EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. SUPPLIED WITH A COPY OF THIS MANUAL. FAMILIAR WITH THE SAFETY WARNINGS. FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH. FOLLOW INSTRUCTIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION. CONTENTS Symbol Definitions ...3 - 4 Decal Descriptions and Locations...5...
Symbols Definitions Symboles Definición De Simbolos • Please read the instructions for use prior to operating the machine for the first time. • Avant toute mise en service, lire attentivement la notice et se familiariser avec la machine. • Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina. •...
Page 4
• Wear Appropriate Clothing • Port obligatoire de la tenue appropriée • Usar Ropa Adecuada • Machinery Hazard, Keep Hands And Feet Clear • Danger! Rester à distance de la machine • Máquina Peligrosa - Mantenga Manos Y Pies Alejados De La Máquina •...
WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition. wear safety approved hearing, eye, head and respiratory protection.
Page 9
DO NOT This saw was designed for certain applications only. DO NOT modify this saw or use for any application other than for which it was designed. If you have any questions relative to its application, DO NOT use the saw until you have written Electrolux Construction Products and we have advised you.
INDICATION INFORMATION INSTRUCTION PROHIBITION Your FELKER® tile saw is a ruggedly constructed unit engineered to give long, satisfactory performance. Simple, daily maintenance and care will add to the life and productivity of your tile saw. • •...
Assembly Tools required: four wrenches supplied (2 allen type) • Place saw frame with cart into water tray. (Fig 4) • Feed the powerhead assembly onto the arm of the saw frame through the opening in the back of the powerhead.
Make sure that the supporting surfaces of the Blade, the Flanges and the arbor are clean. ELECTRICAL CONNECTIONS • Use a grounded circuit. • Use a GFCI when wet sawing. • Use the correct plug and outlet. • Check that the main voltage is identical to that of the machine.
NOTE: THERE ARE NO ADJUSTMENTS TO WATER TRAY Alignment Procedures Your TM-75 tile saw is factory assembled and aligned prior to shipment to ensure accurate cuts when your saw is delivered. However, since FELKER ® cannot control rough handling during shipping, it is suggested that the alignment be checked.
Let the machine cool down!! FOR LONGEST LIFE AND BEST PERFORMANCE • Always clean the saw after every use. • Wipe all of the exterior sediment or dirt off the motor. Never spray water directly onto the motor! •...
Check to see if the water pump is clean and free of any chips, debris, clogging, etc. SAW WON’T CUT STRAIGHT • Check to see if saw frame or rolling guide bar is bent. • Check to see if the support for the cutting table is bent.
Page 17
542190504 Replaced Inner Flange, P/N 185218, Spacer, P/N 185216, and Seal, P/N 185215 Outer Flange, P/N can be used for units before Serial Number 417841, but 542190504 must be removed and discarded. Seal (185215) DIAGRAM 1 --- TM-75 PARTS LIST 417841) (See Note 1) 417841) (See Note 1) 417841)
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Please record the Date of Purchase and the Serial Number of your saw in the space below. (The serial number is located on the side of the motor.) When ordering service items, please have this information available.
Page 20
Corporate Office ...913-928-1000 Customer Service FAX ...800-825-0028 Corporate Office FAX ...913-438-7951 Customer Service, Int’l...913-928-1258 www.felkersaws.com From the Electrolux Group. The world’s No.1 choice. Felker Latin America, Mexico, Caribbean, Central and South America 17400 West 119th Street Olathe, Kansas 66061 Phone ...913-928-1255 FAX...913-438-7938...