Table of Contents
Advertisement
– improper or poor: installation, repair, maintenance (includ-
ing tampering, modifications and repairs carried out by third
parties not authorized) and modification of safety systems;
– Use of non-original components (e.g.: consumables, wear
and tear, or spare parts);
– environment conditions provoking thermal (e.g. overheat-
ing/freezing) or chemical (e.g. corrosion/oxidation) stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents,
chips, and/or other damage to the finish of the product, unless
such damage results from defects in materials or workman-
ship and is reported within one (1) week of delivery unless
otherwise agreed;
C
APPLIANCE AND MANUFACTURER'S IDENTIFICATION DATA
The data plate gives the product identification and technical data.
An example of the marking or data plate on the appliance is given
below:
F.Mod.
xxxxxxxxx
Comm.Model
xxxxxxxx
xxxxxxxx
PNC 9VTX
Ser.Nr.
xxx kW
xxxx
W Tot.
Volt
xxx
Potenza Sbrinamento / Defrost Power
Resistenza Evaporazione / Evaporation Heater El.
x
Illuminazione / Lighting
x
IPxx
Electrolux Professional SPA - Viale Treviso, 15 - 33170 Pordenone (Italy)
The meaning of the various information given on it is listed below:
F.Mod.
factory description of product
Comm.Mod.
commercial description
PNC
production number code
Ser.No.
serial number
Type ref.
certification group of the appliance
Cyclopentane
expanding gas used in insulation
D
GENERAL INFORMATION
WARNING
Refer to "Warning and Safety
Information".
D.1
Introduction
This manual contains information relevant to various appliances.
The product images in this guide are only an example.
The drawings and diagrams given in the manual are not in scale.
They supplement the written information with an outline, but are
not intended to be a detailed representation of the appliance
supplied.
The numerical values given on the appliance installation
diagrams refer to measurements in millimeters and/or inches.
D.2
Intended use and restrictions
Refer to paragraph H.3 Switching the appliance on and
activation of thawing cycles for information on operation based
on manufacturer-set programming.
NOTWITHSTANDING ANY PROVISION TO THE CONTRARY,
ELECTROLUX PROFESSIONAL SHALL NOT BE RESPON-
SIBLE FOR AND HEREBY DECLINES AND DISCLAIMS ALL
LIABILITY FOR HAZARDS RELATING TO THE MAINTE-
NANCE OF FOOD SAFETY (INCLUDING RISK OF SERIOUS
16
xxxxxxxxx
Type ref.
xxxxxx
2019
Cyclopentane
xxx
xx
xx
Hz
Total Current
A
x
xxxx
xxx
kW
Classe / Class
GWP
CO2-eq
t
kW
xxxxx
xx
Refrigerante / Refrigerant
Kg
W
Cap.
x
• product with original serial numbers that have been removed,
altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by
Electrolux Professional.
Electrolux Professional warranty will be void and manufac-
turer shall have no liability related thereto in case of any
modification of the product or related hardware/software/
programming.
Warranty does not include scheduled maintenance activities
(including the parts required for it) or the supply of cleaning
agents unless specifically covered within any local agreement,
subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized
customer care.
V
power supply voltage
Hz
power supply frequency
kW
power input
A
absorbed current
Evaporation
evaporation heating element power
heater El.
Class
climatic class
GWP
global warming potential
CO2 eq
quantity of greenhouse gases
Lighting
internal light
Cap.
nominal capacity
Refrigerant
type of refrigerant gas
Defrost power
current absorbed
CE marking
WEEE symbol
IPX0
dust and water protection rating
INJURY, DISABILITY, AND/OR DEATH RELATING TO FOOD
BORNE ILLNESSES) AND COMPLIANCE WITH FOOD
SAFETY REGULATIONS. OPERATORS SHALL MONITOR
FOOD TEMPERATURES AND ENSURE THAT FOOD IS
MAINTAINED AT SAFE TEMPERATURES. WITHOUT LIMIT-
ING THE FOREGOING, MANUFACTURER DECLINES AND
DISCLAIMS ALL LIABILITY FOR IMPROPER PROGRAMING
AND USE OF THE PRODUCT BY OPERATOR.
D.3
Testing and inspection
Our appliances have been designed and optimized, with
laboratory testing, in order to obtain high performance and
efficiency.
The appliance is shipped ready for use.
Passing of the tests (visual inspection - electrical test - functional
test) is guaranteed and certified by the specific enclosures.
D.4
Copyright
This manual is intended solely for consultation by the operator
and can only be given to third parties with the permission of
Electrolux Professional company.
Advertisement
Table of Contents
