Using A Smartphone With The Tv; Teletext Function; Using A Pc; Pc Compatibility Chart - Sharp LC-40LE660X Operating Instructions Manual

Using a Smartphone with
the TV
This function enables you to connect the TV to a
smartphone that supports Mobile High-Defi nition
Link (MHL) using an MHL-compatible cable.
To connect the TV to your MHL-compatible
smartphone, be sure to use an MHL-compatible
cable (commercially available).
• You can view pictures and video on a large screen.
• You can play back music fi les.
HDMI 2
MHL
2
MHL-compatible cable
(DC5V 900mA)
INPUT 2 terminal (Rear side)
NOTE
• An MHL-compatible portable device is required to use this
function. Connect the device to the INPUT 2 terminal.
• This product incorporates MHL 2.
H Auto power on
When an MHL-compatible device is connected to
the TV, the TV turns on automatically.
• This function operates when "Link operation" is set to "On".
(See page 8.)
H Auto input selection
When an MHL-compatible device is connected
while the TV is on, the input mode is selected
automatically.
• This function operates when "Link operation" is set to "On".
(See page 8.)
H Operation using the remote control
The remote control of the TV can be used to operate
a portable device.
• a /b/ c / d , ENTER, 0 – 9, etc.
• The operations vary depending on the connected
equipment and content being viewed.
• Colour (Red/Green/Yellow/Blue) may be available to
control play/pause/fast forward/back forward function.
• The illustrations used throughout this manual are based
on LC-60LE660X.
- 14
LC-406070LE660X_EN_GXX.indd 14 LC-406070LE660X_EN_GXX.indd 14

Teletext function

What is Teletext?
Teletext broadcasts pages of information and
entertainment to specially equipped television sets.
News, weather reports, sports information, stock
exchange prices and programme previews are
among the many services available.
Turning on and off Teletext
1
Select a TV channel or external input source
providing the Teletext programme.
2
Press m to display the Teletext.
3
Each time you press m , the screen switches as
shown below.
TELETEXT TELETEXT
NOTE
• If you select a programme with no Teletext signal,
"No Teletext available." is displayed.
• The same message displays during other modes if no
Teletext signal is available.
• New Zealand delivery model can receive MHEG data
broadcasting.
Button functions
Buttons Description
CH ( r / s )
Increase or decrease the page number.
Colour (Red/ You can select a group or block of
Green/Yellow/ pages displayed in the coloured brackets
Blue) at the bottom of the screen by pressing
the corresponding Colour (Red/Green/
Yellow/Blue) on the remote control
unit.
0 – 9 Directly select any page from 100 to 899
by using 0 – 9.
k (Reveal
To reveal hidden information such as an
hidden for answer to a quiz.
TELETEXT)
3 (Hold)
To stop updating Teletext pages
automatically or release the hold mode.
[ (Subtitle for
Display the subtitle during Teletext page.
TELETEXT)
• Subtitle will not be displayed when the
service does not contain subtitle information.
NOTE
• Teletext can display only when it is sent by a network. Not
used to convert between languages.

Using a PC

PC compatibility chart

Horizontal
Resolution
Frequency
640 g 480
VGA 31.5 kHz
800 g 600
SVGA 37.9 kHz
1024 g 768
XGA 48.4 kHz
1360 g 768
WXGA 47.7 kHz
1080P 1920 g 1080 67.5 kHz
DDC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, Inc.
VGA, SVGA, XGA and WXGA are registered trademarks of International Business Machines Corporation.

PC Control of the TV

• When a programme is set, the TV can be controlled from
the PC using the RS-232C terminal.
The input signal (PC/video) can be selected, the volume
can be adjusted and various other adjustments and settings
can be made, enabling automatic programmed playing.
• Attach an RS-232C cable cross-type (commercially
available) to the Din/D-sub RS-232C for the connections.
NOTE
• This operation system should be used by a person who is
accustomed to using PCs.
Communication conditions
Set the RS-232C communications settings on the
PC to match the communications conditions of the
TV. The communications settings of the TV are as
follows:
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Communication procedure
Send the control commands from the PC via the
RS-232C connector.
The TV operates according to the received command
and sends a response message to the PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before
sending the next command.
Vertical VESA Analogue
Digital (HDMI)
Frequency Standard (D-Sub)
✔ ✔
60 Hz
✔ ✔
60 Hz
✔ ✔
60 Hz
✔ ✔
60 Hz
✔
60 Hz
Command format
Eight ASCII codes e CR
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digits Parameter 4-digits Return code
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0 – 9, space, ?
Parameter
Input the parameter values, aligning left, and fi ll with
space(s) for the remainder. (Be sure that four values
are input for the parameter.)
When the input parameter is not correct, "ERR"
returns. (Refer to "Response code format".)
0 0 0 0 9 a
Response code format
Normal response
O K
Return code (0DH)
Problem response (communication error or incorrect
command)
E R R
Return code (0DH)
9/2/2014 9:23:40 AM 9/2/2014 9:23:40 AM
✔
✔
✔
✔
✔
3 0