Watching Tv; Turning The Tv On/Off; Initial Auto Installation; Checking Signal Information - Sharp LC-40LE660X Operating Instructions Manual

Watching TV

Turning the TV on/off

Turning on/off the power
• To turn on the power
Press POWER on the TV. (After a few seconds, an image
appears with sound.)
• To turn off the power
Switch it off by pressing POWER on the TV.
Standby mode
• To standby mode
If the TV is switched on, you can switch it to standby by
pressing POWER on the remote control.
• Switching on from standby
From standby, press POWER on the remote control.
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the AC outlet.
• Minor power is consumed when the unit is in standby
mode.

Initial auto installation

When the TV powers on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menu and make the necessary settings
one after another.
1
Press POWER on the TV.
• The initial auto installation wizard appears.
2
Press a /b to select your country channels listed
on the screen, and then press ENTER.
Press a /b to select the desired language, and
then press ENTER.
Press a /b to select "HOME" or "STORE", and
then press ENTER.
HOME:
• "STANDARD" will be the default value for the "AV mode"
setting.
STORE:
• "DYNAMIC (FIXED)" will be the default value for the
"AV mode" setting. If the "AV mode" is changed, the TV
will automatically switch back to "DYNAMIC (FIXED)"
when there is no further change to TV setting for 30
minutes.
• The confi rmation screen appears only when selecting
"STORE". Press a /b to select "Yes" or "No".
• To change the STORE mode to HOME mode, please
refer to page 11 to reset the unit.
* Press a /b to select "DTV", "ATV" or
"DTV + ATV", and then press ENTER.
• Auto installation will be executed.
• You do not need to do anything during the auto search.
• If you select "Others" country, some of DTV channel
may not tune properly.
- 6
LC-406070LE660X_EN_GXX.indd 6 LC-406070LE660X_EN_GXX.indd 6

Checking Signal information

If you install a DVB-T2 antenna for the fi rst time or
relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking
the antenna setup screen.
COLOUR COLOUR
ADJ. ADJ.
(FREEZE) (FREEZE)
1
Press MENU and the MENU screen displays.
2 Press c / d to select "

" (Programme setup).

3
Press a /b to select "Digital setting", and then
press ENTER.
4 Press a /b to select "Signal information", and
then press ENTER.
• The "Signal information" screen will appear.

Auto installation

You can run auto installation again, even after setting
up the preset channels.
1
Press MENU and the MENU screen displays.
2 Press c / d to select "
" (Programme setup).
3 Press a /b to select "Auto installation", and then
press ENTER.
If you have already set the password, enter it here.
• See page 8 for setting a password.
4
Press a /b to select your country channels listed
on the screen, and then press ENTER.
Press a /b to select the desired language, and
then press ENTER.
Press a /b to select "DTV", "ATV" or
*
"DTV + ATV", and then press ENTER.
You do not need to do anything during the auto
search. Press MENU to exit.
*
NOTE
• In the setting of some country, selecting of "DTV", "ATV" or
"DTV + ATV" may not be shown.
• A region or service selection screen may display depending
on the country settings or cable providers selections. Follow
the screen prompts to make the selections.
Programme setup
Digital setting
You can reconfi gure DTV services settings
automatically or manually.
1
Press MENU and the MENU screen displays.
2 Press c / d to select "
" (Programme setup).
3
Press a /b to select "Digital setting", and
then press ENTER. If you have already set the
password, enter it here.
• See page 8 for setting a password.
4 Press a /b to select the desired menu item, and
then press ENTER.
H Auto search
Use this menu to add new services automatically
after auto installation has been completed.
NOTE
• A region or service selection screen may display depending
on the country settings or cable providers selections. Follow
the screen prompts to make the selections.
H Manual search
Add new services within a specifi ed frequency band.
• Press c / d to select the frequency and then press ENTER.
Analogue setting
You can reconfi gure the TV channel settings
automatically or manually using Auto search,
Manual adjust or Programme edit.
H Auto search
You can also automatically search by performing
the procedure below. This is the same function as
programme auto search in auto installation.
1
Press MENU and the MENU screen displays.
2 Press c / d to select "
" (Programme setup).
3 Press a /b to select "Analogue setting", and
then press ENTER. If you have already set the
password, enter it here.
• See page 8 for setting a password.
4
Press a /b to select "Auto search", and then
press ENTER.
You do not need to do anything during the auto
search. Press MENU to exit.
H Manual adjust
You can set some channel items manually.
1
Repeat steps 1 to 3 in Auto search.
2
Press a /b
o select "Manual adjust", and then
t
press ENTER.
3
Press a /b to select your desired item, and then
press c / d to adjust the settings.
Item Description
Storage to Save programme to your desired
[1~99] channel number. Press R to save.
Sound system Select the optimum sound system
(Broadcasting system) to receive.
(B/G, D/K, I, M)
Colour system Select the optimum colour system to
receive. (PAL, SECAM, NTSC)
Current CH Select the channel you want to edit.
• Selected channel will be automatically
refl ected in the background.
Search Start searching from current channel.
• Instead of pressing c/d to adjust the
frequency, you can set by directly entering
the frequency number of the channel with
0 — 9.
Press R to save.
Fine-tune Tune the frequency of the stored
channel to your desired position.
• Adjust while checking the background
picture as a reference.
Press R to save.
NOTE
• The frequency shown below the On-Screen Display shows
the real-time frequency of the displayed channel.
9/2/2014 9:23:35 AM 9/2/2014 9:23:35 AM