AUTODOME IP 4000 HD Table of contents | en Table of contents Safety About this Manual Legal Information Safety Precautions Important Safety Instructions Connection in Applications Important Notices Customer Support and Service Introduction Parts List System Overview Mounting Accessories Installation Overview...
| Table of contents AUTODOME IP 4000 HD 12.1 Parts List 12.2 Installation Requirements 12.3 Preparing for Installation 12.4 Installing the Junction Box (VDA-AD-JNB) Connection Troubleshooting Maintenance Decommissioning 16.1 Transfer 16.2 Disposal Technical data 2015.11 | 1.1 | Installation Manual...
Legal Information Copyright This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.
® Electrical Code (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1), and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for any damages or losses caused by incorrect or improper installation. Warning! Bosch’s version of High PoE:...
If auxiliary power (24 VAC) and PoE+ are applied simultaneously, the camera selects auxiliary input and shuts off PoE+. For pendant models used in outdoor applications that require heaters, a Bosch High PoE 60W midspan (NPD-6001A, sold separately) is required to power both the camera and its internal heaters.
U.S. Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4. Customer Support and Service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Service Centers...
Page 9
Asia Pacific Region Please contact your local distributor or Bosch sales office. Use this link: http://www.boschsecurity.com/startpage/html/asia_pacific.htm More Information For more information please contact the nearest Bosch Security Systems location or visit www.boschsecurity.com Bosch Security Systems Installation Manual 2015.11 | 1.1 |...
Verify that all the parts listed in the Parts List below are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. – Do not use this product if any component appears to be damaged. Please contact Bosch Security Systems in the event of damaged goods. –...
System Overview | en System Overview The AUTODOME IP 4000 HD is a compact, indoor PTZ dome camera with a high-resolution 720p25/30 (1MP) or 1080p25/30 (2MP) HD sensor and a powerful 12x optical zoom that allows operators to monitor wide scenes without losing any details. The camera’s aesthetic...
| Mounting Accessories AUTODOME IP 4000 HD Mounting Accessories The following mounting accessories are available (and are supplied with separate mounting instructions) for AUTODOME IP 4000 HD cameras. Model Number Description Application NEZ-A4-WW Wall mount kit Indoor/outdoor vertical walls...
Electrical Code (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1), and all applicable local codes. Bosch Security Systems, Inc. accepts no liability for any damages or losses caused by incorrect or improper installation. 1. Select the mounting location.
Page 14
| Installation Overview AUTODOME IP 4000 HD Figure 5.1: Loosen enclosure screws (pendant models) Remove the trim ring / bubble enclosure. Figure 5.2: Remove trim ring and bubble (pendant models) Note: The next two steps are for the in-ceiling model only.
AUTODOME IP 4000 HD Installing a microSD card (optional) | en Installing a microSD card (optional) Push the camera block until you see the card slot (item 1 in the following figure). Insert the card into the slot (item 2 in the following figure).
Page 16
| Installing a microSD card (optional) AUTODOME IP 4000 HD Figure 6.3: Replace trim ring/bubble (pendant models) Figure 6.4: Tighten screws (pendant models) Proceed with installation. 2015.11 | 1.1 | Installation Manual Bosch Security Systems...
AUTODOME IP 4000 HD Installing an In-Ceiling Camera in a Drywall Ceiling | en Installing an In-Ceiling Camera in a Drywall Ceiling Tools Required – Appropriate straight slot screwdriver – Appropriate tool for cutting a hole in drywall or ceiling tile (if applicable) Installation Requirements –...
Page 18
| Installing an In-Ceiling Camera in a Drywall Ceiling AUTODOME IP 4000 HD Figure 7.4: Connect cables to camera Insert the camera (without the trim ring / bubble enclosure) into the hole in the ceiling. Ensure not to pinch the cables.
Page 19
AUTODOME IP 4000 HD Installing an In-Ceiling Camera in a Drywall Ceiling | en Figure 7.7: Camera installed in ceiling Bosch Security Systems Installation Manual 2015.11 | 1.1 |...
| Installing an In-ceiling Camera in a Suspended Ceiling AUTODOME IP 4000 HD Installing an In-ceiling Camera in a Suspended Ceiling Tools Required – Appropriate straight slot screwdriver – Appropriate tool for cutting a hole in drywall or ceiling tile (if applicable) Installation Requirements –...
AUTODOME IP 4000 HD Installing an In-ceiling Camera in a Suspended Ceiling | en Figure 8.2: Cut Hole in Ceiling Tile Tighten the four (4) securing screws to the Bracket Assembly. Figure 8.3: Tighten Bracket Securing Screw Secure the Bracket Assembly to an overhead securing point with a safety wire.
Page 22
| Installing an In-ceiling Camera in a Suspended Ceiling AUTODOME IP 4000 HD Figure 8.5: Connect cables to camera Insert the camera (without the trim ring / bubble enclosure) into the hole in the ceiling. Ensure not to pinch the cables.
Page 23
AUTODOME IP 4000 HD Installing an In-ceiling Camera in a Suspended Ceiling | en Figure 8.8: Camera installed in ceiling Bosch Security Systems Installation Manual 2015.11 | 1.1 |...
| Installing a Surface Mount and Camera AUTODOME IP 4000 HD Installing a Surface Mount and Camera Tools Required – Appropriate straight slot screwdriver – Appropriate tool for cutting a hole in drywall or ceiling tile (if applicable) –...
AUTODOME IP 4000 HD Installing a Surface Mount and Camera | en Installing the Surface Mount Adapter Determine a secure location for mounting the surface mount adapter (NEZ-A4-SMB) and the camera. Use the adapter as a template to mark the installation location for four (4) M4 or #10 pan head screws (with a minimum length of 10 mm (0.39 in.)) (user-supplied).
Page 26
| Installing a Surface Mount and Camera AUTODOME IP 4000 HD NEZ-A4-SMB 3x M4 Figure 9.4: Attach mounting plate to SMB 2015.11 | 1.1 | Installation Manual Bosch Security Systems...
AUTODOME IP 4000 HD Installing a Surface Mount and Camera | en Figure 9.5: Indicator for correct point of connection Installing the Camera to the Mounting Plate Route the cables from the ceiling out of the side of the mounting plate with the crescent- shaped cut-out.
Page 28
| Installing a Surface Mount and Camera AUTODOME IP 4000 HD Figure 9.6: Cable connections, safety tether Unlock the single safety locking screw on the base of the unit using the T10 Torx screwdriver (item 2 in the following figure).
Page 29
AUTODOME IP 4000 HD Installing a Surface Mount and Camera | en ≈ 15° Figure 9.7: Camera to mounting plate Remove the protective plastic sheet from the bubble. Installation is complete. Bosch Security Systems Installation Manual 2015.11 | 1.1 |...
| Installing a Wall Mount and Camera AUTODOME IP 4000 HD Installing a Wall Mount and Camera 10.1 Parts List The Wall Mount (NEZ-A4-WW) includes the following parts: Quantity Item Wall mount Dome mounting cap Screws, M4 Screw, #10 Installation Manual 10.2...
AUTODOME IP 4000 HD Installing a Wall Mount and Camera | en Route the external cables (24 VAC, CAT 5/CAT6, alarm and/or audio as needed) through the hole in the junction box. Figure 10.2: Route cables through junction box Route all cables from the junction box through the arm of the wall mount.
| Installing a Wall Mount and Camera AUTODOME IP 4000 HD 10.6 Installing the Wall Mount Attach the mounting cap to the arm of the wall mount. Figure 10.4: Cap to Wall Mount Attach the arm to the junction box with appropriate SEMS screws (user-supplied) that have an integral lock washer to dig through the paint.
AUTODOME IP 4000 HD Installing a Wall Mount and Camera | en Figure 10.6: Attach mounting plate to wall mount 10.7 Installing the Camera to the Mounting Plate Route the cables from the ceiling out of the side of the mounting plate with the crescent- shaped cut-out.
Page 34
| Installing a Wall Mount and Camera AUTODOME IP 4000 HD Ground wire Connect the mating connectors from the cables from the junction box to the matching connectors from the camera. Refer to the chapter Connection for more information.
Page 35
AUTODOME IP 4000 HD Installing a Wall Mount and Camera | en ≈ 15° Figure 10.9: Camera to mounting plate Confirm that the housing is electrically grounded. Remove the protective plastic sheet from the bubble. Installation is complete. Figure 10.10: Camera installed on wall mount...
| Installing a Pipe Mount and Camera AUTODOME IP 4000 HD Installing a Pipe Mount and Camera 11.1 Parts List The Pipe Mount (NEZ-A4-PW) includes the following parts: Quantity Item Pipe Mount Base Dome mounting cap 300 mm (11.8 in.) Pipe Extension 200 mm (7.9 in.) Pipe Extension...
Page 37
AUTODOME IP 4000 HD Installing a Pipe Mount and Camera | en 88.8 (3.5) 88.8 (3.5) 751.9 (29.6) 3/4-14 NP 544.9 SM Threads (21.5) Ø11.2 (4x) (0.44) 444.9 (17.5) Ø153.0 Figure 11.1: Pipe Mount Dimensions Use the four (4) holes in the flange as a template to mark the position where the holes should be drilled to secure the mount.
Page 38
| Installing a Pipe Mount and Camera AUTODOME IP 4000 HD Figure 11.3: Dome cap and pipe mount Secure the flange using four (4) appropriate user-provided fasteners such as Moly or Toggle bolts. Notice! The fasteners and mounting surface must be capable of supporting a maximum load of 11.33 kg (25 pounds).
Page 39
AUTODOME IP 4000 HD Installing a Pipe Mount and Camera | en Figure 11.4: Attach Pendant Pipe Mount to Ceiling Caution! Select a rigid mounting location to prevent excessive vibration to the camera. Attach user supplied ground lug. Align holes of mounting plate (supplied with dome) with dome mounting cap and attach with the three (3) screws supplied.
Page 40
| Installing a Pipe Mount and Camera AUTODOME IP 4000 HD Figure 11.5: Attach Mounting Plate to Dome Cap Crescent Shape Ground Lug Dome Cap Mounting Plate 2015.11 | 1.1 | Installation Manual Bosch Security Systems...
AUTODOME IP 4000 HD Installing a Pipe Mount and Camera | en 11.6 Installing the Camera to the Mounting Plate Route the cables from the ceiling out of the side of the mounting plate with the crescent- shaped cut-out. Attach the hook of the safety tether from the adapter to the bottom of the camera.
Page 42
| Installing a Pipe Mount and Camera AUTODOME IP 4000 HD Figure 11.7: Connect cables Unlock the single safety locking screw on the base of the unit using the T10 Torx screwdriver (item 2 in the following figure). Attach the camera to the mounting plate by inserting the vertical tab on the plate into the recessed slot on the top of the camera dome to the right of the safety locking screw.
Page 43
AUTODOME IP 4000 HD Installing a Pipe Mount and Camera | en ≈ 15° Figure 11.8: Camera to mounting plate Confirm that the housing is electrically grounded. Remove the protective plastic sheet from the bubble. Installation is complete. Figure 11.9: Camera installed on pipe mount...
| Installing a Junction Box (VDA-AD-JNB) AUTODOME IP 4000 HD Installing a Junction Box (VDA-AD-JNB) 12.1 Parts List The junction box (VDA-AD-JNB) includes the following parts: Quantity Item Junction box Torx screwdriver Screws, M4 (for the innermost set of holes on the front cover)
Page 45
AUTODOME IP 4000 HD Installing a Junction Box (VDA-AD-JNB) | en Note: The option to mount the junction box directly to a wall is valid only if you plan to install the camera to a wall mount bracket. You cannot use this option with a corner mount bracket or a pole mount bracket because those two brackets attach to the back of the junction box instead of to the front.
Page 46
| Installing a Junction Box (VDA-AD-JNB) AUTODOME IP 4000 HD If desired, use the cable management points in the bottom of the inside of the junction box to consolidate the cables. – Remove one of the cable management clamps (items c and d in the following figure).
Page 47
AUTODOME IP 4000 HD Installing a Junction Box (VDA-AD-JNB) | en To mount a VEZ-A5-WMB wall mount bracket onto the junction box, insert the four (4) M8 mounting screws through the holes in the arm of the wall mount bracket into the middle set of holes on the front cover of the junction box.
Page 48
| Installing a Junction Box (VDA-AD-JNB) AUTODOME IP 4000 HD To mount a VGA-A-9542 corner mount bracket onto the junction box, insert the four (4) M10 mounting screws through the inner set of holes in the center section of the corner mount bracket into the middle set of holes on the back cover of the junction box.
Page 49
AUTODOME IP 4000 HD Connection | en Connection Warning! Bosch’s version of PoE+ If supplying power to the camera by PoE+ or by a midspan device, you must install additional surge protection. Warning! Bosch’s version of High PoE: If supplying power to the camera by HPoE or a midspan device, you must install additional surge protection.
Page 50
| Connection AUTODOME IP 4000 HD 2 IP connection (Ethernet/CAT5/CAT6) (100 m maximum) 3 Network switch 4 Network device (computer with monitor, DVR/NVR, etc.) If desired, connect the alarm and/or audio wires as identified in the following table. Label ID...
AUTODOME IP 4000 HD Troubleshooting | en Troubleshooting If problems occur, check the installation of the camera with the instructions in this manual. Refer to this guide for further information. Problem Solution No video on screen. - Verify that the power is connected to all components in the system.
Page 52
Notice! To avoid excessive moisture saturation inside the housing, limit the amount of time that the bubble is disconnected from the housing. Bosch recommends that the bubble be removed from the housing for no more than five (5) minutes. Bubble Handling The bubble may be packaged with a protective plastic sheet.
Page 53
Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com to order or to find a local distributor.
Page 54
16.2 Disposal Disposal Your Bosch product has been developed and manufactured using high- quality materials and components that can be reused. This symbol means that electronic and electrical devices that have reached the end of their working life must be disposed of separately from household waste.