Repairs; Spare Parts; Accessories - Felker TILE MASTER XL TM1-XLHT Operating Instructions And Parts List Manual

11

REPAIRS

We carry out all repairs in the shortest possible time and at
the most economical prices. (See front page for address
and phone numbers) Contact your authorized FELKER®
dealer concerning maintenance and repairs.
13 TILE CUTTING ACCESSORIES
ANGLE GUIDE
Parts List:
Diag. Part No. Qty.
1 161479 1
2 050107 1
3 050105 1
4 050106 1
5 050103 1
6 020598 2
7 051020 1
8 020598 1
9 ———— 1
RIP GUIDE: P/N 051000 - The Rip Guide is a standard
accessory supplied with every tile saw. It is used to provide
a repeatable position for rip cuts until relocated. The Rip
Guide clamps to the machined backstop of the conveyor cart.
ADJUSTABLE PROTRACTOR: P/N 051010 - The Protractor
can be used to rip cut known angles. The protractor clamps to
the backstop.
ANGLE GUIDE : P/N 051020 - This is a non-adjustable
miter used to quickly position the tile at 45 degrees; either on
the left or right side. It is often used for repeated diagonal rip
cuts. The Angle Guide clamps to the backstop.
BULLNOSE MITERING GUIDE: P/N 051030 - This is a
fixed guide that positions the tile for a 45 degree miter cut.
The Mitering Guide clamps to the backstop.
PRECISION MITERING JIG: P/N 161480 - This is a 45 degree
fixture that has an adjustable clamp to hold the tile while miter
cutting. The Mitering Guide clamps to the backstop.
PROTRACTOR PRECISION MITERING GUIDE
Description
Frame, Miter
Bar, Locking
Clip, Stop
Spring
Knob
Screw, Thumb, 1/4" - 20 x 1"
°
Miter Assy, 45
Screw, Thumb, 1/4" - 20 x 1"
Protractor Head
12

SPARE PARTS

For quick supply of spare parts and to avoid any lost time, it
is essential to quote the data on the manufacturers plate
fixed to the machine and the part number(s) and description
to be replaced with every order.
Diag. Part No. Qty.
10 ———— 1
11 020011 1
12 020244 1
13 020598 1
14 051010 1
15 020598 1
16 051030 1
17 051041 1
18 050102 1
BOOMERANGLE: P/N 169525 - This plastic accessory
holds the tile at 45 degrees; locating two edges of the tile.
Useful for diagonal cuts or uniformly cutting off corners. The
Boomerangle clamps to the backstop with two thumb screws.
FOLDING STAND: P/N 051041 - This stable, one piece
stand brings a FELKER® tile saw to standing level for ease
of work. The stand conveniently folds flat for storage and
transporting.
The instructions for use and spare parts found in this
document are for information only and are not binding.
As part of our product quality improvement policy, we
reserve the right to make any and all technical
modifications without prior notice.
The manufacturer accepts no
responsibility caused by unsuitable
use or modifications.
BULLNOSE FOLDING STAND
Description
Protractor Arm
Bolt, Carriage, 1/4-20 x 5/8"
Wing Nut, 1/4-20
Screw, Thumb, 1/4-20 x 1"
Protractor Assy
Screw, Thumb, 1/4" - 20 x 1"
Holder Assy, Bullnose
Stand, Tile Saw
Support Assy, Miter Frame
17