 14.08.2014 | Doc-Nr: PUB / 5193679 / 000 / 00...

  • Page 7: Table Of Contents

    1.1.2 Requirements to be met by users quality. a) The tool is intended for professional use. Use of cartridges of inferior quality in Hilti tools may lead b) The tool may be operated, serviced and repaired to a build-up of unburned powder, which may explode only by authorized, trained personnel.
  • Page 8 Use the fasteners only within the recommended repaired or replaced properly at a Hilti service temperature range. Always observe the informa- center unless otherwise indicated in the operat- tion given in the operating instructions. Plastic ing instructions.

  • Page 9: General Information

    Make a note of equipment or other property. this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative NOTE or service department. Draws attention to an instruction or other useful informa- tion.

  • Page 10: Description

    The tool may not be used in an explosive or flammable atmosphere unless it has been approved for use under these conditions. To reduce the risk of injury use only genuine Hilti fasteners, cartridges, accessories and spare parts or those of equivalent quality.

  • Page 11: Accessories, Consumables

    4 Accessories, consumables NOTE For information about further accessories and fasteners for use with the tool, please contact your local Hilti representative. Accessories and cleaning set Designation Cleaning set, Hilti lubricant spray, spare parts pack, operating instructions, spall guard Standard accessories...

  • Page 12: Guidelines

    7.1 Fastening guidelines These guidelines must be observed at all times. NOTE For detailed information, please ask your local Hilti sales and service office for a copy of the applicable technical guidelines or national technical regulations. 7.1.1 Minimum distances and spacing Minimum distances and spacing when fastening to steel min.

  • Page 13: Operation

    WARNING 8.5 Cycling the tool 5 Never drive fasteners into existing holes unless this CAUTION is recommended by Hilti (e.g. DX‑Kwik). Do not use a swinging movement to cycle the tool (piston return and cartridge transport). The swinging CAUTION movement may lead to injury or cause damage to the If the tool has overheated, allow it to cool down.

  • Page 14: Care And Maintenance

    (after driving parts of the tool. This may lead to malfunctions. Use approx. 3,000 nails). only Hilti lubricant spray or a product of comparable Use the appropriate brushes to clean the individual parts: quality.

  • Page 15: Troubleshooting

    Spray the cleaned parts lightly with the Hilti lubricant be in alignment with the opening for the catch. spray supplied. Use only Hilti lubricant spray or a product Press the catch into the opening and turn the annular of comparable quality.
  • Page 16 See section: 9.3 Servicing the tool If the tool cannot be disassembled, contact your local Hilti Center. The cartridge strip melts. The tool is pressed against the work- Fire the tool sooner after pressing it ing surface for too long before firing.
  • Page 17 Clean the tool and remove any loose cartridges. If the tool cannot be disassembled contact your local Hilti Center. The piston gets stuck in the The fastener is too short. Use a longer fastener. base material / fastener is driven too deeply.
  • Page 18 Fault Possible cause Remedy Damaged nail head. Driving power is too high. Use a less powerful cartridge. Application limit exceeded (very hard Use a nail with a higher application material). limit. The piston is damaged. Change the piston. The nail doesn’t penetrate Driving power is too low.

  • Page 19: Disposal

    11 Disposal Most of the materials from which Hilti tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back old tools and appliances for recycling. Ask Hilti customer service or your Hilti representative for further information.

  • Page 20: Health And Safety Of The Operator

    15 Health and safety of the operator 15.1 Noise information Powder-actuated fastening tool Type DX 2 Model Serial Caliber 6.8/11 Application Fastening 20 mm ( ¾") laminated wood (plywood) to concrete (C40) with the X-U47 P8 Declared measured values of noise characteristics according to 2006/42/EC Machinery Directive in conjunction...
  • Page 21 Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 4344 | 0714 | 00-Pos. 3 | 1 Printed in Taiwan © 2014 Right of technical and programme changes reserved S. E. & O.

Table of Contents