Resetting The Main Unit; Switching The Speaker Impedance; Power Cord Caution; Specifications - Pioneer 516-S/-K Operating Instructions Manual

11 Additional information

Resetting the main unit

Use this procedure to reset all the receiver's
settings to the factory default. Use the front
panel controls to do this.
1 Switch the receiver into standby.
2 While holding down the TONE button,
press and hold the
about three seconds.
3 When you see RESET? appear in the
display, press the ENTER button.
OK? shows in the display.
4 Press SETUP to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.

Switching the speaker impedance

We recommend using speakers of 8 Ω with this
system, but it is possible to switch the imped-
ance setting if you plan to use speakers with a
6 Ω impedance rating.
• With the receiver in standby, press the
SPEAKER IMPEDANCE button.
Each time you do this, you switch between the
impedance settings:
• SP 6 OHM – Use this setting if your
speakers are rated at 6 Ω.
• SP 8 OHM – Use this setting if your
speakers are rated at 8 Ω or more.

Power cord caution

Handle the power cord by the plug. Do not pull
out the plug by tugging the cord and never
touch the power cord when your hands are wet
as this could cause a short circuit or an electric
shock. Do not place the unit, a piece of
furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it
46
En
STANDBY/ON button for
with other cords. The power cords should be
routed such that they are not likely to be
stepped on. A damaged power cord can cause
a fire or give you an electrical shock. Check the
power cord once in a while. When you find it
damaged, ask your nearest Pioneer authorized
service center or your dealer for a replacement

Specifications

Amplifier section
• Continuous power output (stereo)
Front . . . . . . . 100 W (DIN 1 kHz, THD 1.0 %, 8
• Power output (surround)
Front
. . . . . 100 W per channel (1 kHz, THD 1.0 %, 8
Center . . . . . . . . . . 100 W (1 kHz, THD 1.0 %, 8
Surround. . . . . . . . . . . . . . . . . .100 W per channel
Surround Back (VSX-516 model only)
. . . . . 100 W per channel (1 kHz, THD 1.0 %, 8
Audio section
• Input (Sensitivity/Impedance)
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT. . . . . . . . . . . . . . . .200 mV/47 k
• Frequency response
CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD,
TV/SAT. . . . . . . . . . . . . . . 5 Hz to 100 000 Hz
• Output (Level/Impedance)
DVR/VCR REC, CD-R/TAPE/
MD REC . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 k
• Tone control
Bass . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (100 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (10 kHz)
Loudness . . . . . . +10 dB/+5 dB (100 Hz/10 kHz)
• Signal-to-Noise Ratio DIN (Continuous
rated power output / 50mW)
CD, DVR/VCR, CD-R/TAPE/MD,
DVD/LD, TV/SAT. . . . . . . . . . . . . . . . . 88 dB/64 dB
Ω
Ω
Ω
Ω
(1 kHz, THD 1.0 %, 8
Ω
Ω
dB
Ω
(at volume level –50 dB)
)
)
)
)
)