Table of Contents
Advertisement
Quick Links
Operator's Manual
Manuale d'istruzioni
Manuel d'instructions
Bedienungsanleitung
Manual de instrucciones
Gebruikershandleiding
Ägarhandbok
Brugehåndbog
Omistajankäsikirja
Eierens Håndbok
Manual de Instruções
O∆HΓIEΣ XPHΣEΩΣ
Használati útmutató
Promac 33
READ
CAREFULLY
LEGGERE
ATTENTAMENTE
LIRE
ATTENTIVEMENT
SORGFÄLTIG
LESEN
LEER
ATENTAMENTE
EERST GOED
DOORLEZEN
LÄS
NOGA
LÆS
OMHYGGELIGT
LUE
HUOLELLISESTI
LES
NØYE
LER
ATENTAMENTE
FIGYELEMMEL
OLVASANDÓ
- 33 cc
i
g
i
f
C
e
h
s
q
v
{
p
k
≤
Advertisement
Table of Contents
Related Manuals for McCulloch PROMAC 33
Summary of Contents for McCulloch PROMAC 33
- Page 1 Operator’s Manual Manuale d’istruzioni Manuel d’instructions Bedienungsanleitung Manual de instrucciones Gebruikershandleiding Ägarhandbok Brugehåndbog Omistajankäsikirja Eierens Håndbok Manual de Instruções O∆HΓIEΣ XPHΣEΩΣ Használati útmutató Promac 33 READ CAREFULLY LEGGERE ATTENTAMENTE LIRE ATTENTIVEMENT SORGFÄLTIG LESEN LEER ATENTAMENTE EERST GOED DOORLEZEN LÄS NOGA LÆS...
- Page 3 Partner McCulloch 50 : 1 40 : 1 25 : 1 2,5% 20 cm 3 25 cm 3 40 cm 3 1 ltr.
- Page 6 PROMAC 33 12” 300mm 242151B 852312B 3/8” 214215B (5/32”) g Due to a constant product improvement programme, the factory reserves the right to modify technical details mentioned in this manual without prior notice. i La casa produttrice si riserva la possibilità di variare caratteristiche e dati del pre- sente manuale in qualunque momento e senza preavviso.
-
Page 7: General Description
10 - CHOKE KNOB 11 - CARBURETOR ADJUSTMENT SCREWS If not used properly this Promac 33 can be dangerous. The warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this product. The operator is responsible for following the warnings and instructions in this manual and on the product. - Page 8 We recommend you have your unit periodically checked and serviced by an authorised dealer. Do not use chainsaw above shoulder height. 5 Do not operate the chainsaw near a naked flame or spilled fuel. Only operate the chainsaw outside and in well venti- lated areas.
- Page 9 Carefully survey the working site to note any hazards, eg. roads, paths, electricity cables, dangerous trees etc. Do not use the chainsaw if the device for stopping the chain C. Bar and chain installation - Intenz Ensure engine is always switched off before fitting or adjusting chain.
-
Page 10: Starting And Stopping
IMPORTANT Never start or operate unless bar and chain are properly installed. Before starting always move the saw away from the fuelling area and place it on a firm, flat surface, the guide bar to the front. STARTING A COLD ENGINE 1 Check that the chain brake is in the disengaged position moving the lever (L) towards the front handle. -
Page 11: Routine Maintenance
Then open screw 1 1/4 full turn (counterclockwise) . If the engine speed is too high, open the screw about 1/4 turn (counterclockwise). • I: The I (IDLE) screw controls the throttle opening to gov- ern idle speed (2900 min ) adjust as necessary. -
Page 12: Chain Sharpening
1 Chain cutter teeth can be sharpened with a round file, as follows: CHAIN MP 370 GLX The exact chain type is marked on the bottom half of the drive link which runs inside the bar groove. Filing can be made easier by also using a file holder. The chain can remain fitted on the bar during sharpening. -
Page 13: Fault Finding Table
Fault finding table Engine will not start Engine runs badly • • • • • • • • The chainsaw runs Engine runs badly or but does not cut well looses power when cutting • • • • ENGLISH - 7... -
Page 14: Ec Declaration Of Conformity
D Dichiarazione di Conformità CE Il sottoscritto, autorizzato dalla E.O.P.I., dichiara che la sega a catena portatile da legno Promac 33, costruito dalla E.O.P.I. 23868 Valmadrera (LC), Via Como 72, Italia, é conforme alle Direttive Europee: 98/37/CEE (Direttiva Macchine), 73/23/EEC (Direttiva Bassa Tensione), 93/68/CEE (Direttiva Marcatura CEE) &...