Advertisement
5HSODFLQJWKH%DWWHU\
A . Grasp the transmit switch, lift the transmitter module out of
the base and turn it over. The bottom side can now be
viewed.
B . Slide the old battery from
under the clip in the opposite
direction to the arrow shown
in Figure 4.
C. Hold the 3-volt replacement
battery (type CR-2025 or equi-
valent) with the positive (+)
side up. Slide the battery all
the way in under the battery
clip until it stops.
D . Turn the transmitter module
over and briefly press the
transmit switch (Fig. 3). The
on-board LED should light
brightly for 2 seconds.
E . Align
the
positioning
(Figure 3) with the guide pin in
*(1(5$/&200(176
Our wireless systems are very reliable and are tested to high
standards. However, due to their low transmitting power (required
by FCC, DTI and other regulatory authorities) there are some
limitations to be considered:
A . Receivers may be blocked by radio signals occurring on or
near their operating frequencies, regardless of the code
selected.
B . A receiver can only respond to one transmitted signal at a
time.
:$55$17<
:$55$17<
Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its
products hereinafter referred to as "the Product" or "Products" to be in conformance with
its own plans and specifications and to be free of defects in materials and workmanship
under normal use and service for a period of twelve months from the date of shipment by
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty
period, at its option, to repair or replace the product or any part thereof. The Manufacturer
shall not be responsible for dismantling and/or reinstallation charges. To exercise the
warranty the product must be returned to the Manufacturer freight prepaid and insured.
This warranty does not apply in the following cases: improper installation, misuse,
failure to follow installation and operating instructions, alteration, abuse, accident or
tampering, and repair by anyone other than the Manufacturer.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express or implied, including any warranty of
merchantability or fitness for a particular purpose, or otherwise. In no case shall the
Manufacturer be liable to anyone for any consequential or incidental damages for breach
of this warranty or any other warranties whatsoever, as aforesaid.
This warranty shall not be modified, varied or extended, and the Manufacturer does not
authorize any person to act on its behalf in the modification, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, including batteries, shall be
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, including batteries, used in conjunction with the Products.
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788
VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094
VISONIC LTD. (UK): UNIT 1, STRATTON PARK, DUNTON LANE, BIGGLESWADE, BEDS. SG18 8QS. PHONE: (01767) 600857 FAX: (01767) 601098
©VISONIC LTD. 1998 MCT-211 D-2451-0 NEW: DE2451- (REV. 1, 4/98)
2
Figure 3. Transmitter
Module - Top Side
dent
Figure 4. Battery Insertion
the base and place the module within the base. Then close
the case as instructed in Para. 3.5 below.
&ORVLQJWKH&DVH
A. Check that the rubber ring is in place around the rim of the
base. If not, place it carefully around the rim.
B. Align the cover with the base: make sure that the transparent
lens is over the transmit LED and the transmit pushbutton is
over the transmit switch (Fig. 3). Then press the cover and the
base together between your fingers.
C. Turn the reassembled unit upside down, and while keeping
both halves of the case pressed together, insert the four
screws and tighten them well.
C . Wireless equipment should be tested regularly (at least once
a week) to determine if there are sources of interference and
to protect against faults.
WARNING: Changes or modifications to
this unit not expressly approved by the
party responsible for compliance could void
the
user's
equipment.
The Manufacturer does not represent that its Product may not be compromised and/or
circumvented, or that the Product will prevent any death, personal and/or bodily injury
and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. User understands that a
properly installed and maintained alarm may only reduce the risk of events such as
burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such
will not occur or that there will be no death, personal damage and/or damage to property
as a result.
The Manufacturer shall have no liability for any death, personal and/or bodily injury
and/or damage to property or other loss whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
damage arising under this limited warranty or otherwise, regardless of cause or origin, the
Manufacturer's maximum liability shall not in any case exceed the purchase price of the
Product, which shall be fixed as liquidated damages and not as a penalty, and shall be the
complete and exclusive remedy against the Manufacturer.
Warning: The user should follow the installation and operation instructions and among
other things test the Product and the whole system at least once a week. For various
reasons, including, but not limited to, changes in environmental conditions, electric or
electronic disruptions and tampering, the Product may not perform as expected. The user
is advised to take all necessary precautions for his /her safety and the protection of
his/her property.
authority
to
operate
the
6/91
DE2451
Advertisement
