Related Manuals for Pyle PLCMTR71
Summary of Contents for Pyle PLCMTR71
- Page 2 PLCMTR ‐ Commercial Grade Camera System www.pyleaudio.com Please read instructions carefully before installation and use. Installation should be performed by a professional installer. To ensure your safety, the driver should not watch videos or operate features on the monitor while driving. There are no serviceable parts in this unit, do not disassemble or try to repair this unit. If the unit malfunctions please return to your vendor or send to a Pyle repair facility. Please observe and obey the local laws and regulations when installing the unit. Upon Installation, please make sure as to not to interfere with any of the vehicle's safety features, wiring, components, etc. We are not responsible for any damages, injury, malfunctions or otherwise noted due to faulty or non‐professional installation. Connection Connect the camera’s threaded locking 4‐pin cable connectors into the female receiving connection of the included 4‐pin extension cable. The extension cable then connect to your compatible video monitors with 4‐pin receiving connector. The threaded locking cable connectors of the camera serve to provide power and video for the camera. Please remember to disconnect your vehicle's battery prior to any connection / installation. Use the included wiring harness to provide power and video signals to your monitor. There are colored wires to assist in the video camera system setup. See the wiring diagram for connections between cameras, monitor and your vehicle When turning the vehicle's ignition key or turning to the accessory or ON position, power is supplied to the camera system through the control box and the monitor will be in stand‐by mode. ...
-
Page 3: Wiring & Connection
PLCMTR ‐ Commercial Grade Camera System www.pyleaudio.com Wiring & Connection *When the Green ‐ Reverse Trigger ‐ is connected, the system will automatically revert to this connection once the vehicle is placed into reverse gear. This is Red: Power 12/24V ... -
Page 4: Monitor Controls
PLCMTR ‐ Commercial Grade Camera System www.pyleaudio.com The video monitor is provided power and camera video signals via the video and power wiring harness. From the monitor, you will be able to control Ch. 1, Ch. 2, input video cameras (V1, V2,). The power and video wiring harness includes an RCA (video) connector for you to install an additional video input source. Monitor Controls 1 Power 2 V1 / V2 3 '‐' Down Adjustment 4 Menu 5 '+' Up Adjustment *Please note, in cold weather and low temperatures, the display monitor may require some time to 'warm ... - Page 5 PLCMTR ‐ Commercial Grade Camera System www.pyleaudio.com 1. Set the mount stand in the desired location, then use screws to secure the mount stand into location. Please make sure as to set a location free from vehicle obstruction including any wiring, or location where it may obstruct the driver's view, driving conditions, etc. 2. Attach the metal buckle piece on top of the fan shaped mount stand, and slide it into the receiving slot in back of the display monitor assembly. This metal buckle should slide in and up to the monitor assembly. 3. Set the desired position/height of the buckle into the monitor assembly. 4. Tighten the clamp‐style knob in the back of the stand mount to secure the monitor in the desired position. 5. The angle / tilt position of the stand mount is also adjustable. Located toward the base of the stand mount is another clamp‐style knob. *Be sure to mount the video monitor from speakers or other devices which may distort the output display. Keep the monitor away from the speaker's or other device's magnetic field. *Install the monitor on a surface that can bear the capacity of over 9 lbs. *Don't install the monitor in the line of ventilation areas (keep away from extreme hot and extreme cold temperatures). *The monitor is not waterproof, avoid exposure to excess liquids or harsh cleaning chemicals/detergents. *Holes in the back of the display monitor serve as ventilation ducts. To ensure operation of the unit, and protect from overheating, these holes must not be blocked, to reduce risk of electric shock or fire. Model: PLCMTR71 Weatherproof Rearview Backup Camera & Monitor Video System, Commercial Grade, 7'' Monitor, Dual DC 12‐24V for Bus, Truck, Trailer, Van Camera: Includes (1) Universally Mountable Camera Commercial Grade Camera & Monitor Video System Weatherproof Rearview Camera System Includes All Necessary Cables & Wiring Marine Grade Construction, IP68 Rating Reverse Image (Backup Camera) Ability Built‐in Night Vision Illumination LEDs Used for Parking, Docking, Driving Safety Low Lux Light Performance Min. Illumination: 0.2Lux Monitor: Image sensor: Color CMD 7'' TFT/LCD Active Matrix Video Monitor Effective Pixels: 580 x 540 ...